Operating Instructions For safe and correct use, be sure to read "Safety Information" before using the machine.
TABLE OF CONTENTS Introduction.........................................................................................................................................................5 Copyrights to Images.....................................................................................................................................5 Important.........................................................................................................................................................
Turning On the Projector.............................................................................................................................34 Selecting an Input Signal.............................................................................................................................35 Adjusting the Angle of the Projection.........................................................................................................36 Adjusting the Image...........................................
Image Adjustment Menu..................................................................................................................................83 Display Settings Menu.....................................................................................................................................87 Default Settings Menu......................................................................................................................................90 Network/USB Settings Menu..................
Copyrights......................................................................................................................................................137 Where to Inquire............................................................................................................................................138 Trademarks.....................................................................................................................................................139 INDEX...................
Introduction Copyrights to Images When projecting images using the projector, be careful not to infringe the copyright of protected materials. The following are examples that may infringe the copyright of protected materials.
• To view 3D images, sit in front of the screen so that your eyes are parallel and level with the screen. • Viewing 3D images from a place that is too close to the screen may result in eye strain. The distance between the screen and you should be at least three times the height of the screen. • Adult supervision is required for children using 3D glasses. • Viewing 3D images is not recommended for children under 6 years old. It may negatively affect development of their vision.
Manuals Provided with the Projector Manuals for the Projector Read this manual carefully before you use the projector. Refer to the manuals that are relevant to what you want to do with the projector. • The manuals are provided in various formats. • Adobe® Acrobat® Reader®/Adobe Reader must be installed in order to view the manuals as PDF files. Safety Information Provides information about safe usage of the projector. To avoid injury and prevent damage to the projector, be sure to read Safety Information.
Manual Name Operating Instructions 8 Printed Manuals Provided PDF Manuals Provided No Yes
Viewing the PDF Manual on the CD-ROM This section describes how to view the PDF manual on the supplied manual CD-ROM. File path The manual is included in the following folder on the CD-ROM: Manual\(language) 1. Insert the CD-ROM in the CD-ROM drive of your computer. 2. Specify a language. The launcher screen appears. 3. Click [Read PDF manuals]. The PDF manual is displayed on the screen. • To view the PDF manuals, you need to have Adobe Acrobat Reader/Adobe Reader installed on your computer.
How to Read This Manual Symbols This manual uses the following symbols: Indicates points to pay attention to when using the projector. Indicates supplementary explanations of the projector’s functions, and instructions on resolving user errors. [] Indicates the names of buttons on the control panel and remote control. It also indicates items displayed on the menu screens. Notes Contents of this manual are subject to change without prior notice. Two kinds of size notation are employed in this manual.
1. Preparations for Using the Projector This chapter explains the names and functions of the different parts of the projector and remote control, and how to use them. It also explains how to position the projector and how to connect it to other equipment. Main Functions The projector features the following functions that you can use.
1. Preparations for Using the Projector It is possible to convert PowerPoint materials to JPEG format using JPEG Conversion Tool and then project them using the projector. Mouse remote control You can operate the mouse pointer on a computer by using the remote control provided with the projector. Network Utility Network Utility is an application that is provided with the projector and is used for connecting the projector and a computer to project images.
Checking the Accessories Checking the Accessories The projector is provided with the following accessories. Make sure that everything is included in the package. If anything is missing or damaged, contact your sales representative or service representative.
1. Preparations for Using the Projector • The bundled accessories may vary depending on the location that this product was purchased. • Use only the RGB cable provided with the projector. • Use only the power cord set provided with the projector. • The Operating Instructions and various applications are on the provided CD-ROM. For procedures about how to read Operating Instructions, see p.9 "Viewing the PDF Manual on the CD-ROM". For instructions about using the applications, see p.
Projector Parts and Their Functions Projector Parts and Their Functions Control Panel (Top View) 1 2 3 4 5 6 7 CLB009 1. [Power] button Turns the projector on and off. You can confirm the status of the projector with the indicator. • On: Power is on. • Off: Power is off. • Flashing at 1 or 3 second intervals: Standby. • Flashing at short intervals: Starting up or cooling. 2. [Input] button Switches the signal input. The input signal changes each time the button is pressed. 3.
1. Preparations for Using the Projector 6. Arrow buttons Used to operate the menu screen. The [ ] and [ ] buttons are used to adjust the size of the projected image. The [ ] and [ ] buttons are used to adjust the volume. 7. Projection window Enlarges and projects the image (light). • The top of the projector is covered with a protective film when it is shipped. Remove the film before using the projector. Front and Left-Side View 1 2 3 4 5 CLB010 1.
Projector Parts and Their Functions Rear and Right-Side View 1 3 2 4 5 6 7 8 9 CLB011 1. USB port For connecting a USB memory device or USB device cable. 2. HDMI port For connecting an HDMI (High-Definition Multimedia Interface) cable. 3. LAN port For connecting an Ethernet cable. 4. Computer In port (Y/Pb/Pr) For inputting RGB signals from a computer or component image signals (Y/Pb/Pr) from a video player. 5. Video In port For inputting image signals from a video player. 6.
1. Preparations for Using the Projector Remote Control Parts and Their Functions 1 6 2 7 12 18 8 13 19 9 20 14 3 4 10 5 11 21 22 15 23 16 24 17 25 CLB013 1. [Menu] button Displays the menu screen. Press it again to close the menu screen. 2. [Input] button Switches the signal input. The signal that is input changes each time the button is pressed. 3. [Page] buttons Changes slides, such as in a PowerPoint presentation. Press [ ] to go to the next page.
Remote Control Parts and Their Functions 9. [Enter] button Enters the selected item or mode. 10. [Volume] buttons Adjusts the volume of the speaker. Press the [ ] button to increase the volume. Press the [ ] button to decrease the volume. 11. [Zoom] buttons Reduces the image. Press the [ ] button to reduce the image. Press the [ ] button to enlarge the image to its original size. 12. [HDMI] button Switches to HDMI input mode. 13. [Computer] button Switches to computer input mode.
1. Preparations for Using the Projector How to Use the Remote Control You can use the remote control to turn the projector on and off, and to change the signal of the image being input and projected. You can also enlarge or reduce the image and mute the audio. Note the following precautions when using the remote control: • Do not drop or hit the remote control. • Do not place the remote control in a place that is very hot or very humid. • Do not get the remote control wet.
How to Use the Remote Control Loading Batteries into the Remote Control • For safe operation, follow the warnings below regarding the batteries used in the remote control. If you use the batteries incorrectly, it may result in fire or injury due to batteries leaking or exploding. • Do not use batteries other than the ones specified. • Do not mix and use batteries that are different types or that are new and old. • Correctly insert batteries according to the polarity ( / ).
1. Preparations for Using the Projector 2. Insert the batteries. CLB016 Note the direction of the positive and negative terminals when inserting the batteries. 3. Close the battery cover. CLB017 • Replace the batteries if the remote control does not work or if the effective distance becomes too narrow. Inputting Text Use the keyboard that is displayed on screen to input text on the setting screen. 1. Use the [ ], [ ], [ ], and [ ] buttons on the remote control to select a character on the screen.
How to Use the Remote Control 2. Press the [Enter] button. The selected character appears in the text area. 3. After inputting all the characters, select [OK]. 4. Press the [Enter] button. The text is input. • You can also use the number buttons on the remote control to input numbers. Operating a Computer with the Remote Control You can operate a computer using the projector's remote control. This function can be used when the mouse remote control receiver is connected to a computer.
1. Preparations for Using the Projector 2. [Enter] button Left clicks. 3. [R-Click] button Right clicks. 4. [Page] button The [ ] and [ ] buttons change the pages in a PowerPoint presentation. 1. Connect the mouse remote control receiver to the computer. 2. Point the remote control at the mouse remote control receiver and press the buttons. • Some computers cannot be operated using the projector's remote control.
How to Use the Remote Control • The remote control cannot operate a projector unless the ID on the remote control is the same as the controller ID specified in the projector's Default Settings menu. • The ID number specified in the remote control is effective until a different ID number is specified. • The ID number in the remote control must be specified again if the batteries are changed.
1. Preparations for Using the Projector Positioning the Projector When positioning the projector, place it so that the projector's rear side faces the screen. Make sure the projector and the screen are parallel to each other. Adjust the distance between the projector and the screen according to the size of the projected image. For details, see p.26 "Relationship Between the Projection Distance and the Screen Size". Projection Mode You can position the projector in one of two ways.
Positioning the Projector b a CLB023 a b Projection distance Projection height 48 inches 12 cm (4.6 inches) 9 cm (3.7 inches) 60 inches 17 cm (6.5 inches) 12 cm (4.7 inches) 80 inches 25 cm (9.8 inches) 16 cm (6.2 inches) Projection size*1 *1 The sizes of the projected images are for a full size image without keystone adjustment.
1. Preparations for Using the Projector Connecting Equipment to the Projector • Do not place the power cord and connection cable in a way that might cause someone to trip and fall. The product might fall over and cause an injury. Various equipments can be connected to the projector. Turn off the power to any equipment before connecting it to the projector. Be sure to read the manual for the applicable equipment before connecting it to the projector.
Connecting Equipment to the Projector Connecting AV Equipment Use a cable that supports the signal being input when connecting AV equipment. To connect a DVD recorder, connect a conversion adapter BNC-pin to the Computer In port of the projector and to the Y/Pb/Pr output of the recorder. To connect a video recorder or a DVD player, connect a video cable to the Video In port of the projector and to the video output of the recorder or the player.
1. Preparations for Using the Projector Connecting the Power Cord • Do not use any power sources other than those that match the specifications shown. Doing so could result in fire or electric shock. • Do not use any frequencies other than those that match the specifications shown. Doing so could result in fire or electric shock. • The supplied power cord is for use with this machine only. Do not use it with other appliances. Doing so could result in fire or electric shock.
Connecting the Power Cord 1. Insert the connector of the power cord set into the AC In socket on the right side of the projector. CLB028 2. Insert the power plug into a power outlet. • Do not place anything near the power outlet. • When [Power On Method] in [Default Settings] is specified as [Auto.], the projector turns on as soon as the power plug is inserted in a power outlet (direct power on).
1.
2. Projecting an Image This chapter explains the procedure for projecting an image. Basic Operations • Do not look into the projection window or vent when the product is on. The bright light may damage your eyes. Be especially careful in an environment with children. • Do not place low heat resistant material near the exhaust vents. Hot air may come from the exhaust vents, resulting in damage to the product or an accident. • Do not block the projection light when it is on.
2. Projecting an Image Turning On the Projector Make sure that the power plug is inserted into a power outlet. For details, see p.30 "Connecting the Power Cord". 1. Press the [Power] button. CLB030 The projector beeps and the indicator flashes blue. The start-up screen is displayed. • Make sure the projector is positioned squarely in front of the screen. For details, see p.26 "Positioning the Projector". • When the projector is turned on for the first time after it is purchased, the start menu appears.
Basic Operations • The start menu is only displayed the first time the projector is used. However, the start menu is displayed when the projector is turned on after [Reset All] in [Default Settings] is executed. • The display language and lamp power level can also be changed in the menu screen. For details, see p.90 "Default Settings Menu". Selecting an Input Signal Select a signal that is compatible with the equipment that is connected to the projector. 1.
2. Projecting an Image When projecting the screen of a notebook computer When connecting a notebook computer to the projector, switch the computer's image output. In Windows operating systems, the image output can be switched with a function key. While pressing and holding the [Fn] key, press the key, the key, or the LCD/VGA function key.
Basic Operations 1. Lift the front of the projector and adjust the length of the adjustable feet. CLB031 Turn the adjustable feet to the left to make it longer. Turn the adjustable feet to the right to make it shorter. • Adjust the height of the right and left adjustable feet so the projector is level. If the projector is inclined too much, an error occurs and operation cannot be performed.
2. Projecting an Image 1. Press the [Zoom ] button to reduce the image. CLB037 The ratio decreases each time the [ ] button is pressed. You can confirm the current ratio on the value bar at the bottom of the screen. 2. Press the [Zoom ] button to enlarge the image. The ratio increases each time the [ ] button is pressed. The image is enlarged until it reaches the original size. • You can also adjust the size of the projected image from the control panel on the projector.
Basic Operations Adjusting for keystone distortion If the projector is placed at an angle, the projected image will be distorted. This is called keystone distortion. If [Auto Keystone] in [Default Settings] is specified as [Off], manually adjust for keystone distortion. CLB033 1. Press the [Keystone ] and [Keystone ] buttons to adjust the keystone distortion. CLB063 The value bar appears at the bottom of the screen. Press the [ ] button to increase the correction value.
2. Projecting an Image 1. Press the [Auto set] button. CLB034 • Depending on the type of input signal, some images may not be displayed or correctly adjusted. If this happens, adjust the image with [Position] in [Image Adjustment]. For details about the types of signals that can be input to the projector, see p.127 "List of Compatible Signals". Adjusting the Volume of the Speaker 1. Press the [Volume ] and [Volume ] buttons to adjust the volume.
Basic Operations Enlarging the image Enlarges and displays a part of the image. The image can be enlarged in a range of 100 to 200%. The enlarged image becomes grainy due to the digital processing. 1. Press the [Magnify ] button to enlarge the image. CLB036 The ratio increases each time the [ ] button is pressed. Pressing the [ ], [ ], [ ], and [ ] buttons moves the display position of the enlarged image. 2. Press the [Magnify ] button to reduce the image.
2. Projecting an Image 1. Press the [AV Mute] button. CLB038 The image blanks and the audio mutes. 2. To cancel this function, press the [AV Mute] button again. • An icon appears on the screen when mute is used. • The mute function is canceled automatically if any button on the control panel is pressed. • You can also use the [AV Mute] button on the projector's control panel. Pausing the image Pauses the video or moving image that is being projected. 1. Press the [Freeze] button.
Basic Operations • When the [Freeze] button is pressed, the image that is being projected at that time is stored in memory, and that image is projected. Because of this, even though the projector has paused the image, the equipment continues to play the video. Changing the image quality 1. Press the [Picture] button. CLB039 2. Select a setting from the list using the [ ] and [ ] buttons, and then press the [Enter] button. • You can also change the screen mode with [Image Adjustment].
2. Projecting an Image • You can also change the aspect with [Display Settings]. For items that can be specified, see p.87 "Display Settings Menu". Switching the lamp mode Select eco mode if the image is too bright or when projecting images in a dark room. 1. Press the [Eco] button. CLB042 The mode changes each time the button is pressed. • You can also change the lamp power level with [Default Settings]. For items that can be specified, see p.87 "Display Settings Menu". Turning Off the Projector 1.
Basic Operations 2. Press the [Power] button. The projector beeps and the projector turns off. • After turning the projector off, wait about five minutes for the lamp to cool before turning the projector on again. The lamp may not light if it is very hot. • The projector turns off as soon as the power plug is removed from the power outlet (direct power off).
2. Projecting an Image Projecting Images from a USB Memory Device or Digital Camera The projector can project JPEG and MPEG files stored on a USB memory device that is connected to the projector. JPEG files stored in digital cameras can also be projected. Images can be displayed easily even if a computer is not connected. The USB devices must support USB 2.0. • It is recommended to back up the data saved to a USB device before using it.
Projecting Images from a USB Memory Device or Digital Camera Connecting the USB Device Connect the USB memory device or digital camera to the projector. The USB device can be connected even if the projector is already on. 1. Connect the USB device to the USB port on the projector. Check the port orientation before connecting. CLB043 • If the projector does not recognize the USB device when it is connected, disconnect and reconnect the USB device.
2. Projecting an Image 1. Press the [USB] button. CLB044 The input signal switches to the USB, and the files within the root directory are displayed. 2. Use the [ ] and [ ] buttons to select the JPEG file or folder. 3. Press the [Enter] button. If you select a JPEG file, its image is projected. If you select a folder, the file list within the folder is displayed. Repeat steps 2 and 3 until you can display the file you want to project.
Projecting Images from a USB Memory Device or Digital Camera 1. Press the [USB] button. CLB044 The input signal switches to the USB, and the files within the root directory are displayed. 2. Use the [ ] and [ ] buttons to select the MPEG file or folder. 3. Press the [Enter] button. If you select an MPEG file, the video plays. If you select a folder, the file list within the folder is displayed. Repeat steps 2 and 3 until you can display the file you want to project.
2. Projecting an Image You can do presentations without a computer if you save converted JPEG files to a USB memory device and then display the slides using the projector. The converted files can also be transferred to a server.
Projecting Images from a USB Memory Device or Digital Camera How to use JPEG Conversion Tool JPEG Conversion Tool is included on the supplied CD-ROM. 1. Insert the CD-ROM in the CD-ROM drive of your computer. 2. Specify a language. The launcher screen appears. 3. Click [JPEG Conversion Tool Type A]. 4. Specify a destination to save the application. The "RICOH JPEG Conversion Tool Type A" folder is copied to the computer. 5. To create a shortcut icon on the desktop, click [OK]. 6. Close the screen.
2.
3. Using the Projector via a Network This chapter explains the settings for using the projector via a network. This chapter also explains the operations that use Network Utility. Connecting the Projector to a Network The projector can be connected to a network using a wireless LAN or an Ethernet cable. For details, see p.55 "Connecting Using an Ethernet Cable", or p.57 "Connecting Using a Wireless LAN".
3. Using the Projector via a Network For details, see p.96 "Network Settings". • When operating the projector from a computer via a network, use Network Utility which is provided with the projector. For details, see p.61 "Projecting Images Using Network Utility".
Connecting Using an Ethernet Cable Connecting Using an Ethernet Cable • Do not place the power cord and connection cable in a way that might cause someone to trip and fall. The product might fall over and cause an injury. The projector is compatible with 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet interfaces. • If the projector is turned on, turn it off before connecting the Ethernet cable.
3. Using the Projector via a Network • Use an Ethernet cable that is shielded. • To use the projector via a network, you must specify settings such as the IP address in the Network Settings menu. For items that must be specified, see p.53 "Connecting the Projector to a Network".
Connecting Using a Wireless LAN Connecting Using a Wireless LAN • Do not use a wireless LAN if there is electromagnetic interference from other equipment. Doing so may cause an accident due to the other equipment malfunctioning from the electromagnetic interference. The projector has a built-in wireless LAN board. Wireless uses radio waves to exchange information instead of an Ethernet cable.
3. Using the Projector via a Network Ad Hoc mode This mode communicates with the computer directly, and not via an access point. No other equipment is required, so this mode is suited for locations that have no network environment. If you use ad hoc mode, make the following settings: Settings Using Simple 1:1 Connection Action Method Refer to Wireless LAN settings Simple 1:1 Connection (Network Utility) p.62 "Simple 1:1 Connection" Image projection Simple 1:1 Connection (Network Utility) p.
Connecting Using a Wireless LAN Settings Using Simple Wireless LAN Setup Action Method Refer to Wireless LAN settings Simple Wireless LAN Setup p.59 "Simple Wireless LAN Setup" Image projection Network Connection (Network Utility) p.63 "Network Connection" Simple Wireless LAN Setup To use the projector via a wireless LAN, the network settings must be configured. If you use the wireless LAN simple setup function, the infrastructure settings can be easily configured.
3. Using the Projector via a Network 3. Select [Network Settings]. 4. Select [Wireless LAN]. 5. Select either [Connect by PIN] or [Connect by Push] in [Simple Wireless LAN Setup]. 6. If [Connect by PIN] is selected, enter the PIN code generated by the access point in the projector, and then proceed to step 7. You must preconfigure the access point's simple wireless LAN setup function. 7. If [Connect by Push] is selected, press the access point push button. 8. Select [OK] on the confirmation screen.
Projecting Images Using Network Utility Projecting Images Using Network Utility What Is Network Utility? Network Utility is a software application that connects the projector and a computer to project images. Images that can be projected are computer screens and still images. The main Network Utility functions are described below: Simple 1:1 Connection Projects images by connecting the computer and projector using a wireless LAN in ad hoc mode.
3. Using the Projector via a Network 1. Insert the CD-ROM in the CD-ROM drive of your computer. 2. Specify a language. The launcher screen appears. 3. Click [PJ Network Utility Type A]. 4. Specify a destination to save the application. The "RICOH PJ NetworkUtility Type A" folder is copied to the computer. 5. To create a shortcut icon on the desktop, click [OK]. 6. Close the screen. To start Network Utility, double-click the shortcut icon on the desktop or "RICOH PJ NetworkUtility TypeA.exe" in the folder.
Projecting Images Using Network Utility 4. Double-click the "Network Utility" icon on the computer. Network Utility starts. 5. Click the [Simple 1:1 Connection] tab. 6. Select the projection method. 7. If you select [Transmit Still Image File], specify the file to be projected. 8. Click [Start]. A number appears on both the projected screen and on the computer's screen. 9. If the numbers displayed on both screens are the same, click [OK]. The computer screen or selected file is projected.
3. Using the Projector via a Network 5. Select the connected projector from [Select Projector(s) to Use (Up to 4 devices):]. If you want to manually enter the projector IP address, select [Connect by Manual Entry], and enter the IP address. 6. Select the projection method. 7. If you select [Transmit Still Image File], specify the file to be projected. 8. Click [Start]. The computer screen or selected file is projected. • To close Network Utility, either select [Exit], or click [ ] to close the window.
Projecting Images Using Network Utility 8. Press the [Network] button. CLB074 9. Insert the USB memory device into the USB port on the projector. The confirmation screen is displayed. 10. Select [OK]. The wireless LAN settings saved to the USB memory device are reflected in the projector. 11. Select [OK]. • If the conformation screen does not appear when you insert the USB memory device into the projector's USB port, remove the USB memory device. Press the [Network] button, and then reinsert the device.
3. Using the Projector via a Network 4. Select the [Network/USB Settings] menu. 5. Select [Network Settings]. 6. Select [Wireless LAN] 7. Select [Enable] in [Wireless Connection via USB] under [Simple Wireless LAN Setup]. 8. Select [Simple Connection (USB Memory)], and then press the [Enter] button. The wireless LAN settings for the projector are saved to the USB memory device. 9. Select [OK]. 10. Press the [Menu] Button. 11. Select [USB Settings]. 12. Select [OK] in [Remove Device]. 13.
Using the Projection Server Function Using the Projection Server Function The projector accesses the network server to project JPEG files saved on the server. You do not need to carry a storage device or computer that has the files to be used. Therefore, it is useful to protect information. Accessing folders on the server can be controlled by registering an access number.
3. Using the Projector via a Network Registering a URL rewrite rule Using a URL rewrite module, register a rule to rewrite "original characters" to "rewritten characters": • Original characters: ^alias name of the virtual directory/(.*) • Rewritten characters: /alias name of the virtual directory/name of the folder management file If you use IIS 7, and if the alias name is "ABC" and the folder management file name is "xyz.asp", the characters become the following: • Original characters: ^ABC/(.
Using the Projection Server Function A projected image can be controlled using the remote control. • Right arrow button ( ): Displays the next image. • Left arrow button ( ): Displays the previous image. • [Menu] button: Displays the file list while an image is being projected. 1. Turn the projector on. 2. Press the [Network] button. CLB074 3. Press the [Enter] button. The confirmation screen is displayed. 4. Select [OK]. The list of files in the root directory is displayed. 5.
3.
4. Changing the Projector Settings This chapter explains the settings on the menu screen and how to change the settings. Viewing the Menu Screen 1 2 3 4 5 6 CLB065 1. Image Adjustment menu tab Enables the image items to be adjusted and configured. For the Image Adjustment menu settings, see p.83 "Image Adjustment Menu". 2. Display Settings menu tab Enables the screen display items to be configured. For the Display Settings menu settings, see p.87 "Display Settings Menu". 3.
4. Changing the Projector Settings For the Network/USB Settings menu settings, see p.95 "Network/USB Settings Menu". 5. Display Status tab Enables information such as input signals and lamp usage time, etc., to be displayed. For item that can be displayed, see p.105 "Display Status". 6. Settings The settings and information for each menu can be displayed. For the list of possible settings for each menu, see p.79 "List of Menu Items".
Using the Menu Screen Using the Menu Screen This section explains the methods for changing the menu screen using the remote control. 1. Press the [Menu] button. CLB046 2. Select the menu tab using the [ ] and [ ] buttons. If you select the Display Status tab, you can confirm the information in this step. 3. Press the [ ] button.
4. Changing the Projector Settings 4. Select the item to be changed using the [ ] and [ ] buttons. If [To settings] is displayed on the right, the item has a submenu. Press the [Enter] button to display the submenu screen. 5. Press the [Enter] button. If [Execute] is displayed to the right of the item you select, the function is executed in this step. 6. Change the settings. The method for changing the settings depends on the item.
Using the Menu Screen • Selecting the value from a list Change the value using the [ ], [ ], [ ], and [ ] buttons, and then press the [Enter] button. • Inputting numbers Use the number buttons on the remote control to input numbers.
4. Changing the Projector Settings • Inputting text Use the keyboard that is displayed on screen to input text. You can also use the number buttons on the remote control to input numbers. • The control panel on the projector can be used for operations, but numbers for settings cannot be inputted. • A confirmation screen appears before some functions are executed or some settings are changed.
Restoring Settings to Their Default Settings Restoring Settings to Their Default Settings This section explains the method for restoring the projector settings to the default values using the remote control. 1. Press the [Menu] button. CLB046 2. Select the Default Settings menu tab, and then press the [Enter] button.
4. Changing the Projector Settings 3. Select [Reset All], and then press the [Enter] button. 4. Select [OK] in the confirm screen, and then press the [Enter] button. • The following settings cannot be reset with this function: • [User Logo] in [Display Settings] To reset the registered user logo, select [Reset Logo] in [Display Settings]. • [Password] in [Default Settings] • [Administrator Password] in [Network/USB Settings] To reset the registered passwords, contact your service representative.
List of Menu Items List of Menu Items Image Adjustment menu Item Summary Picture Mode Select the picture mode. Contrast Adjust the image contrast. Brightness Adjust the image brightness. Color Saturation Adjust the color saturation of the image. Tint Adjust the tint of the image. Sharpness Adjust the sharpness of the image. Noise Reduction Select whether or not to use the function to reduce the Y/Pb/Pr (480i/576i) or video signal noise. R-level Adjust the level of red in the image.
4. Changing the Projector Settings Item Summary Wall Color Correction Select the image hue according to the projection surface when the image is being projected on something other than a screen. Background on NoSignal Select the image display when there is no input signal. Display Help Select whether or not to display Help when there is no input signal. Display Icon Select whether or not to display icons when switching the input signals and settings.
List of Menu Items Item Summary Power On Method Select whether or not to use the auto power on function. Standby Energy Saving Select the level of energy saving while on standby. Lamp Power Select the lamp power level. High Altitude Mode Select whether or not to increase the speed of the fan. Key Lock Select whether or not to lock the buttons on the control panel. Reset All Reset all menus to their defaults. Password Register a password for the projector.
4. Changing the Projector Settings Item Summary PJLink Specify the PJLink settings. Security Specify the security settings. Projection Server Specify the projection server settings. Display Status Confirm the status of the network application settings. Display Status Item 82 Summary Input Displays the selected input signals. Resolution Displays the resolution. Frequency Displays the synchronous frequency. Sync Displays the synchronous signal polarity.
Image Adjustment Menu Image Adjustment Menu Picture Mode Select the picture mode. This function is not available when you select [On] in [3D Projection] under [Default Settings]. Default: [Standard] • Bright This image mode makes it easier to see the projection in bright locations. • Standard This is the standard image mode. • Natural Photos appear more natural in this mode. Contrast Adjust the image contrast. The greater the value, the stronger the image contrast.
4. Changing the Projector Settings • -16 to +16 Sharpness Adjust the sharpness of the image. The greater the value, the sharper the image. Default: 0 • -8 to +8 Noise Reduction Select whether or not to use the function to reduce the Y/Pb/Pr (480i/576i) or video signal noise. This function is available when you select [Y/Pb/Pr] (480i/576i) or [Video] as an input signal. Default: [Off] • On • Off R-level Adjust the level of red in the image. The greater the value, the stronger the color red is in the image.
Image Adjustment Menu • Stnd. • Full Auto Set Automatically adjust the items set for the image according to the type of input signal. This function is available when you select [Computer] as an input signal. Equalizer Select the strength of the functions that reduce the HDMI signal noise. This function is available when you select [HDMI] as an input signal. Default: [Low] • Low • High Position Adjust the values for the image position.
4. Changing the Projector Settings • 0 to +255 • Clamp Pulse 2 Adjust the clamp pulse width.
Display Settings Menu Display Settings Menu Keystone Adjust for image keystone distortion. This setting changes automatically depending on the angle of the projector position if you select [On] in [Auto Keystone] under [Default Settings]. Default: 0 • -32 to +32 Aspect Select the screen size of the image. This function is not available when you select [USB Memory] as an input signal. Default: [Normal] • Normal Display in full screen without changing the input signal aspect ratio.
4. Changing the Projector Settings • Gray • Blackboard (Green) Background on NoSignal Select the image display when there is no input signal. Default: [Logo] • Logo • Blue • None Display Help Select whether or not to display Help when there is no input signal. Default: [On] • On • Off Display Icon Select whether or not to display icons when switching the input signals and settings. Default: [On] • On • Off Start-up Screen Select whether or not to display the start-up screen when the projector is turned on.
Display Settings Menu • Reset Logo Delete the registered user logo.
4. Changing the Projector Settings Default Settings Menu Auto Input Search Select whether or not to only select inputs with signals when switching input signals. Default: [On] • On • Off Auto Keystone Select whether or not to implement keystone correction automatically depending on the angle of the projector's position. Default: [On] • On • Off Projection Mode Select the projection method according to how the projector is positioned. Default: [Stnd.] • Stnd.
Default Settings Menu 3D Projection Specify 3D projection. • 3D Projection Select whether or not to use 3D projection. The image will be slightly darker if this is set to [On]. Default: [Off] • On • Off • DLP Link Select whether or not to synchronize 3D images and DLP images. Default: [On] • On • Off • L/R Reverse Select whether or not to reverse left and right in a 3D image. Default: [Normal] • Normal • Reverse Language Select the language in which to display menus, etc.
4. Changing the Projector Settings • 4 Power Off on No Signal Select the time from the final operation to automatic power shutdown when there are no input signals. Default: [Off] • Off • 5 min. • 10 min. • 20 min. • 30 min. Power On Method Select whether or not to use the auto power on function. Default: [Manual] • Manual Turn the projector on when the [Power] button is pressed. • Auto. Automatically turn on the projector when the power cord is connected.
Default Settings Menu Default: [Stnd.] • Eco • Stnd. High Altitude Mode Select whether or not to increase the speed of the fan. The number of fan rotations is high when set to [On]. Select [On] only when using the projector at an altitude of more than 1,500 meters (4,921 feet). Do not select [On] when the altitude is less than 1,500 meters (4,921 feet). Default: [Off] • On • Off Key Lock Select whether or not to lock the buttons on the control panel.
4.
Network/USB Settings Menu Network/USB Settings Menu USB Settings You can specify how to project files from a USB device and confirm the status of the USB device. Settings • Auto Demo Select whether or not to start a slide show automatically when the projector is connected to the USB device. Default: [Off] • On • Off • Repeat Select whether or not to repeat video playback. Default: [Off] • On • Off • Display Interval (sec.) Enter the slide show switching interval from 5 to 999 seconds.
4. Changing the Projector Settings • Energy Saving IO Firmware Version Display the energy-saving IO firmware version. Network Settings Enables the wired LAN and wireless LAN settings, projector ID registration, and network status to be verified. Wired LAN Specify the wired LAN settings. • Wired LAN Settings • Transmission Speed Select the wired LAN speed. Select a speed that matches your network environment. It is recommended that [AutoNegotiation] be selected.
Network/USB Settings Menu • Subnet Mask Enter the subnet mask. Default: 0.0.0.0 • Default Gateway Enter the default gateway. Default: 0.0.0.0 Wireless LAN Specify the wireless LAN settings. • Simple Settings • Wireless Connection via USB Select whether or not to use the wireless LAN settings function using a USB memory device. Default: [Enable] • Enable • Disable • Simple Connection (USB Memory) Save the wireless LAN settings of the projector to the USB memory device.
4. Changing the Projector Settings Select the channel to use when [Adhoc] is selected. Select the channel that matches the type of wireless LAN being used. The channels available might differ depending on the country. Default: [11] For IEEE 802.11 b/g/n (2.4 GHz): 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 • Security • Authentication Method Select the wireless LAN authentication method. Only [Open System] is selectable when you select [Adhoc] in [Communication Mode].
Network/USB Settings Menu • 4 • Network Key Enter the WEP key when you select [WEP Shared Key] or [Open System] in [Authentication Method] and select [WEP] in [Encryption Method]. When using 64 bit WEP, up to 10 characters can be used for hexadecimal and up to 5 characters for ASCII. When using 128 bit WEP, up to 26 characters can be used for hexadecimal and up to 13 characters for ASCII. Enter PSK when [WPA-PSK] or [WPA2-PSK] is selected in [Authentication Method].
4. Changing the Projector Settings Select the network interface to be used. Default: [Wired LAN Priority] • Wired LAN • Wireless LAN • Wired LAN Priority Give priority to wired LAN if connected to the network via an Ethernet cable. Disconnect the Ethernet cable when using a wireless LAN. • Disable • DNS Settings • Primary DNS Server Address Enter the IP address of the primary DNS server. Default: 0.0.0.0 • Secondary DNS Server Address Enter the IP address of the secondary DNS server. Default: 0.0.0.
Network/USB Settings Menu Enter an HTTP proxy user name that is up to 31 characters. • HTTP Proxy Password Enter an HTTP proxy password that is up to 31 characters. • HTTP Server Settings • HTTP Port Enter an HTTP port that is between 0 and 65535. Default: 80 • Manage Certificate • Import Device Certificate Import the device certificate saved on the USB memory device to the projector. Insert the USB memory device into the USB port on the projector to display the file list.
4. Changing the Projector Settings • SSID Display the SSID of the connected wireless LAN network. • Authentication Method Display the wireless LAN authentication method. • Encryption Method Display the wireless LAN encryption method. • IP Address Display the IP address. • Subnet Mask Display the subnet mask. • Default Gateway Display the default gateway. • Wired LAN • Connection Status Display the wired LAN connection status. • MAC Address Display the projector's MAC address.
Network/USB Settings Menu Network Application Settings These settings enable the projection server, PJLink, etc., to be specified, and the network application status to be verified. PJLink Specify the authentication and passwords when accessing the projector using application software that is compatible with PJLink. • PJLink Authentication Select whether or not to set PJLink authentication.
4. Changing the Projector Settings Enter the root URL of the server on which the files to be projected using the projection server functions are saved. Enter up to 128 characters. • Index File Enter the name of the index file on the projection server. Enter up to 31 characters. • HTTP Proxy Server Usage Select whether or not to use a proxy server. Default: [No] • Yes • No • Access Restriction Type Select whether or not to display the access number input screen when you access the projection server.
Display Status Display Status Input Displays the selected input signals. Resolution Displays the resolution. This item appears when you select [Computer] or [HDMI] as an input signal. Frequency Displays the synchronous frequency. This item appears when you select [Computer] or [HDMI] as an input signal. Sync Displays the synchronous signal polarity. This item appears when you select [Computer] as an input signal. Signal Format Displays the Y/Pb/Pr signal format.
4.
5. Troubleshooting This chapter explains the basic problems and troubleshooting methods when an indicator light is lit. Indicator Display List The projector uses the [Power] button, indicators, and beeps to notify you if a malfunction occurs. Check the indicator's status, and implement the following measures. Indicator display image The [Power] button is located on top of the projector. The indicators are on the front of the projector. For details, see p.15 "Projector Parts and Their Functions".
5. Troubleshooting Status Causes Solutions The lamp turned off during operation, or it does not turn on • The lamp has overheated and cannot turn on. • Disconnect the power cord, wait a while, and then turn on the projector again. • The lamp's service life has expired. • The projector has malfunctioned. The lamp does not turn off. The projector has an internal malfunction. Disconnect the power cord, wait a while, and then turn on the projector again.
Indicator Display List Status "Installation Error" was displayed, and the projector turned off during operation, or it does not turn on. Causes The projector's angle is too great. Solutions Place the projector at a proper angle, and then turn it on again. • " " means the indicator is flashing.
5. Troubleshooting Common Problems If you think a malfunction has occurred, check the following before contacting your service representative. Problem Power does not turn on. Solutions • Make sure the power plug or connector is connected correctly. • Make sure the lamp cover is mounted correctly. For details, see p.117 "Replacing the Lamp". Power turns off during use. • Make sure the environment in which the projector is being used is within the acceptable temperature range.
Common Problems Problem No sound. Solutions • Press the [Input] button. For details, see p.35 "Selecting an Input Signal". • Make sure the mute function is not turned on. For details, see p.41 "Temporarily blanking the image and muting the audio". • Check the speaker's volume adjustment. For details, see p.40 "Adjusting the Volume of the Speaker". • Make sure the computer or AV equipment is connected to the projector correctly. For details, see p.28 "Connecting Equipment to the Projector".
5. Troubleshooting Problem Image is dark. Solutions • Check the settings of [Brightness] and [Contrast] in [Image Adjustment]. For details, see p.83 "Image Adjustment Menu". • Make sure the lamp is not near the end of its service life. For details, see p.105 "Display Status". • Check the settings of [RGB Input Range] in [Image Adjustment]. For details, see p.83 "Image Adjustment Menu". • Make sure [3D Projection] in [Default Settings] is set to [Off]. For details, see p.90 "Default Settings Menu".
Common Problems Problem The remote control does not respond. Solutions • Make sure the ID assigned to the remote control and in the settings of [Remote Control ID] in [Default Settings] are the same. For details, see p.90 "Default Settings Menu". • Make sure the batteries in the remote control are not dead. • Make sure the batteries are correctly loaded into the remote control. For details, see p.21 "Loading Batteries into the Remote Control". • Make sure the remote control is inside its effective range.
5. Troubleshooting Problem Wireless LAN is disabled. Solutions • Check the settings of [Wireless LAN Settings] in [Network Settings] under [Network/USB Settings]. For details, see p.96 "Network Settings". • Make sure there is nothing placed between the computer and the projector. • Make sure the operating system of the computer is compatible with Network Utility. Log in to the computer using administrator privileges to configure the wireless LAN settings using Simple 1:1 Connection or a USB memory device.
6. Maintenance This chapter explains the operating precautions and maintenance for the projector. Operating Precautions Pay attention to the following points when using the projector: • If moving the projector under conditions including vibration and shock, use both the packing case and included carrying bag. Transporting the projector using the carrying bag only may damage it due to shock or vibration.
6. Maintenance Cleaning the Projector • Do not remove any covers or screws that are not mentioned in this manual. There are high voltage components inside the product that may cause electric shock. Contact your service representative if any of the product's internal components require maintenance, adjustment, or repair. • Do not disassemble or modify the product. Doing so may cause injury or malfunction. • When performing maintenance on the machine, always disconnect the power cord from the wall outlet.
Replacing the Lamp Replacing the Lamp • Before replacing the lamp, turn off the power and wait at least one hour to allow the product to cool completely. If it is not completely cool, you may burn or injure yourself due to the inside of the product and lamp unit being hot. If you replace the lamp without unplugging the power cord from the power outlet, electric shock or explosion may occur. • Be careful when handling the used lamp so that it does not break. If it breaks, it may cause injury.
6. Maintenance 2. Turn the knob counterclockwise, and then open the lamp cover. CLB059 3. Raise the metal handle. CLB061 4. Hold the handle, and then pull the lamp unit out of the projector.
Replacing the Lamp 5. Insert a new lamp unit. CLB060 Make sure that the small projections inside the projector are inserted into the holes of the lamp unit properly. 6. Close the lamp cover. Correctly install the outer lamp cover. Incorrect installation may prevent the lamp or projector from turning on. 7. Reset the lamp time. For the reset method, see the manual provided with the lamp. • The lamp's service life can be verified using [Lamp Time] in [Display Status].
6. Maintenance Managing the Projector Using Projector Management Utility Projector Management Utility conforms to the PJLink class 1 standards, and is compatible with all class 1 commands. A maximum of 100 projectors connected to the network can be managed using one computer. Projector Management Utility operating environment is described below.
Managing the Projector Using Projector Management Utility • To uninstall Projector Management Utility, use the program delete function in [Control Panel] to delete "Projector Management Utility". Settings Required to Use Projector Management Utility Prepare the network so the projector can be connected. Specify the settings either in [Wireless LAN] or [Wired LAN].
6. Maintenance • Depending on the setting in [Standby Energy Saving], the projector does not respond even if the projector is in standby mode. Press the [Power] button, or change the setting in [Standby Energy Saving]. • If a communications error prevents the projector from being detected, "?" is displayed. If the connection failed due to an incorrect password or other reason, "×" is displayed.
Consumables Consumables • Lamp unit Replacement Lamp Type 3 • Contact your sales or service representative for information about consumables.
6.
7. Appendix This chapter explains the projector's specifications and compatible signals. This chapter also explains where to inquire about the projector and related services. Specifications Specifications for the Projector Component Specifications Power consumption 300 W or less Weight Approx. 3.0 kg (6.7 lb.) External dimensions (not including 257 × 144 × 221 mm (10.1 × 5.7 × 8.
7. Appendix Component Connection ports Specifications • COMPUTER In port Mini D-SUB15 × 1 • HDMI port (HDCP compliant)* HDMI × 1 • Video In port RCA_1pin × 1 • Audio In port Mini Jack × 1 • Control port USB-TYPE-minB × 1 • USB port TYPE-A × 1 USB 2.
List of Compatible Signals List of Compatible Signals Set the computer and AV equipment output signals so that they match the input signals compatible with the projector. If resolutions or signal frequencies that are not compatible with the projector are input, the image may flicker or become blurred. Further, the image may not be displayed. • Images with a resolution greater than 1280 × 800 are compressed when displayed, so some of the information may be lost or the image may deteriorate.
7. Appendix Resolution Mode 1024 × 768 1024 Vertical (pixel) 768 Vertical (Hz) Horizontal (kHz) Clock (MHz) 60.004 48.363 65.000 70.069 56.476 75.000 75.029 60.023 78.750 84.997 68.678 94.500 74.700 60.134 79.857 1152 × 864 1152 864 75.000 67.500 108.000 1152 × 870 1152 870 75.062 68.682 100.001 1280 × 720 1280 720 60.000 45.000 74.250 59.995 47.396 68.250 59.870 47.776 79.500 74.893 60.289 102.250 84.837 68.633 117.500 59.910 49.306 71.000 59.
List of Compatible Signals Resolution Frequency Mode Horizontal (pixel) Vertical (pixel) 1366 × 768 1366 768 1400 × 1050 1440 × 900 1400 1050 1440 900 Vertical (Hz) Horizontal (kHz) Clock (MHz) 60.000 48.000 72.000 59.790 47.712 85.500 59.948 64.744 101.000 59.978 65.317 121.750 74.867 82.278 156.000 59.901 55.469 88.750 59.887 55.935 106.500 74.984 70.635 136.750 84.842 80.430 157.000 1600 × 900 1600 900 60.000 60.000 108.000 1600 × 1200 1600 1200 60.
7. Appendix Resolution Frequency Mode Horizontal (pixel) Vertical (pixel) Vertical (Hz) Horizontal (kHz) Clock (MHz) 720 / 60p 1280 720 60.000 45.000 74.250 1080 / 50i 1920 540 50.000 28.125 74.250 1080 / 60i 1920 540 60.000 33.750 74.250 1080 / 50p 1920 1080 50.000 56.250 148.500 1080 / 60p 1920 1080 60.000 67.500 148.500 Video Input Mode Frequency Vertical (Hz) NTSC 59.940 PAL 50.000 SECAM 50.000 PAL-M 59.940 PAL-N 50.000 PAL60 59.940 NTSC4.43 59.
List of Compatible Signals Resolution Frequency Mode Horizontal (pixel) Vertical (pixel) Vertical (Hz) Horizontal (kHz) Clock (MHz) 480p (525p) 720 483 59.940 31.469 27.000 576p (625p) 720 576 50.000 31.250 27.000 720 / 50p 1280 720 50.000 37.500 74.250 720 / 60p 1280 720 60.000 45.000 74.250 1080 / 50i 1920 540 50.000 28.125 74.250 1080 / 60i 1920 540 60.000 33.750 74.250 1080 / 24p 1920 1080 24.000 27.000 74.250 1080 / 30p 1920 1080 30.000 33.750 74.
7. Appendix Resolution Mode 1024 × 768 1024 Vertical (pixel) 768 Vertical (Hz) Horizontal (kHz) Clock (MHz) 60.004 48.363 65.000 70.069 56.476 75.000 75.029 60.023 78.750 84.997 68.678 94.500 74.700 60.134 79.857 1152 × 864 1152 864 75.000 67.500 108.000 1152 × 870 1152 870 75.062 68.682 100.001 1280 × 720 1280 720 60.000 45.000 74.250 59.995 47.396 68.250 59.870 47.776 79.500 74.893 60.289 102.250 84.837 68.633 117.500 59.910 49.306 71.000 59.
List of Compatible Signals Resolution Frequency Mode Horizontal (pixel) Vertical (pixel) 1366 × 768 1366 768 1400 × 1050 1440 × 900 1400 1440 1050 900 1600 × 900 1600 900 1680 × 1050 1680 1050 Vertical (Hz) Horizontal (kHz) Clock (MHz) 60.000 48.000 72.000 59.790 47.712 85.500 59.948 64.744 101.000 59.978 65.317 121.750 74.867 82.278 156.000 59.901 55.469 88.750 59.887 55.935 106.500 74.984 70.635 136.750 84.842 80.430 157.000 60.000 60.000 108.000 60.
7. Appendix Specifications for Ports Computer In Port Pin assignment 11 6 15 10 1 5 CLB064 Pin description Pin No. 134 During RGB input During Y/Pb/Pr input 1 Video signal (R) Color difference signal (Pr) 2 Video signal (G) Luminance signal (Y) 3 Video signal (B) Color difference signal (Pb) 4 N.C 5 GND 6 GND (R) GND (Pr) 7 GND (G) GND (Y) 8 GND (B) GND (Pb) 9 N.C 10 GND 11 N.
Specifications for Ports Input Signal • RGB input RGB signals: 0.7V (p-p), 75 Horizontal sync signal: TTL level (Pos/neg polarity) Vertical sync signal: TTL level (Pos/neg polarity) • Y/Pb/Pr input Y signal: 1.0V (p-p), 75 Pb/Pr signals: 0.7V (p-p), 75 Control Port Interface format Communication method RS-232C, 115,200bps, No Parity, Data Length: 8 bits; Stop Bit Length: 1bit Communication format #(23h)’ + Command + CR (0Dh) Only 1 command valid per communication.
7. Appendix Command Acknowledge (Normally ended) * Icon display on ICN:1 =ICN:1 Icon display off ICN:0 =ICN:0 PAT =PAT:SC0 Status display on DON =DON:SC0 Status display off DOF =DOF:SC0 RGB input INP:1 =INP:1 Y/Pb/Pr input INP:2 =INP:2 HDMI input INP:5 =INP:5 Video input INP:9 =INP:9 Network input INP:12 =INP:12 USB input INP:13 =INP:13 Item Auto setting (RGB input) * CR is added to the end of "Acknowledge (Normally ended)".
Copyrights Copyrights This product uses open source and/or third party software. To check the information about software copyrights, see the documents in the "Copyrights" folder on the supplied CD-ROM.
7. Appendix Where to Inquire Contact your sales or service representative for further information about topics covered in this manual or to inquire about topics not covered in this manual.
Trademarks Trademarks Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. DLP is a registered trademark of Texas Instruments. DLP Link is a trademark of Texas Instruments. HDMI and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
7.
INDEX 3D Projection.........................................................91 A AC In socket...........................................................17 Accessories............................................................13 Ad Hoc mode........................................................58 Adjustable feet................................................16, 36 Adjusting for keystone distortion..........................39 Adjusting the focus................................................
F L Fan Error..............................................................107 Focus......................................................................38 Focus lever.......................................................16, 38 Folder management file........................................67 Freeze button...................................................18, 42 Frequency............................................................105 Front view.............................................................
P Page button............................................................18 Password................................................................93 Pausing the image.................................................42 PDF manual..............................................................9 Picture button...................................................18, 43 Picture Mode.........................................................83 PJLink...........................................................
Volume button.................................................18, 40 W Wall Color Correction..........................................87 Where to inquire.................................................138 Wired LAN......................................................55, 96 Wireless LAN..................................................57, 97 Z Zoom button....................................................
EN GB EN US EN AU Y0127511 © 2011
