User manual WLAN Module: R-1FJ 2019/10/20
The revision history of the product specification Issued Date Revision Code Revision Page Oct.20.
Contents 1 2 3 4 5 6 7 8 Scope .................................................................................................................................................................... 4 Part Number .......................................................................................................................................................... 4 Dimensions, Marking and Terminal Configurations ...............................................................................................
1 Scope This specification is applied to the IEEE802.11b/g/n W-LAN. - Module size - IC/Firmware - Interface - Reference Clock - ROM - Weight 2 Part Number Sample Part Number LBEE5ZZ1FJ-957 :21.0 x 10.0 mm typ., t = 2.0 mm max. :Broadcom BCM4343W :SDIO :37.4MHz Crystal Oscillator embedded 32kHz LPO embedded :Internal OTP :0.
3 Dimensions, Marking and Terminal Configurations Dimensions Unit:mm FPC connector Maker: ヒロセ P/N: FH35C-23S-0.
Terminal Configurations Terminal Name 1 VBAT 2 VBAT 3 Temp 4 VIO 5 GND 6 7 8 WL_REG_ON 9 10 WL_HOST_WAKE 11 GND 12 13 14 15 16 GND 17 SDIO_D0 18 SDIO_D1 19 SDIO_D2 20 SDIO_D3 21 SDIO_CMD 22 GND 23 SDIO_CLK 1 2 Pin Type VDD VDD VIO VIO VIO SDIO SDIO SDIO SDIO SDIO SDIO I/O PI PI PO PI PI PO I/O I/O I/O I/O I/O I 23 22 Description Battery voltage input Battery voltage input Thermistor Output SDIO I/O and Digital I/O supply GND WiFi Power ON/OFF(WiFi RESET) WiFi Interrupt GND GND SDIO data line 0 SDIO
SDIO Pin Description No.
4 Rating min. max. unit Storage Temperature -30 +70 deg.C VBAT -0.5 6.0 V Supply Voltage VDDIO -0.5 +3.9 V Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. No damage assuming only one parameter is set at limit at a time with all other parameters are set within operating condition. 5 Operating Condition min. -30 -10 3.0 1.
7 Mechanical performance and environmental performance No. 1 Items Vibration test in packed state Specifications No severe damages No problem for communication Test Methods Frequency : 10 to 100 Hz Grms:1.
8 Packing The products shall be packed in the tray as shown blow. Number of the products in the carton is 1092. There is the78pcs per tray and 14 pile number of the tray which stored the product. A dummy tray is putted on the topmost part of trays.
The package with 4 cartons as below shall be shipped. The packing unit is 4368pcs. Internal Box Shipping Box Please save below 40 degrees C in packaging, because there is a risk of deformation of the tray.
Module Integration description 1. List of applicable FCC rules This device complies with part 15.247 of the FCC Rules. 2. Summarize the specific operational use conditions This module can be used in printer . The input voltage to the module should be nominally 3.0~3.6 VDC, typical value 3.3VDC and the ambient temperature of the module should not exceed 85℃. This module using only one kind of antennas. The antenna is not field replaceable.
complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Frequency spectrum to be investigated For host products with certified modular transmitter, the frequency range of investigation of the composite system is specified by rule in Sections 15.33(a)(1) through (a)(3), or the range applicable to the digital device, as shown in Section 15.
NOTICE - Please use our product after enough consideration including the heat radiation, because it may become the high temperature. 1 Storage Conditions Please use this product within 6month after receipt. - The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH. (Packing materials, in particular, may be deformed at the temperature over 40deg.C.
CAUTION PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS. Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications of our product when our product is mounted to your product. All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment specified in this specification.
ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence.