SPECIFICATIONS DISASSEMBLING MAJOR COMPONENT PARTS Flash ass'y.. 5. Viewfinder unit. 6. 1. 8. 9. Bottom cover Front cover... Top P lever plate ass’ R gear base plate ass’y.. ‘Winding plate SAE NNN ASSEMBLING . P lever plate ass’y . S gear hold u.. . Viewfinder u. . Flash ass'y. . Top cover... . Front cover . Bottom cover . W-R changing plate 7 . Winding plate B . Winding plate R gear base plats INDEX ADJUSTMENT 1. Lens Focus adjustment. 2. AE adjustment 3. FM SCHEMATIC DIAGRAM ...cnveuveeen.
Type: 35mm lens electronic shutter type Lens: 35mm color Nondrinker f4.0 lens, 3 elements, 3 groups. Focusing: By zone-focus marks from 1.0m to infinity Shatter: Programmed type electronic shutter, 1/30 — 1/500 sec. Self-Timer: Built-in electronic type. Operating delay of approx. 10 sec. Viewfinder: Reverse Galilean viewfinder Magnification 0.53%, Field of view 80%. Exposure Adjustment: With CdS photocell, Exposure Coupling Range EV9 ~ EVE (ISO 100) Film Speed Range: 1SO 100 1000.
DISASSEMBLING OF MAJOR COMPONENT PARTS 1. Bottom cover (Fig. 1) (1) Open the Battery cover (No. 13). then take off the Screw (No. 7). (2y Take off five Screws (No. 8,9, 10). (3} Remove the Bottom cover (No. 11). 2. Front cover (Fig. 1) (1) Take off two Screws (No. 5). (2) Take off two Screws (No. 4} and the Patron holder (No. 12). (3) Remove the Front cover (No. 6). 3. Top cover (Fig. 1) {1) Take off the screw (No. 1). £2) Remove the Top cover (No. 2). {3) Remove the Release button (No. 3).
4. Flash ass'’y (1) Remove the Blue lead wire shown in Fig. 2. (2) Remove five Lead wires (Pink, Yellow, Green, Red. Black) shown in Fig. 3 (3) Take off the Screw (Fig. 2 No. 1}, and two Screws (Fig. Remove the Flash ass’y. §. Viewfinder unit (1) Remove the Capacitor on the Power supply FPC from the Viewfinder frame. (Fig. Remove the Self LED on the AE FPC from the Viewfinder frame (Fig. Remove the soldering portion shown in Fig. Take off two Screws and Remove the Holder plate Remove the Winding signal.
. Shatter (10) an 12) Take off the Screw and remove the Flash plate (P. 28 No.36). Remove the Spring (No. 2) from the SW Lever (No. 1) shown in Fig, 6. Take off two Screws (No. 3, 4) shown in Fig, 6. Remove the 8. gear hold u. (No. 3) shown in Fig. 6. Note: Do not bent contacts. Remove the S. set lever (Fig. 18 No. 3), the S set cam (Fig. 18 No. 2), and the Sprocket (Fig. 18, No. 1}. Detach the soldering of two Lead wires (Blue, Red) from the P Mg. shown in Fig. 7.
7. P lever plate ass'y (1) Detach the soldering of two Lead wires (Blue, Black) from the Motor shown in Fig. 4. (2) Take off two Screws and remove the P lever plate says (P.28 No. 41). (3) Remove the P lever ass’y (P. 28 No. 40). 8. R gear base plate ass’y (1) Take off three Screws and the Screw (FP. 26 No. 20). (7) Remove the R gear base plate says 26). (3) Remove five gears 30). 9. Winding plate (1) Take off three Screws Remove the Winding plate Remove the Winding 5th. gear and the Winding 6th gear 12).
ASSEMBLING 1. W.R changing plate Clean up both contacts on the W-R changing plate (Fig. 12, No. 6) and the Changing lever ass’y (Fig. 12, No. 5). Put the Wind set button (Fig. the Body. Set the Changing lever ass’y (Fig. the Body. Set the Set lever ass’y (Fig. 13. No. 4) and the Shaft: Set lever (Fig. 13 No. 3). Set the Changing lever plate (Fig. 12, No. 3) and tighten two Screw (Fig. 12.No. 1,2). Set the Spring (Fig. 12, No. 4).
2. Winding plate B (Fig. Set the Spool gear (No. 6) to the Motor shaft (No. 9). Set the Winding 6th gear B (No. 5). Set the S. Ist gear (No. 7). Set the Shaft: S 2nd gear (No. 8}. When assembling the other side of the Shaft, hold ® part with Pliers and fix the § gear 3rd with the Screw Set the Winding stop lever (No. 4), and the Spring (No. 3). Set the Winding plate B (No. 2) with two Screws (No. 1). Fig.
3. Winding plate (Fig. Set the Winding Ist gear {No. 12), the Ist lever ass’y (No. 11) and the Plate: W. Ist gear (No. 10} with the Screw (No. 9). Fix the Spring (No. 13} between @® and ®. Fix the Set lever spring (No. 14). Set the Winding 6th gear A (No. 6). Set the Winding 3rd lever ass’y (No. 8). Set the Winding 5th gear (No. 7) to the Winding plate {No. 5) and set these parts on the Body with three Screws (No. 4). Note: © portion comes out form @ hole. Set the Return lever (No.
4. R gear base plate ass’y (1) Set five gears 30}. (2) Set the R gear base plate ass’y with four Screws {P. 26 No. 19,20). 5. P lever plate ass’y {1} Set the P lever plate says with two Screws 44). 2) Set the FPC as shown in Fig. 7.
IJ J 6. Shutter (1) Set the Shutter ass’y to the Body with four Screws shown in Fig. 11. (2) Set the P. plate: wind the Shutter with the Screw Set the Spring (No. 1) to the portion of the Shutter (No. 2) shown in Fig. 16. (4) Solder two Lead wires (Red, Blue) from the P Mg. shown in Fig. 7. {5} Solder the Lead wire (Red) shown in Fig. 8. (6) Set the AE FPC on the Tool (31369997) first, then set the P FPC on it. (Fig. 17). (7) Solder nine portions with care. Tool: 3136 9997 Fig.
7. S. gear hold u. (Fig. 18) (1} Put the Sprocket (No. 1} on the Body. (2) Putt Hes set cam (No.2) on the Body. @® Part parallels the Body. (3) Put the S set lever (No. 3) on the Body. Part comes right side of the Shutter lever pin. (4) Put the S gear hold u. (No. 4) with two Screw (No. 3). Note: Clean up the contacts before assembling. {5) Set the spring to the SW. lever shown in Fig. 6. {6) Put the Flash plate with the Screw (P. 28 No. 37).
I) J 8. Viewfinder U. (1) Put the Winding signal roller ass'y the Body. (2) Put the Viewfinder Unit on the Body with four Screws (No. shown in Fig. 5. Note: Put the C2 gear shaft correct way as shown in Fig. 18-A. (3) Put the Winding signal (P. 28 No. 26). (4) Solder the portion (No. 1) shown in Fig. 5. (5) Put the Plate with two Screws (P. 28 No. 43). Note: Clean up the Contact before assembling. (6) Put the Capacitor on the Power supply FPC (No. 1) and the Self LED (No.
9, Flash ass’y (1} Put the Flash printed board ass'y with the Screw {P. 28 No. 69). (2) Put the Flash case ass’y with two Screws. (Fig. 3 No. 1,2} (3) Solder the Lead wires shown in Fig. 3. (4) Arrange the Lead wires as shown Fig. 19. Fig.
10. Top cover (Fig. I} {1) Put the Release button (No. 3). Note: Pay attention with direction of the Release button. {2) Put the Top cover (No. 2) with the Screw (No. 1). 11. Front cover (1) Put the AE FPC holder the bottom part of the Body. 2) Set the Parts on the Shutter ass’y as follow (Fig. 20). @ Focusing lever (No. 1) Middle click position, @ 1SO lever (No. 2) «eo ISO 100 position {Push to arrow direction). (® Fixed focus lever (NO. Fixed focus position (Push to arrow direction).
ADJUSTMENT Three click position 1. Lens Focus Adjustment (Fig. 21) * Remove the Batteries at first. (1) Release the Shutter by pushing the Lever (No. 1) to arrow direction. (2) Set the Focus lever (No. 2) on middle click position { 2.5m). (3) Push the Lever (No. 3) to arrow direction to open the Shutter. Note: Dao not deform the Spring. (4 Loosen the Screw (No. 4) and turn the Lens to adjust the Focusing with mn, -15.0 = 0.5 mm with f= 193.5 mm millimeter 2.
3. FM adjustment (Fig. 23) * Remove the Batteries at first. {1} Release the Shutter by pushing the Lever (No. 1) to arrow direction. {2} Push the Lever (No. 2) to arrow direction to pop up the Flash. Three click position (3) Set the Focus lever (No. 3) to the & position. (Left side click). (1.2m) (2.5m) (os) (4) Set the ISO plate (No. 5) to the ISO 1000 position. Note: When adjusting, keep ® part of the Lever (No. 3) to the arrow direction. {5) Push the lever (No.
SCHEMATIC DIAGRAM VE BARRIER SW SELF. SW. 1 tom swt | Loy RELEASE SW. 02 BACK COVER SW. @ Oo TRIGGER SW. COUNTER SELF LED Sw. RE FLASH UNIT @ CdS! OFF FLASH SW.
A SEAR | panto. Description SKI | part No. Description Sth | Part No. Description o 3139 1141 Self button 25 09841630W Screw M1.6x 3.0 @ 3139 1138 Counter window @® 3139 1151 Barrier guide @ 3139 1139 W. Indicator window & 3136 1144 Barrier lever @® 3139 1142 Self contact @ 3139 1152 Barrier ® 09841625W | Screw M1.6x2.5 @ 3116 1683 Retaining ring ® 3139 1143 Self spring @ 3136 1146 Spring @-O | 3139 1037 Top cover says | 3139 1035 Barrier ass'y 8 09841635W | Screw M1.6x3.
y oy B Skate Part No. Description Sheen Part No. Description Sketch Part No, Description 1 3136 1039 Spool 2 3136 1325 Film label 3 3136 1311 F. detector pin 4 3136 1253 Sprocket 5 3136 1255 S. set fever 6 02514025W | Screw M1.4x2.5 7 3136 1251 S. 3rd gear 8 09842025W | Screw M2.0x2.5 9 3139 1034 Motor ® 3136 1026 F. detector lever @ 3136 1310 F. detector lever spring @ 3116 1683 Retaining ring ® 09851630W | Screw M1.6x 3.0 @ 3136 1094 F. detect P.C.B.
Part No. Description Sh | part vo. Description Ske | pan No, Description 3116 1683 Retaining ring B® 3136 1287 Rewinding | Ith gear 3136 1297 MR lever B-B | 3136 1073 Rewinding base plate ass’y 3136 1304 MR lever 7 3136 1286 Rewinding {0th gear. 09831640W | Screw M1.6x4.0 28 3139 1285 Rewinding 8th gear. 3136 1232 Winding plate 29 3116 1284 Rewinding 7. 9th gear. 3136 1003 W. 3rd lever says 30 3136 1283 Rewinding 6th gear, 3136 1237 W. 5 gear 3 3136 1296 Set lever shaft 09851645W { Screw M1.6x 4.
D Sketch | part No. Description Sketch | part No. Description SRI | part No. Description @ 3136 1684 Release contact C 38 3139 1092 3136 9011 Diode @ | 3136 1682 | Release contact A 39 | 09851625W | Screw Mi 6428 § | 3136 9008 | Transistor © | 3136 1685 | Insulator waves tos | Overpass 4-6 | 3139 1411 | Flash says ® 3136 1683 Release contact B 41 3139 1079 P lever plate oy 9 09851635W | Screw M1.6x3.5 | 3136 1085 Counter base plate ass’y 42 3139 1091 Power supply FIC a 18 | 09842040W | Screw M2.0x4.
E SKE | pea. Description Seth | Part No. Description SK | part No, Description i D2I516060W | Screw M1.6x 6.0 2 3136 1306 P. plate: wind 3 3136 1030 SW.
