INDEX SPECIFICATIONS 11, ASA contact holder says. 1. PURPOSE OF TABLE MAT wo 3 12. Soldering of lead wires.. 2, TOOL SET FOR X-6, 4 13. Film counter 3. DISASSEMBLING OF MAJOR COMPONENT PARTS base plate says 1. Finder COVER 5 15. 2. BOUDOIR COVER base plate says .. 17. 4, Film counter says 5. ADJUSTMENT 5. ASA contact holder says 6. SPD circuit board says WIRING DIAGRAM... 1. SCHEMATIC DIAGRAM 8. SKETCH INDEX AND PARTS LIST A. Top and front parts B. View finder and film counter parts C.
SPECIFICATIONS 35 mm SLR with automatic electronic exposure control focal plane shutter FILM FORMAT AND FRAME SIZE .. 35 mm film; LENS MOUNT. K mount STANDARD LEN! 50 mm XR NONDRINKER {71.4 30 mm XR NONDRINKER {1.7 NONDRINKER /2.0 Electronically controlled, vertically moving metal focal plane shutter Automatic from 16 to 1/1000 sec. Manual from 16 to 1/1000 sec.
PURPOSE OF TABLE MAT It is necessary to discharge static electricity in and around the work table including the operator in order to protect IC or printed circuit boards from destruction by electrostatic charge. For this purpose, a conductive table mate (ground mat) should be put on the work table and the operator should wear a wrist band which is connected to the table mat.
2. TOOL SET FOR X-6, 7 Sketch No. | Tool No. Description XR7 | X-6 [XREFS |XR2S | KR.10 | KR-5 1 | Tool for Winding Lever Nut (Sketch No. 4 on page 31269998 | Tool for Storing Pliers (Sketch No. 41 on page 31169996 | Tool for Synchrony Socket (Sketch No. 33 on page 31169995 | Tool for Tool Shaft 31269997 | Tool for 45° Adjustment Mirror (Fig.
CC o I. DISASSEMBLING OF MAJOR COMPONENT PARTS I. Finder cover (see Fig. Take off the SCREW (No. I) and remove the COVER: WIND LEVER (No. 2). Take off the SCREW (No. 3) and remove the WIND LEVER (No. 4). Remove the NUT (No. 5). Take off three SCREWS (No. 9) and remove the SHUTTER SPEED PLATE (No. 6) carefully. Take off three SCREWS (No. 7) and remove the SHUTTER SPEED DIAL (No. 8). Remove the REWINDING DISK (No. 13). Remove the RETAINING RING (No. 14). Remove the ASA DIAL (No. 18). Take off five SCREWS (No.
3. SD base plate says (see Fig, 2) * 1) Take off two SCREWS (No. 3). 2) Take off the SCREW (No. 5). 3) Take off the SCREW (sketch No. 29 on page 38). 4) Remove the SD BASE PLATE SAYS (No. 2) carefully. NOTE: Pay attention not to bend the contacts and not to lose the SPRING {No. 4). 5) Remove the SPACER (No. 1). 4. Film counter says (sketch No, 36 on page 38) 1) Remove the WASHER (sketch Nd. 35 on page 38). 2) Take off two SCREWS (sketch No. 29 on page 38). 3) Remove the FILM COUNTER. . S.
CL i] 6. SPD circuit board says (sketch No. 24 on page Detach the soldered portions of all LEAD WIRES shown in Fig. 4. Take off two SCREWS (sketch No. 25 on page 38), and remove the SYNCHRONY BASE PLATE (sketch No. 26). Take off two SCREWS (sketch No. 44 on page 40). Remove the EYE PIECE FRAME (sketch No. 43) and the SHIELD PLATE (sketch No. 17 on page 38). Take off two SCREWS (No. 1} shown in Fig. 5. Detach seven soldered portions of SPD CIRCUIT BOARD SAYS shown in Fig. 6.
7) Take off two SCREWS Nos. 1 and 2 shown in Fig. 7. 8) Take off three SCREWS shown in Fig. 8. 9) Move the SPD CIRCUIT BOARD SAYS with care as shown in Fig. 9. NOTE: Do not pull up A and B portions of the SHEET (shown in Fig. 10) as shown in Fig. 21. 10) Take off two SCREWS (No. 1) shown in Fig. 11. 11) Remove the PRISM COVER (No. 2) and the PRISM (No. 4). 12) Take off three SCREWS (No. 5) and remove the PRISM FRAME SAYS (No. 6) carefully, Fig. 8 Fig.9 Fig.
Fresnel lens (see Fig. 11) 1} Take off three SCREWS (No. 9). 2) Remove the FRESNEL HOLDER (No. 8) and the SHIELDS (No. 10). 3) Remove the FRESNEL LENS (No. 7). 8. Mirror box (see Fig. 12) 1) Peel off both FRONT LEATHERS (sketch Nos. 5, 43 on page 42). 2) Take off two screws (No. 3) and remove the SELF LED COVER (No. 2). 3) Take off four SCREWS (No. 1) and remove the MIRROR BOX SAYS. 4) Take off three SCREWS (No. 4) and remove the MIRROR BOX with care. 9. Mirror frame says (see Fig.
10. Winding shaft (see Fig. Take off the SCREW (No. 1) (Turn clockwise) and remove the WINDER CONNECTION SHAFT (No. 2). Detach the soldered portion of purple LEAD WIRE (No. 11). Take off three SCREWS (No. 8, 9) and remove the WIND CONNECTION LEVER GUIDE SAYS (No. 10). Remove the WIND RATCHET SAYS (No. 3). Take off two SCREWS (No. 4) and remove the WIND SHAFT BUSH (No. 5). Remove the REWINDING SPRING (No. 6) and the BUSH (No. n. Pull up the WINDING SHAFT (sketch No. 33 on page 40).
ASSEMBLING 1. Mirror box (see Fig. Set the STOPPER RUBBER (No. 8). Hook the SPRING (No. 10). Set the SPRING (No. 4) to the Q SET LEVER SAYS (No. 3) and insert it into the Q SET LEVER SHAFT (No. 6). Fix the RETAINING RING (No, 7). Set the RELEASE LEVER SAYS (No. 1) and fix the RETAINING RING (No. 5). Hook the SPRING (No. 2). Set the Mg BASE PLATE (No. 1 in Fig. 16) and tighten two SCREWS (No. 2). ’ Hook the RELEASE LEVER SPRING (No. 4). Tighten the SCREW (No. 3). Set the Q SET LEVER (No.
2. Winding shaft (see Fig. Insert the BUSH (No. 2) in the WINDING SHAFT (No. 1). Insert the REWINDING SPRING (No. 3) in the WINDING SHAFT (No. 1) as shown in Fig. 17. Turn the WINDING SHAFT (No. 1) and set the position of the REWINDING SPRING (No. 3) as shown in Fig. 17. Fix the REWINDING SPRING (No. 3) in the BUSH (No. 4) and tighten two SCREWS (No. 5). Turn the WINDING SHAFT (No. 1) to the clockwise about one rotation and set the WIND RATCHET SAYS (sketch No. 13 on page 42).
Wind connection lever guide says (see Fig. 18) * 1) Hold the LEVER (No. 10) up and align the SCREW (No. 7) holes. 2) Bring the LEVER (No. 1) to the stitch line (No. 2) from the shutter side. 3) Insert the WIND CONNECTION LEVER GUIDE SAYS so that the LEVER (No. 3) does not protrude from (No. 4} and (No. 5) can get in the LEVER (No. 6). ’ 4) Tighten three screws (No. 7, 8 and 9) NOTE: } . Detailed drawing of (No, 4) shows that the LEVER (No. 1) and the LEVER (No. 3) are engaged. : 4.
5. Fresnel lens (see Fig. 20) 1) Check the scratch and the stain on the FRESNEL LENS (No. 2). 2) Set the FRESNEL LENS on the PRISM FRAME (No. 1) as shown in Fig. 19, } 3) Fix the A portion of the FRESNEL HOLDER (No. 3) in the B portion of the PRISM FRAME (No. 1) and tighten three SCREWS 4) Attach the SHIELDS (No. 5). 6. Bending of SPD circuit board says (see Fig. 21) «Bend it round, not sharply. «The thick line in the figure shows turning up.
7. LCD (sec Fig. 22) 1) Glue the LED PRISM (No. 7). 2) Clean up both side of LCD (No. 1) and DISPLAY PART (No. 2) shown in Fig. 22. 3) Glue the underside of B portion of LCD (No. 1). 4) Place A portion of LCD (No. 1) in A” portion of PRISM FRAME (No. 6) and B portion to B’ with care. NOTE: Do not pull up the SHEET (No. 4) in the arrow direction as shown in Fig. 23. 5) Set the SHEET HOLD PLATE (No. 3) to the PRISM FRAME (No. 6) and tighten two SCREWS (No. 5).
Prism frame says (see Fig. Fix all LEAD WIRES (Nos. 1, 2 and 3) as shown in Fig. 24. Hold A portion of the PRISM FRAME (No. 4) and set to the underside of B portion for the first time. NOTE: . (i) Pay attention not to break the SPD circuit board says. (i) When the arrow portion of the mirror box (see Fig. 25) is bent, the PRISM FRAME (No. 6) can not place in the mirror box. After confirming the position of the prism frame, tighten three SCREWS (No. 5).
10. SPD circuit board says When repairing of SPD circuit board says, use the static control! mat. ASA RESISTOR PLATE SIDE. 1) Arrange two LEAD WIRES (blue and orange) along the prism cover shown in Fig. 28. 2) Bead the SPD CIRCUIT BOARD SAYS at A-A" portion and assemble it as shown in Fig. 29. 3) Set the LED (red) (No. 1) into the sheet hold plate shown in Fig. 29. 4) Turn the ASA RESISTOR PLATE and assemble it as shown in Fig. 30. 5) Tighten three SCREWS (No. 2) shown in Fig.
SHUTTER RESISTOR PLATE SIDE (see Fig. Fix BLACK LEAD WIRE between the body and the shutter as shown A portion in Fig. 31 and set it along the Prism cover. Set the FPC (No. 3) to B portion of the SPD circuit board says. Move the SHUTTER RESISTOR PLATE (No. 4) in the arrow direction and set it on the FPC (Y portion to Y’ and Z portion to z). Tighten the SCREW (No. 1) and the SCREW (No. 2). Fix D portion under the C portion as shown in Fig. 31A. Insert the SPD in the SPD WINDOW (No. 2) shown in Fig.
11. ASA contact holder says 1) Make sure the contacts of the ASA CONTACT SAYS (No. 3) and the BLC CONTACT SAYS (No. 2) shown in Fig. 35. 2) Assemble them to the rewind shaft carefully. 3) Assemble the ASA CONTACT HOLDER SAYS (No. 1) and White © Blue 5 Yell E Yellow green tighten the SCREW (No. 4). 2 oto 8 eh 12. Soldering of lead wires ’ © Orange Green 1) Solder lead wires of the SPD circuit board says as shown in Fig. Fix BLACK LEAD WIRE to the synchrony base plate as shown in ® ® Fig. 37. .
13. Film counter (see Fig. Adjust the CAM portion (A) of the GEAR A SAYS on the line B shown in Fig. 39. 2) Set the WIND SHAFT A SAYS to the film counter as shown in Fig. 40. } 3) Fix the starting position of the film counter gear as shown in Fig. 41. 14. SD base plate says (see Fig. 42) 1) Make sure the contacts of the SD BASE PLATE SAYS (No. 2) and mount it on the body. NOTE: When mounting the SD BASE PLATE SAYS on the body; it may tats to the film counter and pay attention not to bend the contacts.
Arranging of all lead wires * 1) Arrange each lead wires as shown in Fig. 43 with care. 16. ASA dial (sec Fig. 44) 1) Mount the FINDER COVER No. 25 on page 36) on the —C3 body. *2) The ASA DIAL SAYS (in Fig. 44 is described upside-down. 3) Insert A and B portions of the ASA dial says into A and B portions A of the finder cover shown in Fig. Fix it with G TYPE RING O. 8) Fig. 44 Fig.
17, Care for replacement of following contacts 1) When replacing following parts, carefully cut the contacts as shown in Fig. and assemble them. (A) F stop ring says (Fig. 45). (B) Shutter dial base plate says (Fig. 46), (C) ASA contact says (Fig. 47). (D) BLC contact says (Fig. 48). 2) Shutter (see Fig. 49) A section in Fig. 49 should not be touched with fingers and hung with anything, because Mg coil is exposed. 3) Mirror box (see Fig.
=. 5. ADJUSTMENT 1. Film wind up (see Fig. 51) When changing the wind ratchet or related parts, check and make necessary adjustments. How to adjust: . . Fully wind the film wind up lever, and adjust with a SCREW so that there is a clearance of 0.05 ~ 0.1 mm after the NAIL LEVER slips off from the WIND RATCHET (in fully wound condition). NOTE: .
3. 45° mirror (see Fig. 53, 54) ‘When changing the mirror box, check and make necessary adjustments. 1) For a 45° mirror adjustment, use a millimeter and set the camera as shown in Fig. 53. 2) Adjust the chart in the center of the millimeter frame. 3) Adjust the 45° angle of the mirror with SCREWS (A) shown in Fig. 54. NOTE: 1) Absolutely refrain from turning the SCREWS (A) of Fig. 54, unless the mirror or the mirror box has been exchanged.
PRT PCT FTE, Focusing of finder {sec Fig. 5%) ‘When finder, is out of focus. T. Remove the BOTTOM COVER and adjust with SCREW shown by an arrow in Fig. 55. How to adjust: .1) When finder focus is too long, turn clockwise (Tightening dire J on). oJ or 2) When finder focus is too short, turn counter-clockwise (Loosening direction). : . Nl Sequence of checking when finder is out of focus: * 1) Check whether the lens unit correctly focus or not.
5. F stop (sce Fig. 56) Adjust F stop indication, when the F stop indication window inside the finder is out of place (outside the prescribed limit). How to adjust: D 2) 3 Install the lens (Any standard lens will do). Set the F stop of the fens to Look through the finder and turn F stop indication adjusting SCREWS in Fig. 56 so that the F stop (5.6) appearing in the F stop indication window of Fig. 56 comes to the center. a) When the figure displays at upper side of the window, loosen two SCREWS (A and B).
Body back (see Fig. @, ©) * For maintaining the interchangeability of focus, it is necessary to control the length from the mounting plate to the film surface and the parallel position between them. Length from the lens fixing mount surface to the pressure plate surface (body back) is 45.65 mm 10.02. * WW 45.65 £ 002mm Fig.
8. Electric equipment (A) AUTO EXPOSURE CHECKING LIST (Fig. 61) After the SPD circuit board has been replaced proceed as follows. LCD, VR2, VR3 and VR4 are adjusted before service parts are shipped ASA 100, S: SPEED (AUTO), F14 from Factory, so it requires no adjustment after the replacement of SPD E. STOP circuit board and never touch them. 2 Fl4 F5.6 Fl6 Lve 11.0EV Z10EV +1.0EV 1. Confirming of LCD 1) Any ASA setting, F stop and LV will do. K-13 Lvi +1.
6. WIRING DIAGRAM ‘Wind end SW Grey Shutter Yellow Ana) Green Purple i Blue = isl Brown © hme Purple Rew] Black Yellow green i White Winder contact I F sip resistor plate Battery box Release Mg Fig.
8, SKETCH INDEX AND PARTS LIST A. Top and front parts Parts represented by the encircled consecutive numbers are also deliverable as assembly parts. N\
O: using Stoic Part No. Description XR6 31261103 | Cover: wind lever © 2 31261105 | Screw 0 3 31261104 | Wind lever < . 4 31261233 | Nat: finder cover © 5 09842045W | Tapping screw: M2.0 31272150 | ME plate 7 02416030Z | Screw M1.6 31273020 | ME button holder ass’y 9 31272149 ME lock button . 10 31273002 | Shutter speed plate ass'y u 31261311 | Screw oO | 12 31261258 | Shutter dial ’ o 13 31261264 | Screw oO 14 02416050 | Screw M16 31214252 | Spring: accessory shoe 020160302 | Screw M1.6x 3.
using T SK | pant No. Description xn fin XR KE i 09841650W [Tapping screw M1.6 31261305 | Prism cover o : 3 02414040W | Screw M14 31273011 | Prism says s 31272102 | Finder frame . 6 |02416040W [Screw M1.6 31261301 [Prism frame [31261313 [LCD shield 0 i 31261014 Counter plate says 5 31272106 [LED prism E 10 [31272104 Fresnel lens ! 11 31261303 | Holder: Fresnel lens ol"! 12 |09841425W | Tapping screw M1.4 x 2.5 clock lo 13 31261312 | Shield: prism frame © 14 31261315. | Condensed light lens .O .
C. Back cover and film transport parts Parts represented by the encircled consecutive Numbers are also deliverable as assembly parts.
XR 1s, . Part No. Description X-6 Hen [tho > Sketch Part No. Description X86 [XR i ay fed 02420065Z Screw M2.0 x 6.5 ojo |Oo|O a 3126149) Back cover shield A ° 31151016 Strap metal ass’y olo|o|o (37~40) | 31261019 Back cover ass’y 0 024160252 Screw M1.6 31261020 Pressure plate ass’y ° 31261461 Clip cover o 42 31261487 Body shield A 5 31261460 Back cover latch o 43 31261310 Eyepiece frame o 31261462 Spring: back cover latch Q 4“ 31261311 Screw 31261140 Spring o 02316040W Screw M16 x 4.
D. Shutter and bottom parts Parts represented by the encircled consecutive-numbers are also deliverable as assembly parts.
. O: using X-1s, Sketch Part No. Description Xs (KR-2 re pig 1 31261021 | Battery case says © 2 02416025Z | Screw M16 31261013 | Winder contact ass’y oO 4 31261494 | Body shield ol* 5 31272128 | Front leather (right, . 6 05020080W | Screw M2.0 31261186 | Winder set position 0 8 31261113 | Holder: rewinding spring Q 9 31261112 | Rewinding spring o 10 31261151 | Holder: wind shaft o il 31261190 | Screw oO . 12 31261011 | Wind ratchet ass’y .
E. Mirror box parts Mirror box ass’y 31273024. Part bummers from are also deliverable as assembly part number 31273024.
using Sketch 500 | XR 1 Sketch i. XR 1x 500! XR.) No. Part No. Description xno Part No. Description wre R210) (1) [31261550 | Mg base plate o (36) 31261561 | Adjusting screw GC [#3] 31161608 | Spring Qo C10 0 Gn 02520030Z | Screw M2.0% 3.0 cj0]1010 3) 31161609 | Screw oO ClO 0 (38) 31261563 {Shield < @ 024160202 |Screw M1.6 x 2.
9. PARTS INDEX panorama. | Desertion around ROX | Sch X-1s) SEER $m Part No. Description 2 PRs jh Sketch 31261003, Spool friction ass’y 31261004 | Wind shaft base plate A says | © ! C19 31272102 | Finder frame BS 31261007 | Wind shaft Bass'y o i C33 31272104 | Fresnel lens B10 31261008 | Gear A says o Col den 31272166 | LED prism BY 31261009 | Gear 2.
X-f5, Part No. Description 2s) Pe jos ) Sketch . KR-10| 31261123 | Spring: wind clutch lever © C32 31261128 Shaft: gear 2.3 © Cc-15 31261132 Sprocket shaft Qo C-30 31261133 Sprocket gear © C25 31261134 Screw: sprocket © C-28. 31261140 Spring © C7 31261151 Alder: wind shaft o D-10 31261153 Nail lever Oo D-19 31261156 Spring hook oO «| D-24 31261157 Safety lever 0 D-21 31261158 Shaft: safety lever © .
X-1s, Part No. Description xns xe ad Torso jo Sketch Part No. Description Sketch 31261548 | Spring: release lever ° E48) +02016030Y [Screw M16 x30 : D41 31261549 | Mg release o E65) + 020160402 {Screw M1.6 31261550 | Mg base plate ° E<1) » 02414020Z {Screw M14 x20 C23 11261551 | Screw o ES + 02414040W | Screw M14 x 4.0 B-3 31261552 | Shield (right) o EA) * 02416016W | Screw M1.6 31261553 Shield (eft) o E<40] b E434) 31261554 | Shield (bottom) o E41) + 02416020Z | Screw M16 x 2.
