Manual

ManualsBrandsRidetech ManualsCar41183000

41173000

70-81 Camaro TigerCage

Shoulder Harness Bar Installation

Thank you for purchasing AirRide Technologies quality products. It is our privilege and goal

to provide you with quality parts that will enhance your car’s performance for many years to

come. For more information on other parts and accessories visit our web site at www.ridetech.com

Air Ride Technologies

Summary of content (9 pages)

PAGE 1
Air Ride Technologies 41173000 70-81 Camaro TigerCage Shoulder Harness Bar Installation Thank you for purchasing AirRide Technologies quality products. It is our privilege and goal to provide you with quality parts that will enhance your car’s performance for many years to come. For more information on other parts and accessories visit our web site at www.ridetech.
PAGE 2
70-81 Camaro TigerCage Shoulder Harness Bar Installation 350 S. St Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 Air Ride Technologies 41173000 IMPORTANT: Please read the entire installation procedures before starting any work. We suggest professional help with installation. AirRide Technologies does not take responsibility for any damage done to your car or AirRide Technologies products that are not properly installed.
PAGE 3
49990004 49990001 49990003 4990005 2 Main Hoop Brackets Road Race Door Bar Brackets 4990005 Shoulder Harness Bar Brackets 41173000 Package Tray Reinforcement Plates The brackets needed for the Shoulder Harness Bar installation are shown in this figure along with their part numbers. Those parts in grey are not needed for the shoulder harness Bar installation. Shoulder Harness Bar Assembly Brackets 49990000 Air Ride Technologies 70-81 Camaro TigerCage Shoulder Harness Bar Installation Fig.
PAGE 4
Clamp Assy 49990001 49990003 49990005 3 Shoulder Harness Bar Assembly 41173001 Clamp Assy 49990000 49990004 49990005 70-81 Camaro TigerCage Shoulder Harness Bar Installation 41173000 Air Ride Technologies Fig.
PAGE 5
Air Ride Technologies 41173000 70-81 Camaro TigerCage Shoulder Harness Bar Installation Step 1. Position the driver and passenger front seats towards the front of the vehicle and fold the seat backs forward to gain access to the rear seat. IMPORTANT: Before performing step 2 be aware there are two different direction clamps that make up a tiger clamp assembly. Care must be taken as to which clamp halves are bolted together.
PAGE 6
70-81 Camaro TigerCage Shoulder Harness Bar Installation Step 4. Align the hole in the tiger tab with those in the shoulder harness bar and secure using a ½” x 1 ½” 12 point bolt and ½” ﬂange nut (See Fig 6). Do both the driver and passenger sides. After the shoulder harness bar is positioned correctly ﬁnish tightening all fasteners. Always tighten the tiger tab side of the clamp ﬁrst. Remember to use Anti- Seize on all fasteners that are threaded into stainless clamps.
PAGE 7
Air Ride Technologies 70-81 Camaro TigerCage Shoulder Harness Bar Installation 41173000 IMPORTANT: When performing step 7 make sure the eyebolt jamb nuts are mounted flush against the floor pan without any carpet interfearance. l n ul o P cti e ir D Step 7. Install an eyebolt and jamb nut, supplied with harness kit Part # 49999999, in both the existing inboard and outboard seat belt mounting holes. The jamb nut must be bottomed out against the head of the eyebolt when installing.
PAGE 8
70-81 Camaro TigerCage Shoulder Harness Bar Installation Air Ride Technologies 41173000 Shoulder Belt Attachment Point IMPORTANT: After the safety harnesses have been properly installed check to make sure the proper restraint angles are correct. Depending on the type of front seat being used it may be necessary to adjust the shoulder harness bar to achieve the proper restraint angle required for the Shoulder Belts.