User guide

ManualsBrandsRidetech ManualsCar41230000

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

TGR14500 64-67 GM “A” Body TigerCage

Basic Cage

1 T108-1 Main Hoop

1 T125D-1 Driver side hoop mount

1 T125P-1 Passenger side hoop floor mount

2 T121 Hoop mount “B” pillar reinforcement plate

1 T128D Driver side hoop to frame mount (inner)

1 T128P Passenger side hoop to frame mount (inner)

1 T124D-1 Driver side hoop to frame mount (outer)

1 T124P-1 Passenger side hoop to frame mount (outer)

1 T109-1 Driver side package tray bar

1 T110-1 Passenger side package tray bar

2 T116 Package tray reinforcement plate

1 T111-1 Driver side trunk bar

1 T112-1 Passenger side trunk bar

2 T127 Trunk bar to frame mount

2 T002 Clamp tabs

1 T037P TigerClamp P (threaded)

1 T038P TigerClamp P

1 T037D TigerClamp D (threaded)

1 T038D TigerClamp D

1 Tube of Anti-Seize

1 ENG34111 Polyurethane body mount kit

Hardware:

16 3/8” x 1” USS Gr. 8 SHCS Clamps / Main hoop to mount

44 3/8” x 1 ¼” USS Gr. 8 bolt Mounting brackets

4 3/8” x 1” self-tapping screws Mounting brackets

40 3/8” USS Gr.8 Nylok nut Mounting brackets

4 3/8” Lock washer Mounting brackets

88 3/8” SAE flat washer Mounting brackets

2 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab

2 ½” Flange nut Bar to clamp tab

T125 T128 T092 T116 T121 T127

Summary of content (7 pages)

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com TGR14500 64-67 GM “A” Body TigerCage Basic Cage 1 1 1 2 1 1 1 1 1 1 2 1 1 2 2 1 1 1 1 1 1 T108-1 T125D-1 T125P-1 T121 T128D T128P T124D-1 T124P-1 T109-1 T110-1 T116 T111-1 T112-1 T127 T002 T037P T038P T037D T038D Tube of Anti-Seize ENG34111 Hardware: 16 44 4 40 4 88 2 2 3/8” x 1” USS Gr. 8 SHCS 3/8” x 1 ¼” USS Gr. 8 bolt 3/8” x 1” self-tapping screws 3/8” USS Gr.
PAGE 2
TGR14500 Installation Instructions • • • • • • • Initial fitment of the floor mount brackets must be done under the carpet. Final installation can be done under or over the carpet. Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets. Install all bars before final tightening. Always tighten the tab side of the clamp first. Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
PAGE 3
4. Bolt the inner frame brackets to the bottom of the floor pan using 3/8” Nylok nuts and flat washers. 5. The bracket will be fastened to the frame with two 3/8” x 1” selftapping screws. (The frame is boxed in this section.) The holes must first be drilled using a 5/16” bit. 7. The outer two holes of the hoop mount will attach to the outside of the frame rail with this bracket. Using the bracket as a template; drill two 3/8” holes into the frame.
PAGE 4
11. Using the template on page 7; drill four 3/8” holes into the top of the package tray. 12. Attach a “D” Clamp to the main hoop with the tab facing rearward with the top of the clamp approximately 35 9/16” above the floor mount . Use 3/8” x 1” socket head cap screws on the clamp. 13. Place the driver side package tray bar on the package tray and secure it to the clamp with a ½” x 1 ½” 12 point bolt and flange nut. 9.
PAGE 5
15. Fasten the trunk bar to the package tray bar with four 3/8” Nylok nuts and flat washers. 16. Using the trunk bar as a template drill two 3/8” holes through the vertical surface of the package tray. 17. Place the reinforcement plate on the inside of the package tray and secure with assembly with two 3/8” x 1 ¼” bolts, flat washers and Nylok nuts. Nuts should face the trunk. 18. Using the trunk bar as a template; mark the 4 holes in the floor pan with a center punch.
PAGE 6
20. Secure the frame bracket to the floor pan with four 3/8” Nylok nuts and flat washers. 21. Using the bracket as a template; drill four 3/8” holes through the frame rail. Fasten the bracket to the frame with four 3/8” x 1 ¼” bolt, Nylok nuts and flat washers. 22. You may now tighten all clamps and bolts.
PAGE 7
DRIVER SIDE THIS SIDE UP PASSENGER SIDE FLIP OVER