Manual

ManualsBrandsRidetech ManualsCar41242000

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

TGR14002 68-72 GM “A” Body TigerCage Roadrace Door Bars

DoorBars

1 T134-1 Driver side door bar

1 T135-1 Passenger side door bar

1 T098 Driver side door bar floor mount

1 T099 Passenger side door bar floor mount

2 T102 Kick panel reinforcement plate

1 T100D Driver side inner frame mount

1 T100P Passenger side inner frame mount

2 T104-1 Outer reinforcement plate

4 T002 Clamp tabs

2 T037P TigerClamp P (threaded)

2 T038P TigerClamp P

2 T037D TigerClamp D (threaded)

2 T038D TigerClamp D

1 Tube of Anti-Seize

Hardware:

16 3/8” x 1” USS Gr. 8 SHCS Clamps / Main hoop to mount

18 3/8” x 1 ¼” USS Gr. 8 bolt Mounting brackets

4 3/8” x 1 ¾” USS Gr. 8 bolt Mounting brackets

2 3/8” x 1” self-tapping screw Mounting brackets

20 3/8” USS Gr.8 Nylok nut Mounting brackets

38 3/8” SAE flat washer Mounting brackets

4 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab

4 ½” Flange nut Bar to clamp tab

2 3/8” x 1 ½” Gr. 8 bolt Seat belt tabs

2 3/8” USS Nylok nut Seat belt tabs

T099 T100 T102 T104-1

Summary of content (4 pages)

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com TGR14002 68-72 GM “A” Body TigerCage Roadrace Door Bars DoorBars 1 1 1 1 2 1 1 2 4 2 2 2 2 1 T134-1 T135-1 T098 T099 T102 T100D T100P T104-1 T002 T037P T038P T037D T038D Tube of Anti-Seize Hardware: 16 18 4 2 20 38 4 4 2 2 3/8” x 1” USS Gr. 8 SHCS 3/8” x 1 ¼” USS Gr. 8 bolt 3/8” x 1 ¾” USS Gr. 8 bolt 3/8” x 1” self-tapping screw 3/8” USS Gr.8 Nylok nut 3/8” SAE flat washer ½” x 1 ½” 12 point Gr.
PAGE 2
TGR14002 Installation Instructions • • • • • • • Initial fitment of the floor mount brackets must be done under the carpet. Final installation can be done under or over the carpet. Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets. Install all bars before final tightening. Always tighten the tab side of the clamp first. Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
PAGE 3
5. To install the front floor pan bracket, the kick panel must be removed. 6. Use the door bar to determine the location of the floor pan mount. Drill two 3/8” holes in the kick panel. Place the reinforcement plate inside the kick panel and secure the assembly with two 3/8” x 1 ¼” bolts, flat washers and lock washers. 7. Remove the door bars. 8. Using the bracket as a template, drill four 3/8” holes through the floor pan. (The middle two do not need to be drilled). 9.
PAGE 4
12. Since the door bar covers the factory lap belt mounting holes, tabs are welded to the bar to secure the lap belts. 3/8” x 1 ½” bolts are supplied. 13. All clamps and bolts may now be tightened.