User guide

ManualsBrandsRidetech ManualsCar41260000

TGR11000 68-74 Nova TigerCage

Basic Cage

1 T083-1 Main hoop assembly

1 T021D-1 Driver side hoop mount

1 T021P-1 Passenger side hoop mount

2 T012 Main hoop reinforcement plate (inside quarter)

2 T013 Main hoop reinforcement plate (under car)

1 T087-1 Driver side package tray bar

1 T088-1 Passenger side package tray bar

2 T016 Package tray reinforcement plate

1 T090-1 Passenger side trunk bar

1 T089-1 Driver side trunk bar

2 T014 Trunk bar reinforcement plate (under car- outer)

2 T015 Trunk bar reinforcement plate (under car- inner)

2 T002 Clamp tab

1 T037P TigerClamp P (threaded)

1 T038P TigerClamp P

1 T037D TigerClamp D (threaded)

1 T038D TigerClamp D

1 Tube of Anti-Seize

Hardware:

16 3/8” x 1” USS Gr. 8 SHCS Clamps / Main hoop to mount

4 3/8” x 1” USS Gr.8 bolt Main hoop mount reinforcement plate to pinch weld

8 3/8” Lock washer Main hoop mount to inside reinforcement plate

32 3/8” x 1 ¼” USS Gr. 8bolt Main hoop mount to reinforcement plates/ trunk bars

36 3/8” USS Gr.8 Nylok nut Main hoop mount reinforcement plates

72 3/8” SAE flat washer Main hoop mount / trunk bars

2 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab

2 ½” Flange nut Bar to clamp tab

T021-1 Main Hoop Mount T016 Package Tray Plate T014 Trunk Bar Plate-Outer T015 Trunk Bar Plate- Inner

T013 Hoop Plate- Under T012 Hoop Mount Plate- Inside T002 TigerClamp Tab

Summary of content (7 pages)

PAGE 1
TGR11000 68-74 Nova TigerCage Basic Cage 1 1 1 2 2 1 1 2 1 1 2 2 2 1 1 1 1 1 Hardware: 16 4 8 32 36 72 2 2 T083-1 T021D-1 T021P-1 T012 T013 T087-1 T088-1 T016 T090-1 T089-1 T014 T015 T002 T037P T038P T037D T038D Tube of Anti-Seize Main hoop assembly Driver side hoop mount Passenger side hoop mount Main hoop reinforcement plate (inside quarter) Main hoop reinforcement plate (under car) Driver side package tray bar Passenger side package tray bar Package tray reinforcement plate Passenger side trunk bar Dri
PAGE 2
TGR11000 Installation Instructions • • • • • • • Initial fitment of the floor mount brackets must be done under the carpet. Final installation can be done under or over the carpet. Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets. Install all bars before final tightening. Always tighten the tab side of the clamp first. Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
PAGE 3
. Using the bracket as a template drill four 3/8” holes in the floor pan. Fasten the upper holes in the bracket to the quarter panel structure with two 3/8” x 1 ¼ bolts, flat washers and Nylok nuts. A reinforcement plate will be installed inside the quarter panel. 4. Secure the lower portion of the bracket to the floor pan with two 3/8” x 1 ¼” bolts, flat washers and Nylok nuts. Another reinforcement plate will be installed under the car. It will also meet up with the body seam. 5.
PAGE 4
9. The next bar to be installed is the package tray bar. 10. Before installing the bar, use the template on page 7 to drill four holes in the top of the package tray for the bar flange to bolt to. 11. Fasten the clamp to the main hoop with the tab facing rearward. Use clamp D on the driver side and clamp P on the passenger side. 12. The other end of the bar will attach to the top of the package tray. Drop four 3/8” x 1 ¼” bolts with flat washers down through the package tray. 13.
PAGE 5
14. Bolt the trunk bar up to the package tray bar with 3/8” Nylok nuts and flat washers. 15. Using the bracket as a template drill two 3/8” holes through the vertical surface of the package tray. 16. Place the reinforcement plate inside the car and fasten with two 3/8” x 1 ¼” bolts and Nylok nuts. 17. Using the trunk bar plate as a template, drill six 3/8 holes through the trunk floor. Drop six 3/8” x 1 ¼” bolts with flat washers down through the holes. 18.
PAGE 6
TigerClamp Location Chart
PAGE 7
Package Tray Bar Template