Instructions / Assembly

4501 08-005 11/16
© 2016, Ridge Tool Company.
SPECIFICATIONS • ESPECIFICACIONES
POWER SUPPLY REQUIREMENTS
REQUISITOS DE SUMINISTRO DE ENERGÍA
120 V, 60 Hz
120 V, 60 Hz
MOTOR,
MOTOR
Single Phase, Dielectric Oil Filled
Monofásico, lleno de aceite dieléctrico
HORSEPOWER
CLASIFICACIONES DE CABALLOS DE
FUERZA
1 HP .................... (1000RS)
1/2 HP ................. (500RS)
1/3 HP ................. (330RS)
LIQUID TEMPERATURE RANGE
RANGO DE TEMP. DEL LÍQUIDO
40° F to 120° F
4 ºC a 48 ºC (40 °F a 120 °F)
CIRCUIT REQUIREMENTS
REQUISITOS DEL CIRCUITO
15 A (minimum)
15 A (minimum)
DIMENSIONS
DIMENSIONES
11-1/2 in. high x 9-3/4 in. base
29,2 cm (11-1/2 pulg.) de alto x 24,7 cm (9-3/4) pulg. de base
ON LEVEL (FACTORY SET)
NIVEL DE ACTIVACIÓN (CONFIGURACIÓN DE FÁBRICA)
Approximately 9 in.
Aproximadamente 23 cm
(9 pulg.)
OFF LEVEL (FACTORY SET)
NIVEL DE CORTE (CONFIGURACIÓN DE FÁBRICA)
Approximately 4 in.
Aproximadamente 10
cm (4 pulg.)
CONSTRUCTION • CONSTRUCCIÓN
MOTOR HOUSING
CUBIERTA DEL MOTOR
500RS, 330RS Cast Iron, Hierro fundido
1000RS Stainless Steel,
VOLUTE
ESPIRAL
IMPELLER
IMPULSOR
Glass Reinforced Thermoplastic
Termoplástico reforzado con vidrio
SHAFT, EJE Steel, Carbono
DISCHARGE, DESCARGA 1-1/2 in. NPT, 3,8 cm (1-1/2 pulg.) NPT
Submersible Sump Pump
Bomba sumergible para sumidero
Please read and save these instructions. This manual contains important Safety Warnings and Operating Instructions. You will need to refer to it before attempting
any installation or maintenance. Always keep this manual with the unit so that it will be easily accessible. Failure to read and follow these warnings and
instructions could result in property damage, serious injury or death.
Sírvase leer y guardar estas instrucciones. Este manual contiene Advertencias de seguridad e Instrucciones de funcionamiento. Deberá consultar
el mismo antes de realizar cualquier instalación o mantenimiento. Siempre mantenga este manual con la unidad de forma de acceder al mismo
fácilmente. No leer ni respetar estas advertencias e instrucciones podría dar como resultado daño a la propiedad, lesiones graves o la muerte.
WARRANTY & SERVICE PARTS SHEET
HOJA DE GARANTÍA Y PIEZAS DE REPUESTO
1. GFCI GROUNDED OUTLET
2. POWER CORD PLUG
3. BASIN
4. DISCHARGE PIPE
5. PUMP
6. INLET
7. VENT PIPE
8. CHECK VALVE
9. GASKET/BASIN LID
1. TOMACORRIENTE GFCI CONECTADO
A TIERRA
2. ENCHUFE DEL CABLE DE
CORRIENTE RETENCIÓN
3. PILETA
4. TUBERÍA DE DESCARGA
5. BOMBA
6. ENTRADA
7. TUBERÍA DE VENTILACIÓN
8. VÁLVULA DE
9. JUNTA/TAPA DE LA PILETA
ON LEVEL
(APPROX. 9 IN.)
NIVEL DE ACTIVACIÓN
(APROXIMADAMENTE 23 CM)
OFF LEVEL (APPROX. 4 IN.)
NIVEL DE CORTE
(APROXIMADAMENTE
10 CM)
1
2
3
4
6
8
5
7
9
11 IN. DIAMETER MIN.
DIÁMETRO MÍNIMO DE LA PILETA 27, 94 cm (11 pulg.)
PERFORMANCE • RENDIMIENTO
Model
Modelo
HP
HP
Discharge Head
Cabeza de descarga
0 ft
0 m
5 ft
1,5 m
10 ft
3 m
15 ft
4,5 m
1000RS 1
Gal / hr 5400 4860 3960 2940
L / hr 20.441 18.397 14.99 11.129
500RS 1/2
Gal / hr 4920 4380 3660 2880
L / hr 18.624 16.580 13.855 10.902
330RS 1/3
Gal / hr 4320 3600 2880 2160
L / hr 16.353 13.627 10.902 8.17
Cast Iron, Hierro fundido