User Guide

ManualsBrandsRIDGID ManualsPlumbing Product300 Power Drive Complete NPT

1206 Stand Instructions

WARNING

Read these instructions and the warnings and instruc-

tions for all equipment being used before using

RIDGID

stands to reduce the risk of serious person-

al injury.

• Always wear eye protection to reduce the risk of eye

injury.

• Support pipe with pipe stands. Failure to properly sup-

port the pipe can cause stand tipping, falling pipe and seri-

ous injury.

If you have any question concerning this RIDGID

product:

– Contact your local RIDGID distributor.

– Visit www.RIDGID.com or www.RIDGID.eu to find your

local RIDGID contact point.

– Contact RIDGID Technical Services Department at rtctech-

services@emerson.com, or in the U.S. and Canada call

(800) 519-3456.

Description

The RIDGID

1206 Stand is used to mount and support the

300 Power Drive and other RIDGID products. It is equipped

with tool hangers and a tray for equipment storage during use.

The 1206 Stand easily folds for storage and transportation and

allows adjustment of stand stiffness.

Assembly

Figure 1 – Assembling 1206 Stand

1. Place the base on a flat surface with the leg pockets fac-

ing up.

2. The rear leg includes a leg chain and tray support. Install

the rear leg with the foot pointing out in the leg pocket

opposite the carry handle. Secure with bolt and nut.

3. With feet pointing out, install the interchangeable front

legs into the leg pockets closest to the carry handle.

Secure with bolts and nuts.

1206 Stand Instruction Sheet

4. Position the tray so that rolled edges are facing down.

Align the holes in the tray tabs with the holes in the

legs/tray support and fully insert the tray pins.

5. Place the X washers on the grooves in the tray pins and

use pliers to close the long ends together.

Inspection/Maintenance

The 1206 Stand should be inspected before each use for wear

or damage that could affect safe use. Clean the stand to aid

inspection and help prevent handles, etc. from slipping from

your grip. If any problems are found, do not use until the

problems are corrected.

1206 Stand Set-Up and Operation

1. Locate a clean, level, stable location to set up stand.

2. Place stand with feet on floor and open legs. Carefully

push down on the center of the tray and lock into position.

Keep fingers and hands away from pinch points to prevent

injury.

3. A properly adjusted stand in good condition should sit

solidly with no significant looseness. To adjust:

a. Remove all objects (pipe, tools, etc.) from stand.

Carefully push up on the tray to unlock. Stay clear of

moving legs.

Figure 2 – Adjusting Tray Support

b. Loosen the set screw on the rear tray support.

c. Move the rear tray support towards the base to in -

crease stiffness, and away from the base to decrease

stiffness.

d. Firmly tighten the set screw on the rear tray support.

Repeat above steps 1-3 until properly adjusted. On worn

out stands, adjustment may not be possible.

4. Anchoring for greater stability – Holes are provided in the

leg feet to fasten the stand to the floor. Always anchor the

stand when using with geared threaders to prevent tip-

ping.

5. Place the 300 Power Drive on the stand and secure

with the supplied fasteners. Attach other equipment as

directed in the equipment instructions.

6. Make sure the stand, equipment and pipe are stable for

the work to be done. Use appropriate pipe supports.

Failure to properly support the pipe can cause equipment

tipping, falling pipe and serious injury.

RIDGID

6/11

999-998-461.10

REV. C

Printed in U.S.A.

EC38213

Rear Leg

Leg Chain

Tray

Foot Out

Carry Handle

Base

Tray Support

Increase

Stand Stiffness

Decrease

Set

Screw

Base

Front Legs

Summary of content (4 pages)

PAGE 1
206 Stand Instruction Sheet 4. Position the tray so that rolled edges are facing down. Align the holes in the tray tabs with the holes in the legs/tray support and fully insert the tray pins. 5. Place the X washers on the grooves in the tray pins and use pliers to close the long ends together.
PAGE 2
Trépied 1206 : Mode d’emploi Trépied 1206 : Mode d’emploi AVERTISSEMENT Afin de limiter les risques d’accident grave, familiarisez-vous avec les consignes ci-présentes, ainsi qu’avec les avertissements et consignes visant l’ensemble du matériel utilisé avant de vous servir d’un trépied RIDGID®. • Portez systématiquement une protection oculaire afin de limiter les risques de blessure oculaire. • Soutenez le tuyau à l’aide de porte-tubes.
PAGE 3
Modo de empleo: Trípode N° 1206 4. Ancrage des pieds pour une stabilité absolue – Les pieds des jambages sont pourvus de trous d’ancrage qui permettent de les arrimer au sol. Afin de parer aux risques de renversement, ancrez le trépied systématiquement lors de l’utilisation d’une fileteuse démultipliée. 5. Montez le système d’entraînement 300 Power Drive sur le trépied à l’aide de la quincaillerie fournie, et tout autre matériel utilisé selon les instructions correspondantes. 6.
PAGE 4
Modo de empleo: Trípode N° 1206 Basa Aumentar Rigidez de las patas Disminuir Tornillo de retención Figura 2 – Ajuste del soporte de la repisa d. En el soporte de la repisa en la pata trasera, apriete el tornillo de retención firmemente. Repita los pasos 1 al 3 hasta lograr la tensión deseada de las patas. Es posible que este ajuste no pueda efectuarse en un trípode deteriorado. 4. Anclaje del trípode para mayor estabilidad – las patas del trípode cuentan con agujeros para atornillarlas al suelo.