Use and Care Manual

ManualsBrandsRIDGID ManualsKitchenTile Saw Stand

English

WARNING:

To reduce the risk of injury, do not attempt to use

this product until you have read thoroughly and

understand completely this Operator's Manual and

the Operator’s Manual for your tile saw.

UNPACKING

This product has been shipped completely assembled.

n Carefully remove the product from the box. Make sure

that all items listed in the packing list are included.

WARNING:

Do not use this product if it is not completely

assembled or if any parts appear to be missing

or damaged. Use of a product that is not properly

and completely assembled could result in serious

personal injury.

n Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

n Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

n If any parts are damaged or missing, please call

1-866-539-1710 for assistance.

WARNING:

If any parts are damaged or missing do not operate

this tool until the parts are replaced. Use of this

product with damaged or missing parts could result

in serious personal injury.

PACKING LIST

See Figure 1.

Stand, Height Adjustment Pin (4), and Operator’s Manual

SETTING UP THE STAND

See Figures 2 - 5.

nWith the unit in the upright position, spread the legs of

the stand. Place stand on level ground.

NOTE: When positioning the stand make sure each leg

is spread fully outward to ensure the stand’s stability.

nTo adjust the height of the stand, move each adjustable

foot up or down until the hole in the leg is aligned with

one of the holes in the foot. Secure the feet in place using

height adjustment pins with bales.

NOTE: Make sure the feet are positioned at the same

height to ensure stability.

nLine up channels under tile saw with braces on stand.

Position saw onto stand. Make sure that the tile saw is

flush against the stand and that all the stand legs are

touching the ground.

nMake sure the stand is stable and on level ground before

using the tile saw.

CALIFORNIA PROPOSITION 65

WARNING:

This product may contain chemicals, including

lead, known to the State of California to cause

cancer, birth defects or other reproductive harm.

Wash hands after handling.

OPERATOR’S MANUAL

TILE SAW STAND

AC11305

To register your RIDGID product,

please visit: http://register.RIDGID.com

SAVE THESE INSTRUCTIONS

990000356

12-11-12 (REV:01)

ONE WORLD TECHNOLOGIES, INC.

P.O. Box 35, Hwy. 8, Pickens, SC 29671

1-866-539-1710 / www.ridgid.com

FOR USE ONLY WITH THE RIDGID R4030 AND

R4040 TILE SAW

Summary of content (8 pages)

PAGE 1
OPERATOR’S MANUAL TILE SAW STAND AC11305 FOR USE ONLY WITH THE RIDGID R4030 AND R4040 TILE SAW To register your RIDGID product, please visit: http://register.RIDGID.com SAVE THESE INSTRUCTIONS PACKING LIST WARNING: See Figure 1. To reduce the risk of injury, do not attempt to use this product until you have read thoroughly and understand completely this Operator's Manual and the Operator’s Manual for your tile saw.
PAGE 2
WARRANTY RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting warranty service. Limited to RIDGID® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID®, Inc. All warranty communications should be directed to One World Technologies, Inc.
PAGE 3
MANUEL D’UTILISATION STAND POUR SCIE À CARREAUX AC11305 POUR UTILISATION AVEC SCIE A CARREAUX RIDGID R4030 ET R4040 Pour enregistrer votre produit de RIDGID, s’il vous plaît la visite: http://register.RIDGID.com CONSERVER CES INSTRUCTIONS LISTE DE CONTRÔLE AVERTISSEMENT : Voir la figure 1. Pour réduire les risques de blessures, ne pas tenter d’utiliser ce produit avant d’avoir lu entièrement et bien compris le présent manuel d’utilisation ainsi que le manuel d’utilisation de la scie à carreaux.
PAGE 4
GARANTIE OUTILS ÉLECTRIQUES À MAIN ET D’ÉTABLI RIDGID® GARANTIE LIMITÉE DE SERVICE DE 3 ANS Une preuve d’achat doit être présentée pour toute demande de réparation sous garantie. Cette garantie se limite aux outils électriques à main et d’établi RIDGID® achetés à partir du 1/2/04. Ce produit est fabriqué par One World Technologies, Inc., sous licence de marque de RIDGID®, Inc. Toutes les communications de garantie doivent être adressées à One World Technologies, Inc.
PAGE 5
MANUAL DEL OPERADOR PEDESTAL PARA SIERRA DE LOSAS AC11305 PARA USAR CON SIERRA DE LOSAS RIDGID R4030 Y R4040 Para registrar su producto de RIDGID, por favor visita: http://register.RIDGID.com GUARDE ESTAS INSTRUCCIONES LISTA DE EMPAQUETADO ADVERTENCIA: Vea la figura 1. Para reducir el riesgo de lesiones, no intente usar este producto hasta que haya leído y comprendido totalmente este manual del operador y el manual del operador de la sierra de losas.
PAGE 6
GARANTÍA HERRAMIENTAS ELÉCTRICAS DE MANO Y ESTACIONARIAS RIDGID® — GARANTÍA DE SERVICIO LIMITADA DE TRES AÑOS Debe presentarse prueba de la compra al solicitar servicio al amparo de la garantía. Se limita a las herramientas de mano y estacionarias RIDGID® adquiridas a partir de 1/Feb./04. Este producto está manufacturado por One World Technologies, Inc., La licencia de uso de la marca comercial es otorgada por RIDGID, Inc.
PAGE 7
NOTES / NOTAS
PAGE 8
Fig. 1 Fig. 4 D A A B C A B B A B C D - Channel (glissière, canal) Brace (renfort, riostra) Stand (stand, pedestal) Tile saw (scie à carreaux, sierra de losas) Fig. 5 A - Stand (stand, pedestal) B - Height adjustment pin (axe de réglage de hauteur, pasador de ajuste de altura) Fig. 2 Fig.