OPERATOR’S MANUAL Miter Saw Utility Vehicle TM AC99402 For Use With RIDGID 10 in. and 12 in. Miter Saws and other miter saws This Miter Saw Utility Vehicle has been engineered and manufactured to our high standard for dependability, ease of operation and operator safety. When properly cared for, the Miter Saw Utility Vehicle will give you years of rugged, troublefree performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
TABLE OF CONTENTS n Introduction ...................................................................................................................................................................... 2 n Rules for Safe Operation .................................................................................................................................................. 3 n Symbols.............................................................................................................................
RULES FOR SAFE OPERATION Safe operation of this accessory requires that you read and understand this operator's manual, the operator’s manual for the miter saw and all labels affixed to the tool. n Maximum weight of power tool must not exceed 100 pounds. n Maximum weight of saw and workpiece must not exceed 200 pounds. n Always mount miter saw so the workpiece is positioned in-line with the roller assemblies. n Check to make sure workstand does not rock, slide or move prior to use.
SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
UNPACKING NOTE: Before beginning assembly, check that all parts are included. If you are missing any part, do not assemble this accessory. Call 1-800-4-RIDGID or E-mail us at info@rid gidwoodworking.com to get the missing part. Sometimes small parts can get lost in packaging material. Do not throw away any packaging until the accessory is completely assembled and your power tool is attached. Check packaging for missing parts before contacting RIDGID.
ASSEMBLY ATTACHING THE LOWER FOOT MOUNTING WHEELS n Place stand assembly “flat” on floor. n Slide axle bolt outwards until it extends beyond the frame. n Remove axle lock nut and one washer. See Figure 3. See Figures 1 d 2. n Rotate lower foot into upright position aligning holes as shown. n Locate the following parts: Hex Bolt, M8 x 50 mm (2) Flat Washer, M8 (4) Lock Nut, M8 (2) WARNING: Do not remove axle bolt(s) from the frame.
ASSEMBLY WORKSTAND SET-UP See Figures 4 - 5. WARNING: Before You Start To avoid serious personal injury when lifting, bend your knees so you can lift with your legs, not your back. n If a miter saw is already assembled to the stand, make sure that it is securely attached to the stand per the instructions in this manual. n The sliding legs will follow tracks on the underside of the table to their engaged position near the handle end of the table. n Return table to horizontal position.
ASSEMBLY MOUNTING MITER SAW n Slide flat washer on hex bolt and place through miter saw base and workstand. The larger fender type flat washer can be placed on the bottom or top of the miter saw. Certain mountings will require this washer to be placed on top of the miter saw in order to provide clearance with the frame. See Figures 6 - 7. WARNING: Failure to unplug the tool could result in accidental starting causing possible serious personal injury.
ASSEMBLY MOUNTING OTHER BRANDS MOUNTING AND ALIGNING ROLLER ASSEMBLY See Figure 8. NOTE: Other brands of miter saws (not RIDGID miter saws) will require additional 5/16 in. mounting holes to be drilled. See instructions below. n Locate the following parts: Hex Bolts, M6 x 40mm (4) Flat Washers, M6 (4) Fender Washers, M6 (4) Lock Nuts, M6 (4) See Figure 9. n Insert roller assembly into each extension bar. NOTE: Make sure length stop is positioned towards miter saw.
ASSEMBLY EXTENSION BAR(S) OPERATION NOTE: There is a catch to limit the overall extension bar travel. See Figures 10 - 11. Both extension bars may be adjusted to provide maximum workpiece support. To adjust the extension bars: n Pull out on locking pin knob and swing leg down until n Loosen adjustable handle by turning counter clock- n Turn foot knob counterclockwise to loosen and slide locking pin locks leg in the down position. foot extension down until foot contacts the floor. Tighten foot knob.
ASSEMBLY FOLDING AND MOVING WORKSTAND See Figures 12, 13, and 14. LOWER THE TABLE Fig. 13 n Lift stand into upright position pull out on the spring pin knob, and swing the legs until they lock in place against the bottom of the table. Fig. 12 n Make sure the stand will remain upright on its own. Before You Start n Remove any workpieces, clamps or other accessories.
ASSEMBLY TRANSPORTING TOOL MAINTENANCE See Figure 15. See Figures 16 - 17. n When hauling the workstand in a vehicle, securely tie it n Periodically clean the sliding roller tracks as shown down to prevent movement and possible damage. below. n Always get help if you need to lift the workstand. When n Also clean and lubricate the locking handle. lifting, hold the workstand close to your body. Bend your knees so you can lift with your legs, not your back. KEEP AREA CLEAN Fig.
37 4 2 3 3 23 15 23 41 9 17 9 8 18 43 9 8 18 17 1 19 44 2 17 9 8 39 45 10 15 29 23 42 3 24 4 2 37 34 33 36 3 5 35 38 11 7 18 8 7 2 2 15 31 22 25 26 27 12 32 29 15 2 42 17 9 23 15 18 43 8 9 14 30 23 24 23 21 13 22 25 44 33 19 27 26 21 20 20 28 16 16 15 5 2 45 3 4 13 14 11 6 19 17 1 9 8 8 17 8 9 18 24 2 3 7 1 22 24 31 28 10 34 9 23 41 33 8 15 39 19 15 32 23 Part Description No.
NOTES 14
WARRANTY RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY WHAT IS NOT COVERED Proof of purchase must be presented when requesting warranty service. This warranty applies only to the original purchaser at retail and may not be transferred.
OPERATOR’S MANUAL Miter Saw Utility Vehicle TM AC99402 For Use With RIDGID 10 in. and 12 in. Miter Saws and other miter saws Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com.