OPERATOR’S MANUAL 18 VOLT HAND PLANER WITH SPIRAL CUT R848 Your hand planer has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying a RIDGID product.
TABLE OF CONTENTS n Introduction .....................................................................................................................................................................2 n General Safety Rules ................................................................................................................................................... 3-4 n Specific Safety Rules..................................................................................................................
GENERAL SAFETY RULES n Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations. n Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. n Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents. n Do not use on a ladder or unstable support.
GENERAL SAFETY RULES SERVICE n When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. n Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury.
SAFETY RULES FOR CHARGER tain chemicals that can damage, weaken, or destroy plastic. WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. n An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
FEATURES PRODUCT SPECIFICATIONS Motor ......................................................................................................................................................................18 Volt DC Switch............................................................................................................................................................... Single Speed No Load Speed .......................................................................................................
FEATURES KNOW YOUR HAND PLANER DEPTH ADJUSTMENT KNOB See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. The depth adjustment selects 0-1/16 in. planing depths, in increments of 1/64 in. CHIP COLLECTION SWITCH TRIGGER Your hand planer has a conveniently located switch trigger on the underside of the rear handle. The dust bag attaches to the chip exhaust of the planer to keep the work area free of debris. A 1-1/4 in.
ASSEMBLY INSTALLING/REMOVING THE DUST BAG UNPACKING See Figure 2. The dust bag located on the right side of the hand planer provides a dust collection system. Wood particles are drawn up through the base and collect in the dust bag during operation. For more efficient operation, empty the dust bag when half full. This product has been shipped completely assembled. n Carefully remove the tool and any accessories from the box. n Make sure that all items listed in the packing list are included.
OPERATION WARNING: Do not allow familiarity with your tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. Fig.
OPERATION LED FUNCTION OF CHARGER See Figure 5.
OPERATION TO INSTALL BATTERY PACK See Figure 6. n Lock the switch. n Place the battery pack in the tool. Align raised rib on battery pack with the groove inside the tool. n Make sure the latches on each side of the battery pack snap in place and battery pack is secured in the tool before beginning operation. CAUTION: When placing battery pack in the tool, be sure raised rib on battery pack aligns with the bottom of the tool and latches into place properly.
OPERATION LOCK-OFF BUTTON WARNING: Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side. STARTING/STOPPING THE PLANER See Figure 8. n To start the planer: Push the lock-off button from either side, and then depress the switch trigger. n To stop the planer: Release the switch trigger. KICKSTAND See Figure 9.
OPERATION FRONT HANDLE OPERATING THE PLANER See Figure 11. n Clamp the work securely. WARNING: Work moving during a cut could result in loss of control of the planer and cause serious injury. n Support the work so that the operation is on your right. REAR HANDLE n Adjust the planing depth. n Hold the planer with both hands. Hold the front handle with your left hand and the rear handle with your right hand. WARNING: Always use two hands on the tool for any operation.
OPERATION GROOVE CHAMFERING See Figure 12. The planer is designed with a chamfering groove in the front shoe to chamfer edges of boards as shown. Before making a cut on good lumber, practice cutting on scrap lumber to determine the amount to be removed. n Clamp the work securely. n Hold the front handle with your left hand and the rear handle with your right hand. FRONT HANDLE n Place the chamfering groove on the surface to be cut. n Start the planer and let the motor reach maximum speed.
OPERATION PLANING EDGES See Figure 14. Follow the directions in the “Planing” section earlier in this manual. Hold the edge guide firmly against the edge of the work surface. ATTACHING THE EDGE GUIDE FOR MAKING RABBET CUTS n Lock the switch by placing the lock-off button in the center position. n Attach the bracket to the left side of the planer using the knob bolt. n Attach the edge guide loosely to the bracket using the knob nut and the carriage head bolt.
MAINTENANCE GENERAL MAINTENANCE WARNING: Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc.
MAINTENANCE REPLACING BLADES See Figures 17 - 18. Always replace blades in pairs. Do not attempt to sharpen blades. If the blades become dull, replace them. BLADE BLADE CLAMP BLADE WRENCH When replacing the blades, use recommended replacement blade only, RIDGID part number 671480001. SCREWS WARNING: Blades are sharp. Use extreme caution when replacing the blades. Failure to heed this warning can result in serious personal injury. n Remove the battery. n Secure the planer in an upside-down position.
MAINTENANCE REPLACING THE BELT See Figures 19 - 20. PULLEY When replacing the belt, use the recommended replacement belt only, RIDGID part number 570279001. BELT COVER n Lock the switch by placing the lock-off button in the center position. n Remove belt cover screws. n Remove the belt cover. n Remove the old drive belt from the small pulley by turning the large pulley in a counterclockwise direction.
WARRANTY RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY WHAT IS NOT COVERED Proof of purchase must be presented when requesting warranty service. This warranty applies only to the original purchaser at retail and may not be transferred.
OPERATOR’S MANUAL 18 VOLT HAND PLANER WITH SPIRAL CUT R848 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided below.
