OPERATOR’S MANUAL ANGLED FINISH NAILER R250AFA Your angled finish nailer has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying a RIDGID product.
TABLE OF CONTENTS n Introduction .....................................................................................................................................................................2 n General Safety Rules .......................................................................................................................................................3 n Specific Safety Rules.................................................................................................................
GENERAL SAFETY RULES n Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. DANGER READ AND UNDERSTAND TOOL LABELS AND MANUAL. Failure to follow warnings could result in DEATH or SERIOUS INJURY. n Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
SPECIFIC SAFETY RULES n �Always be aware that misuse and improper handling of this tool can cause injury to yourself and others. n N � ever clamp or tape the trigger or workpiece contact in an actuated position. n �Never leave a tool unattended with the air hose attached. n �Do not operate this tool if it does not contain a legible warning label. n �Do not continue to use a tool that leaks air or does not function properly. n Know your power tool. Read operator’s manual carefully.
SPECIFIC SAFETY RULES AIR SUPPLY AND CONNECTIONS LOADING TOOL n Do not load the tool with fasteners when any one of the operating controls is activated. n �Do not use oxygen, combustible gases or bottled gases as a power source for this tool as tool will explode, possibly causing injury or death. When loading tool: n Do not use with an air compressor which can potentially exceed 200 P.S.I. as tool may burst, possibly causing injury.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Read The Operator’s Manual To reduce the risk of injury, user must read and understand operator’s manual before using this product. Eye Protection Always wear safety goggles, safety glasses with side shields, or a full face shield when operating this product.
GLOSSARY OF TERMS Activate (operating controls) To move an operating control so that it is in a position that allows the tool to be actuated or that satisifes one requirement for the tool to be actuated. Air inlet port In an air tool, the opening to which the compressed air supply is connected, usually by means of a threaded fitting. Fastener A staple, pin, brad, nail, or other fastening device which is designed and manufactured for use in the tools within the scope of this standard.
FEATURES PRODUCT SPECIFICATIONS Operating Pressure.................................................................................................................................................70-120 psi Fastener Type ......................................................................................................................................... 15 gauge finish nails Fastener Range ....................................................................................................................
FEATURES IN-HANDLE AIR FILTER KNOW YOUR FINISH NAILER See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. The self-cleaning in-handle air filter helps keep debris out to extend the life of the tool. ADJUSTABLE EXHAUST A tool-free jam release is provided for ease in clearing infrequent jams. JAM RELEASE The exhaust can be adjusted to a variety of positions depending on operator preference.
ASSEMBLY UNPACKING This product has been shipped completely assembled. WARNING: n Carefully remove the tool and any accessories from the box. If any parts are missing do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. n Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
OPERATION AIR FITTING WARNING: Always wear eye protection. Eye protection does not fit all operators in the same way. Make sure the eye protection chosen has side shields or provides protection from flying debris both from the front and sides. PREPARING THE TOOL FOR USE See Figure 2. Under normal use conditions, the tool should be lubricated before connecting the tool to an air supply. Add air tool lubricant into the air fitting on the tool once daily with minimal use, or twice a day with heavy use.
OPERATION SWIVEL CONNECTOR WARNING: Disconnect the tool from the air supply before leaving the work area, moving the tool to another location, or handing the tool to another person. Failure to do so could result in serious personal injury. AIR HOSE CONNECTOR CONNECTING THE TOOL TO AN AIR SUPPLY See Figure 5. DANGER: Do not use oxygen, combustible gases or bottled gases as a power source for this tool. The tool will explode and cause death or serious injury. Fig.
OPERATION LOADING THE TOOL WITH NAILS See Figures 6 - 7. n Connect the tool to the air supply. MAGAZINE WARNING: The tool’s driving mechanism may cycle when the tool is first connected to the air supply. Always connect the tool to the air supply before loading nails to prevent injury from unintended cycling. Always make sure the tool’s magazine is empty at the beginning of each work session, before connecting to an air supply.
OPERATION USING THE SELECTABLE TRIGGER TRIGGER LEVER PIVOT PIN (DEPRESS TO ALLOW SELECTOR TO ROTATE) See Figures 8 - 9. WARNING: Never wedge or hold back the workpiece contact mechanism during operation of the tool. Doing so could result in possible serious injury. This tool is shipped from the factory with a selectable trigger set in the Single Sequential Actuation mode. The selectable trigger can also be set for Contact Actuation mode.
OPERATION SETTING THE AIR PRESSURE The amount of air pressure required will depend on the size of the nail and the workpiece material. Begin testing the depth of drive by driving a test nail into the same type of workpiece material used for the actual job. Drive a test nail with the air pressure set at 90-95 psi. Raise or lower the air pressure to find the lowest setting that will perform the job with consistent results.
OPERATION CLEARING A JAMMED FASTENER See Figure 12. WARNING: Disconnect the tool from the air supply before clearing a jammed fastener. Failure to do so could result in serious personal injury. If a nail or fastener becomes jammed in the tool, disconnect the air hose and keep the tool pointed away from you while clearing the jam. n Open magazine and remove fasteners from the tool. n �Pull up on the latch and open the jam release.
MAINTENANCE LUBRICATION WARNING: �Frequent, but not excessive, lubrication is required for best performance. Oil for pneumatic fastening tools added through the air line connection will lubricate the internal parts. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance. When servicing use only identical RIDGID replacement parts.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Air leak near the top of the tool or in the trigger area Loose screws Tighten screws Worn or damaged O-rings or seals Install Overhaul Kit Air leak near the bottom of the tool Loose screws Tighten screws Worn or damaged O-rings or bumper Install Overhaul Kit Tool does nothing or operates sluggishly Inadequate air supply Verify adequate air supply Inadequate lubrication Lubricate tool Worn or damaged O-rings or bumper Install Overhaul Kit In
WARRANTY RIDGID® PNEUMATIC TOOL 3 YEAR LIMITED SERVICE WARRANTY WHAT IS NOT COVERED Proof of purchase must be presented when requesting warranty service. This warranty applies only to the original purchaser at retail and may not be transferred.
OPERATOR’S MANUAL ANGLED FINISH NAILER R250AFA Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the magazine. Please record the serial number in the space provided below.