OPERATOR’S MANUAL 9.6 VOLT PIVOTING SCREWDRIVER VARIABLE SPEED/REVERSIBLE R81030 Your screwdriver has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying a RIDGID product.
TABLE OF CONTENTS n Introduction .....................................................................................................................................................................2 n General Safety Rules ................................................................................................................................................... 3-4 n Specific Safety Rules..................................................................................................................
GENERAL SAFETY RULES WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. n n SAVE THESE INSTRUCTIONS WORK AREA SAFETY n n Keep work area clean and well lit. Cluttered or dark areas invite accidents.
GENERAL SAFETY RULES n Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. n Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water.
SAFETY RULES FOR CHARGER tain chemicals that can damage, weaken, or destroy plastic. WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. n An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
FEATURES PRODUCT SPECIFICATIONS Motor .................................................................9.6 Volt DC Switch..........................................................Variable Speed No Load Speed ................................................. 0-530/min. Coupler.............................................................. 1/4 in. Hex Charger Input ................................... 120 V, 60 Hz, AC only Charge Rate ............................................................20 min. Torque.
FEATURES KNOW YOUR SCREWDRIVER STICK/PISTOL COMBINATION See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. The screwdriver has been designed so that it can be operated as a stick screwdriver or a pistol screwdriver. DIRECTION OF ROTATION SELECTOR TORQUE ADJUSTMENT RING Your screwdriver has a 16-position clutch. The torque adjustment ring can be turned to select the right amount of torque for your application.
OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool.
OPERATION LED FUNCTION OF CHARGER See Figure 3.
OPERATION TO INSTALL BATTERY PACK See Figure 4. n Place the battery pack in the screwdriver, aligning raised rib on battery pack with groove in the tool’s battery port. n Make sure the latches on each side of the battery pack snap into place and the battery pack is secured to the screwdriver before beginning operation. CAUTION: When placing battery pack in the tool, be sure raised rib on battery pack aligns with the bottom of the screwdriver and latches into place properly.
OPERATION DIRECTION OF ROTATION SELECTOR DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE/CENTER LOCK) See Figure 6. The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger. With the screwdriver held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for driving. The driving direction is reversed when the selector is to the right of the switch trigger.
OPERATION STICK/PISTOL POSITION See Figures 8 - 9. The screwdriver has been designed so that it can be used as a stick screwdriver or a pistol screwdriver. A pivot locking button is located on the side of the screwdriver. TO LOCK To place the screwdriver in stick position: Hold in normal operating position, slide pivot locking button down and twist front housing fully to the right.
OPERATION RELEASE COUPLER REMOVING BITS See Figure 10. n Lock the switch trigger by placing the direction of rotation selector in the center position. 3 PULL COUPLER FORWARD n Remove the battery pack from the screwdriver. 1 n Pull the coupler away from the screwdriver. n Remove screwdriver bit from the coupler. LOCKING GROOVE INSERT BIT 2 WARNING: Do not drive a screw where there is likely to be hidden wiring behind the surface.
MAINTENANCE GENERAL MAINTENANCE WARNING: Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc.
WARRANTY RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY WHAT IS NOT COVERED Proof of purchase must be presented when requesting warranty service. This warranty applies only to the original purchaser at retail and may not be transferred.
OPERATOR’S MANUAL 9.6 VOLT PIVOTING SCREWDRIVER VARIABLE SPEED/REVERSIBLE R81030 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the motor housing.