OPERATOR’S MANUAL 14.4 Volt 1/2 in. (13 mm) Drill-Driver R83015 Two Speed/Reversible 16 18 20 22 ® X R This new drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, the drill will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying a RIDGID product.
TABLE OF CONTENTS ■ Introduction ..................................................................................................................................................................... 2 ■ General Safety Rules .................................................................................................................................................. 3-4 ■ Specific Safety Rules ............................................................................................................
GENERAL SAFETY RULES ■ Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. ■ Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations. ■ Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
GENERAL SAFETY RULES ■ When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. SERVICE ■ Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER c. That wire size is large enough for AC ampere rating of charger as specified below: Cord Length (Feet) 25' 50' 100' Cord Size (AWG) 16 16 16 Note: AWG = American Wire Gage ■ Do not operate charger with a damaged cord or plug. If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury. WARNING: Read and understand all instructions.
SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SPECIFICATIONS Chuck ............................................................................................................................................... 1/2 in. (13 mm) Keyless Motor .................................................................................................................................................................. 14.4 Volt DC Switch ......................................................................................................................................
FEATURES Before using this tool, familiarize yourself with all operating features and safety requirements. However, do not let familiarity with the tool make you careless. TWO SPEED GEAR TRAIN The drill-driver has a two-speed gear train designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of your drill to select either LO (1) or HI (2) speed. WARNING: Exercise caution when using this tool.
FEATURES TWO-SPEED GEAR TRAIN (HI-LO) 16 18 20 22 KEYLESS CHUCK BIT STORAGE DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE/LOCK OFF) 16 18 20 22 BATTERY PACK TORQUE ADJUSTMENT RING DUAL PORT CHARGER 30 min e r te n P o worrienntatio ? C me A li a te r a lu lue r E v Evavalua E go g in d e a r a na rg C hC a rgc h 4-1/8 in. En 30 min ll to . F u p le m a x m C o a rg e Ch Fig.
OPERATION WARNING: Do not allow familiarity with the drill-driver to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. 30 min CHARGING BATTERY PACK e r te n P o worrienntatio ? C me A li The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the light on front of charger changes from flashing green to continuous green.
OPERATION LED FUNCTION OF CHARGER See Figure 3.
OPERATION FORWARD/REVERSE/LOCK OFF SELECTOR TO INSTALL BATTERY PACK ■ ■ ■ Lock the switch trigger on the drill by placing the direction of rotation (forward-reverse) selector in center position. See Figure 4. Place battery pack in the drill. Align raised rib on battery pack with the groove inside the drill. See Figure 5. Make sure the latches on each side of your battery pack snap in place and battery pack is secured in the drill before beginning operation.
OPERATION TWO SPEED GEAR TRAIN (HI-LO) REVERSIBLE See Figure 4. This tool has the feature of being reversible. The direction of rotation is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch for drilling. The drilling direction is reversed when the selector is to the right of the switch. When the selector is in center position, the switch trigger is locked.
OPERATION INSTALLING BITS UNLOCK (RELEASE) 16 18 20 22 See Figure 9. ■ Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. ■ Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws. ■ Insert drill bit straight into chuck the full length of the jaws as shown in figure 10.
OPERATION ADJUSTABLE TORQUE CLUTCH ADJUSTING RING TO DECREASE TORQUE 20 22 This drill is equipped with an adjustable torque clutch for driving different types of screws into different materials. The proper setting depends on the type of material and the size of screw you are using. TO ADJUST TORQUE 16 18 ■ Identify the twenty four torque indicator settings located on the front of the drill. See Figure 11. ■ Rotate adjusting ring to the desired setting. • 1-4 For driving small screws.
OPERATION DRILLING See Figure 13. When drilling hard smooth surfaces use a center punch to mark desired hole location. This will prevent the drill bit from slipping off center as the hole is started. However, the low speed feature allows starting holes without center punching if desired. To accomplish this, simply operate the drill at a low speed until the hole is started. The material to be drilled should be secured in a vise or with clamps to keep it from turning as the drill bit rotates.
OPERATION CHUCK REMOVAL 16 18 20 22 See Figures 14, 15, and 16. The chuck must be removed in order to use some accessories. To remove: ■ Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. ■ Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely. ■ Tap the hex key sharply with a mallet in a clockwise direction. See Figure 14. This will loosen the screw in the chuck for easy removal.
MAINTENANCE BATTERIES WARNING: The battery pack for your tool is equipped with nickelcadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this tool have been designed to provide maximum trouble free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries.
WARRANTY RIDGID® HAND HELD AND STATIONARY POWER TOOL LIMITED THREE YEAR WARRANTY AND 90-DAY SATISFACTION GUARANTEE POLICY This product is manufactured under license from Ridgid, Inc. by One World Technologies, Inc. All warranty communications should be directed to One World Technologies, Inc. at (tollfree) 1-866-539-1710. WHAT IS NOT COVERED This warranty applies only to the original purchaser at retail and may not be transferred.
OPERATOR’S MANUAL 14.4 Volt 1/2 in. (13 mm) Drill-Driver R83015 Two Speed/Reversible ® Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgidwoodworking.com. The model number of this tool is found on a plate attached to the motor housing.