Table of Contents Section Page Table of Contents ........................................ 2 Safety Instructions For Table Saw ............. 3 Safety Signal Words .................................. 3 Before Using The Saw ............................... 3 When Installing Or Moving The Saw ............ 4 Before Each Use ........................................... 4 To Reduce the Risk of Injury From Jams, Slips Or Thrown Pieces (Kickbacks Or Throwbacks) .............................................
Safety Instructions For Table Saw Safety is a combination of common sense, staying alert and knowing how your table saw works. Read this manual to understand this table saw. Safety Signal Words could be seriously injured or killed. CAUTION: means if the safety information is not followed someone may be injured. DANGER: means if the safety information is not followed someone will be seriously injured or killed.
Safety Instructions For Table Saw (continued) • Find and read all the warning labels found on the saw (shown below). When Installing Or Moving The Saw • Support the saw so the table is level and the saw does not rock. • Put the saw where neither operator nor bystanders must stand in line with the sawblade. • To reduce the risk of injury from electrical shock, make sure your fingers do not touch the plug’s metal prongs when plugging in or unplugging the saw. • Never Stand On Tool.
spreader is in line with sawblade (See “Assembly-Aligning Blade Guard” section). • Remove adjusting keys and wrenches. Form a habit of checking for and removing keys and adjusting wrenches from table top before turning saw on. • Make sure all clamps and locks are tight and no parts have excessive play. • If any part is missing, bent or broken in any way, or any electrical part does not work properly, turn the saw off and unplug the saw. • Replace damaged or missing parts before using the saw again.
Safety Instructions For Table Saws (continued) and kick back. • Make sure there’s no debris between the workpiece and its supports. • Use extra caution with large, very small or awkward workpieces. • Use extra supports (tables, saw horses, blocks, etc.) for any workpieces large enough to tip when not held down to the table top.
• Reduce the risk of hand positions where a sudden slip could cause fingers or hand to move into a sawblade or other cutting tool. • Don’t overreach. Always keep good footing and balance. • Push the workpiece against the rotation of the blade, never feed material into the cutting tool from the rear of the saw. • Always push the workpiece all the way past the sawblade. • As much as possible, keep your face and body to one side of the sawblade, out of line with a possible kickback or throwback.
Safety Instructions For Table Saws (continued) Before Leaving The Saw. • Turn the saw off. • Wait for blade to stop spinning. • Unplug the saw. • Make workshop child-proof. Lock the shop. Disconnect master switches. Remove the yellow switch key. Store it away from children and others not qualified to use the tool. To reduce the risk of throwback of cut off pieces. • Use the guard assembly. To remove loose pieces beneath or trapped inside the guard. • Turn saw “OFF”. • Remove switch key.
Additional Safety Instructions For: Before Starting Crosscut Type Cuts. • Never use the rip fence when cross- • Use jigs or fixtures to help hold any piece too small to extend across the cutting. full length of the miter gauge face • An auxiliary wood facing attached to during the cut. This lets you properly the miter gauge can help prevent hold the miter gauge and workpiece workpiece twisting and throwbacks. and helps keep your hands away Attach it to the slots provided. Make from the blade.
Glossary of Terms for Woodworking (continued) Push Stick A device used to feed the workpiece through the saw during narrow ripping type operations which helps keep the operator’s hands well away from the blade. Push Block A device used for ripping type operations too narrow to allow use of a push stick. Rabbet A notch in the edge of a workpiece. (A type of non-through cut) Resin A sticky, sap based substance that has hardened.
Motor Specifications and Electrical Requirements The A-C motor used on this tool is a universal non-reversible type, having the following specifications. Power Supply and Motor Specifications WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15amp branch circuit.
Motor Specifications and Electrical Requirements (continued) A temporary adapter may be used to connect this plug to a 2-prong outlet as shown if a properly grounded three prong outlet is not available. This temporary adapter should be used only until a properly grounded three prong outlet can be installed by a qualified electrician. The green colored rigid ear, lug or the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box.
CAUTION: To reduce the risk of motor damage, this motor should be blown out or vacuumed frequently to prevent sawdust buildup which will interfere with normal motor ventilation. 1. Frequent “blowing” of fuses or tripping of circuit breakers may result if: a. Motor is overloaded - Overloading can occur if you feed too rapidly or if saw blade is dull or misaligned. b. Motor circuit is fused differently from recommendations - Always follow instructions for the proper fuse/ breaker.
Unpacking and Checking Contents Unpacking Separate saw and all parts from packing materials and check each one with the illustration and the “List of Loose Parts” to make certain all items are accounted for, before discarding any packing material. Call 1-866-539-1710 or E-mail us at info@ridgidwoodworking.com if any parts are damaged or missing.
Getting to Know Your Table Saw 3 Table Extension Lock Lever 15 Miter Gauge 1 Rip Fence 4 Sliding Table Extension 14 Table 5 Rip Fence Front Fence Rail Storage 2 MicroAdjust 12 On-Off Rip Fence Switch 13 Thermal 6 MIter Gauge Overload Device Storage 11 Blade Tilt Lock Lever 9 Elevation/Bevel 8 Blade Tilt Handwheel Scale 10 Blade Elevation 7 Two-Piece Base Lock Knob 16 Blade Guard 17 Ind-I-Cut 18 Carry Handles Rear Fence Rail 19 Table Insert 23 Blade Guard Storage for Non-thru Cuts
Getting to Know Your Table Saw 1. Rip Fence...is locked in place by pushing the lock lever down until the lever rests on the stop. To move the fence, lift the lock lever and grasp the fence with one hand at the front. “T” slots are provided in the rip fence for attaching a wood facing when using the dado head, or molding head. 2. Micro-Adjust Rip Fence...allows the operator to accurately adjust the rip fence using only one hand. To move the fence push in on the micro-adjust knob and rotate. 3.
b. To turn saw OFF, PUSH lever in. Never leave the saw until the cutting tool has come to a complete stop. c. To lock switch in OFF position, hold switch IN with one hand, REMOVE key with other hand. WARNING: For your own safety, lower blade or other cutting tool below table surface. (If blade is tilted, return it to vertical, 90°, position.) Always lock the switch “OFF”. When saw is not in use, remove key and keep it in a safe place.
Getting to Know Your Table Saw (continued) 17. Ind-I-Cut The plastic disk embedded in the table in front of the sawblade, is provided for marking the location of the “sawcut” (kerf) on the workpiece. Check disk location: If it is above table surface, place a piece of hardwood on top of it and tap it down with a hammer. 18. Carry Handles...grasp the table here when picking up the saw. 19. Table Insert Is removable for removing or installing blade or other cutting tools.
Blade Guard Storage Holds the blade guard when making nonthru cuts and transporting saw. Slide blade guard in as shown. Snap bottom edge of clear basket between latches on base. Guard Latches Wrench/Blade Storage Conveniently stores arbor wrenches as well as an extra sawblade. Secure wrenches and sawblade with blade storage washer and wing nut. Extra washers are provided to separate blades and prevent tooth damage.
Alignment Tools Needed Combination Square must be true. Check it’s accuracy as shown below. Phillips Screwdriver Draw light line on Select the straight edge of board along edge 3/4” thick board. This edge must be perfectly straight. Combination Wrenches 3/8, 7/16 In. 1/2 In. 9/16 In. NOTE: The square and Combination straight edge are used to Combination align the saw. They must Square Square be accurate if the saw is to be aligned properly. Hex “L” Wrenches Should be no gap or overlap here when 3/32 In.
Checking Heeling Adjustment or Parallelism of Sawblade to Miter Gauge Groove While cutting, the material must move in a straight line parallel to the sawblade. Therefore, both the miter gauge groove and the rip fence must be parallel to the sawblade. Marked Tooth WARNING: The blade must be parallel to the miter gauge groove. Misaligned blades could bind on workpiece. Workpiece could suddenly kickback. You could be cut or hit.
Alignment (continued) NOTE: Always review the section "Checking Blade Parallel to the Miter Gauge Groove" before proceeding with this section. 7. Loosen 1/2 turn the four alignment screws in the top of table next to the sawblade. This will allow the mechanism below the table to be shifted sideways. CAUTION: Blade tips are sharp, to move, grasp blade as shown to avoid injury. 8. Push on side of blade and move it to either the right or left as needed to make the square touch the same amount front and rear.
Checking Blade Tilt, or Squareness of Blade to Table When the bevel pointer is pointing directly to the “0” mark on the bevel scale, the sawblade should make a square cut 90° to the table. WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet. Square Blade To Check For Squareness, 90° Position 1. Raise blade all the way up. 2. Loosen the blade tilt lock lever and push the elevation wheel in and to the left as far as possible and tighten the blade tilt lock lever. 3.
Alignment (continued) To check for alignment, 45° Position 1. Loosen the blade tilt lock lever and push elevation wheel in and to the right as far as possible and tighten the blade tilt lock lever. 2. Place an accurate square against blade. Make sure square is not touching the tip of one of the saw teeth. Scale Screws A. If blade is 45° to table; 1. Check pointer. If pointer does not point to the 45° mark on the scale, the scale must be adjusted. 2.
Adjusting Rip Fence Guide Bars Aligning Rip Fence Guide Bars 1. Position rip fence over right end of main table. While holding up rear of rip fence engage front end of rip fence onto the front guide bar. Now lower rip fence down onto table. 2. Open owners manual so that 8 pages are separated from the rest of the book. Use these pages like a feeler gage to set the spacing between the bottom of the fence and the table top. 3.
Alignment (continued) Aligning Sliding Table Extension Combination Square 1. Lock table extension lever. 2. Loosen the four nuts underneath the sliding table extension. 3. Use a combination square to make sure the top of the sliding table extension is the same height as the main table. 4. Tighten four nuts. Recheck and readjust if necessary. Rip Fence Alignment Adjustment WARNING: A misaligned fence can cause kickbacks and jams.
Rip Fence Lock Lever Adjustment The rip fence lock lever, when locked down, should hold the rip fence securely. The lever should not be difficult to push down and lock. To assure proper fence lock adjustment: a. Raise lock lever and push fence head toward rear of saw. b. Hold fence head down onto front guide bar while lifting rear of fence up and down. c. Tighten adjusting nut until fence clamp just barely touches rear guide bar. d.
Alignment (continued) Checking Sliding Table Extension Lock the table extension lock lever. Pullpush on the sliding table extension. It should not move. Hex Locking Nut Front Hex Coupling WARNING: To reduce the risk of thrown workpiece, do not use with extension lock lever unlocked. If the sliding table extension moves when locked: 1. Release the table extension lock lever. 2. Find the front hex coupling located underneath the front table. 3. Loosen the hex locking nut. 4.
Aligning Blade Guard IMPORTANT: To work properly, the spreader must always be adjusted so the Wood cut workpiece will pass on either side of Blade Kerf the spreader without binding or skewing to the side. NOTE: The spreader is thinner than the width of the cut (kerf) by approximately six thicknesses of paper. 1. Raise blade all the way up, making sure it is square with table. Spreader 2. Use a wrench to loosen the screw that secures the spreader support to Paper the spreader mount. 3. Raise blade guard.
Alignment (continued) Removing and Installing Sawblade WARNING: To reduce the risk of injury from accidental start, turn switch “OFF” and remove plug from power source outlet before removing or installing sawblade. Open End Arbor Shaft Wrench a. Raise blade guard, remove insert, Tighten elevate blade to its highest point. b. To remove blade, hold arbor wrench securely, pull arbor nut wrench towards the front of the table. c.
Miter Gauge Alignment NOTE: The graduations are manufactured to very close tolerances which provide ample accuracy for fine woodworking. In some cases where extreme accuracy is required, when making angle cuts, for example, make a trial cut and then recheck it. Knob Miter Gauge Head Pointer Bar There are adjustable screw stops for the stop pin at 0° and 45° right and left positions for conveniently setting the miter gauge to cut miters at these standard angles. Adjusting Stop Screws A.
Alignment (continued) Marking the Ind-I-Cut: a. With blade 90° (square to table) and miter gauge in left groove, cross cut a piece of wood holding the wood firmly against miter gauge. b. Pull miter gauge back until freshly cut edge of wood is over disk. Using a sharp pencil, mark a line on disk at freshly cut edge of wood. c. With miter gauge in right hand groove, follow same procedure and mark another line on disk. d. These lines indicate the “path” of the cut (kerf) made by the sawblade. e.
Mounting Your Saw Mounting Table Saw to Workbench or Legset WARNING: To reduce the risk of injury from accidental start, make sure switch is "OFF" and plug is not connected to power source outlet. Workbench Surface 4" 16-3/4" WARNING: To reduce the risk of injury from kickback or saw movement the saw must be properly secured to a sturdy workbench, cabinet or legset. Casters if provided on the cabinet or legset must be locked during saw operation.
Mounting Your Saw (continued) Mounting Table Saw to RIDGID Universal Power Tool Legset #AC9910 1. Assemble legset per instructions. 2. Locate the four (4) “TS” layout points on the particle board tables. 3. Drill the four (4) above holes. 4. Insert four (4) 1/4-20 screws that are long enough for washers and nuts which will properly secure the table saw to the legset. Tighten hardware. NOTE: Mounting hardware (bolts, nuts, washers, etc.) are not supplied with the saw.
Safety Instructions for Basic Saw Operations Before Each Use Inspect your saw. • To reduce the risk of injury from accidental starting, turn the switch off, unplug the saw, and remove the switch key before raising or removing the guard, changing the cutting tool, changing the setup, or adjusting anything. • Check for alignment of moving parts, binding of moving parts, breakage of parts, saw stability, and any other conditions that may affect the way the saw works.
Safety Instructions for Basic Saw Operations (continued) • To reduce the risk of burns or other fire damage, never use the saw near flammable liquids, vapors or gases. • To reduce the risk of injury, don’t do layout, assembly, or setup work on the table while blade is spinning. It could cut or throw anything hitting the blade. Plan your work • Use the right tool. Don’t force tool or attachment to do a job it was not designed for. Inspect your workpiece.
• Any power saw can throw foreign objects into the eyes. This can result in permanent eye damage. Always wear safety goggles, not glasses, complying with ANSI Z87.1 (or in Canada CSA Z94.399) shown on package. Everyday eyeglasses have only impact resistant lenses. They are not safety glasses. Safety goggles are available at many local retail stores. Glasses or goggles not in compliance with ANSI or CSA could seriously hurt you when they break.
Safety Instructions for Basic Saw Operations (continued) • Feed the workpiece into the saw To remove loose pieces beneath or only fast enough to let the blade trapped inside the guard. cut without bogging down or bind- • Turn saw “OFF”. ing. • Remove switch key. Before freeing jammed material. • Wait for blade to stop before lifting • Turn switch “OFF”. the guard. • Wait for all moving parts to stop. Before Leaving The Saw. • Turn the saw off. • Unplug the saw.
Push Stick Make the featherboard from a piece of 8” x 24” x 3/4” thick solid wood Make the push stick from a piece of solid wood. Use a piece of 1 x 2 (3/4" x 1-5/8" actual) by 15" long. Slightly Less Than Thickness Of Workpiece Up to 3/8" 24" Kerfs About 5/16" Apart 90° Notch 4-1/2" Push Block (For Use with Auxiliary Fence) 8" 5" At Least 12" There are any number of ways to properly cut your workpieces to make a push block. The following steps describe one way you can make a push block.
Work Feed Devices (continued) Making the handle: • Miter crosscut a piece of 3/4 inch thick plywood to shape and size shown: NOTE: The mitered corners can be any size that looks like the drawing (about 1-1/2" by 1-1/2"). Putting it Together • Using good quality woodworking glue, glue the 3/8" x 3/8" x 2-1/2" piece strip saved earlier to the base as shown. IMPORTANT: Do not use nails or screws. This is to prevent dulling of the sawblade in the event you cut into the push block.
Fence Facing Select a piece of smooth straight wood approximately 3/4 inch thick, and the same length as the rip fence. Attach it to the fence with the three square head bolts, nuts and washers. (See “Hardware for Attaching Wood Facing”) in Repair Parts Figure 4. To remove the facing, loosen the hex nuts, slide the facing toward the rear and out of the fence slot. If the fence facing is for use with feather boards, it will need to be about 8" tall.
Basic Saw Operations Using the Miter Gauge The miter gauge is used when crosscutting, miter cutting, bevel cutting, compound miter cutting, dadoing and when rabbeting across the end of a narrow workpiece. WARNING: For your own safety, always observe the following safety precautions in addition to the safety instructions of pages 3 thru 9 and 35 thru 38. Additional Safety Instructions for Crosscutting Before Starting: • Never use the rip fence when crosscutting except as specifically instructed.
Crosscutting (continued) Miter Gauge Slots are provided in the miter gauge for Head Lock attaching an auxiliary facing to make it Knob easier to cut very long or short pieces. Select a suitable piece of smooth wood, drill two holes through it and attach with screws. Make sure the facing does not interfere with the proper operation of the sawblade guard. When cutting long workpieces, you can make a simple support by clamping a Stop Pin 45° Stop piece of plywood to a sawhorse.
Basic Saw Operations (continued) Miter Crosscutting Miter cutting is cutting wood at an angle other than 90° with the edge of the wood. Follow the same procedure as you would for crosscutting. • Adjust the miter gauge to the desired angle, and lock it. • The miter gauge may be used in either of the grooves in the table. Make sure it is locked.
Using the Rip Fence Ripping, bevel ripping, resawing and rabbeting are performed using the rip fence together with the auxiliary fence/work support, push stick or push block. WARNING: For your own safety, read and always observe all safety precautions listed in manual and on saw. Additional Safety Instructions for Rip Cuts • Never use the miter gauge when ripping • Use a push stick whenever the fence is 2 or more inches from the blade.
Basic Saw Operations (continued) Ripping Definition: Cutting operation along the length of the workpiece. Position the fence to the desired width of rip and lock in place. Before starting to rip, be sure: 1. Rip fence is parallel to sawblade. 2. Spreader is properly aligned with sawblade. 3. Anti-kickback pawls are functioning properly. When ripping long boards or large panels, always use a work support. A simple support can be made by clamping a piece of plywood to a sawhorse.
Ripping (continued) Auxiliary Fence When “width of rip” is narrower than 2" the push stick cannot be used because the guard will interfere...use the auxiliary fence and push block. Attach auxiliary fence to rip fence with two “C” clamps or use “T” slot and hardware. “C” Clamp Push Block Feed the workpiece by hand along the auxiliary fence until the end is approximately 1" past the front edge of the table. Continue to feed using the push block.
Basic Saw Operations (continued) Using Featherboards for Thru Sawing Featherboards are not employed for thru Featherboard sawing operations when using the miter gauge. “C” Clamps Featherboards are used to keep the work in contact with the fence and table as Work shown, and to help stop kickbacks. Support Add a 7-1/2” high flat facing board to the fence, the full length of the fence.
Using Featherboards for Non-Thru Sawing Featherboards are not employed during non-thru sawing operations when using the miter gauge. Use featherboards for all other non-thru sawing operations (when sawblade guard must be removed). Featherboards are used to keep the work in contact with the fence and table as shown and to stop kickbacks. Add a 7-1/2” high flat facing board to the fence, the full length of the fence.
Basic Saw Operations (continued) Resawing Resawing is a rip cut made in a piece of wood through its thickness. The piece is typically positioned on its edge. If the piece is narrower than 3-3/8" it can be resawn in one pass with the blade guard in place. Extra supports or fixtures will be required when the edge resting on the table is too narrow for the piece to be stable or when the fence interferes with the blade guard.
Dadoing Dadoing is cutting a groove into the workpiece. There are a wide variety of dado heads available - be sure and consult the specific instructions included with your dado head. WARNING: For your own safety; always read, understand and follow all directions in the instructional booklet furnished with the dado head. The slot provided for the saw blade in the regular table insert is too small for the dado head to pass through. Therefore, a special dado insert must be purchased.
Basic Saw Operations (continued) Rabbeting Rabbeting is known as cutting out a section of the corner of a piece of material, across an end or along an edge. To make a rabbet requires cuts which do not go all the way through the material. Therefore, the blade guard must be removed. 1. Remove blade guard. 2. For rabbeting along an edge (long way of workpiece) as shown add facing to rip fence approximately as high as the workpiece is wide.
It is necessary to use an auxiliary fence when shaping edges of a workpiece. Position the auxiliary fence over the cutterhead with the cutter head below the surface of the saw table. Turn the saw “ON” and slowly raise the cutterhead. The cutterhead will then cut its own groove in the auxiliary fence. Molding Molding is cutting a shape on the edge or face of the workpiece. With a molding head and a selection of different knife shapes it is possible for almost any kind of molding (base, cove, bead, etc.
Maintaining Your Table Saw pawls are always sharp. To sharpen: 1. Remove blade guard. 2. Rotate pawl toward rear of spreader so that teeth are above top of spreader. Maintenance WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before maintaining or lubricating your saw. Anti-Kickback Pawl • Do not allow sawdust to accumulate inside the saw. Frequently blow out any dust that may accumulate inside the saw cabinet and the motor.
reassemble reverse the procedure. Tighten the screws snugly but do not overtighten. WARNING: To reduce the risk of injury from unexpected starting or electrical shock, unplug the power cord before working on the saw. Lubrication WARNING: To reduce the risk of electrical shock, fire or injury, use only parts identical to those identified in the parts list reassemble exactly as original assembly to reduce the risk of electrical hazards.
Troubleshooting WARNING: For your own protection, turn switch “OFF” and always remove plug from power source outlet before troubleshooting. General Trouble Excessive Vibration Probable Cause Remedy 1. Blade out of balance or 1. Replace blade. damaged Cannot make 1. Miter gauge not square cut when adjusted properly. crosscutting. 1. See “Adjustments” section “Miter Gauge.” Cut binds, burns 1. Dull blade or improper tooth set. or stalls motor 2. Blade is heeling. when ripping. 1.
Motor NOTE: Motors used on wood working tools are particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or “Vacuumed” frequently to prevent interference with normal motor ventilation. Trouble Probable Cause Remedy Excessive Noise 1. Motor 1. Have motor checked by qualified service technician. Repair service is available at your nearest Authorized Service Center. Motor fails to develop full power.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24001 RIDGID parts are available on-line at www.ridgidparts.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24001 RIDGID parts are available on-line at www.ridgidparts.com Figure 1 Always Order by Part Number - not by Key Number Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Part No. Key No.
Repair Parts 14 21 21 21 22 17 52 45 29 32 28 27 46 33 34 30 44 35 26 31 43 25 18 36 24 2 37 3 38 24 23 39 20 19 40 41 48 6 3 2 4 42 1 7 8 5 9 18 15 10 47 13 11 12 51 16 49 50 Parts list for RIDGID 10 Inch Table Saw Model No. TS24001 RIDGID parts are available on-line at www.ridgidparts.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model TS24001 RIDGID parts are available on-line at www.ridgidparts.com Figure 2 Always Order by Part Number - not by Key Number Key No. 1 2 Part No. Key No. Description Part No. 27 827863 Description Screw Set Nylon 10-32 x 3/4 28 827864 Nut Hex Nylon 10-32 29 830412 Arbor Asm 30 9420474 * Screw Hex Ty T 10/32 x 1/2 31 808380-17 * Screw Pan Hd #10 x 3/4 32 827476 Chute Sawdust 33 60249 * Nut Lock 3/8-16 34 60014 * Washer .
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24001 RIDGID parts are available on-line at www.ridgidparts.com Figure 3 - Miter Gauge Assembly 1 2 16 3 4 15 14 5 13 6 12 7 11 8 9 10 Always Order by Part Number - Not by Key Number Key No. – 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Part No. 830338 826506-1 821063-5 826663 824723-1 123069-1 830351 830352 140755-15 824723 818470-4 830350 830354 830353 134530 809813-4 818471-6 Description * * * * * Miter Gauge Asm.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24001 RIDGID parts are available on-line at www.ridgidparts.com Figure 4 - Fence Assembly 1 26 6 5 2 3 4 7 8 25 9 24 23 10 11 12 1 14 20 13 15 22 28 27 16 17 21 20 17 19 18 Always Order by Part Number - not by Key Number Key Part No. No. – 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Key Part No. No. Description 830421 Fence Complete 809492-5 Screw Pan Hd.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24001 RIDGID parts are available on-line at www.ridgidparts.com Figure 5 - Guard Assembly 4 3 4 5 22 1 4 5 2 21 8 6 7 20 18 4 19 17 10 9 11 16 17 18 2 3 12 8 13 15 14 Always Order by Part Number - not by Key Number Key No. Part No. – 1 2 3 4 827499 62519 827646 827648-1 805549 5 6 7 8 9 10 60012 827649-1 62390 802612 826466 827536 Key No.
Notes 65
Notes 66
Notes 67
RIDGID® HAND HELD AND STATIONARY POWER TOOL LIMITED THREE YEAR WARRANTY AND 90 DAY SATISFACTION GUARANTEE POLICY This product is manufactured under license from Ridgid, Inc. by One World Technologies, Inc.. All warranty communications should be directed to One World Technologies, Inc. at (toll free) 1-866-539-1710.