OPERATOR’S MANUAL Work-n-Haul IT Two Wheel Work Stand TM AC9930 For Use With Ridgid TS2400 Table Saw And Ridgid Miter Saws This work stand has been engineered and manufactured to our high standard for dependability, ease of operation and operator safety. When properly cared for, the work stand will give you years of rugged, trouble-free performance. WARNING To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
TABLE OF CONTENTS n Introduction ...................................................................................................................................................................... 2 n Rules for Safe Operation .................................................................................................................................................. 3 n Symbols.............................................................................................................................
RULES FOR SAFE OPERATION n NEVER STAND ON WORKSTAND. Serious injury could occur if the stand tips or you accidentally hit the cutting tool. Do not store any items above or near the stand where anyone might climb on the stand to reach them. n Maximum weight of power tool must not exceed 100 pounds. n Always mount miter saw so the workpiece is positioned in-line with the roller assemblies. n Check to make sure workstand does not rock, slide or move prior to use.
SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
UNPACKING NOTE: Before beginning assembly, check that all parts are included. If you are missing any part, do not assemble this accessory. Call 1-800-4-RIDGID or E-mail us at info@ridgid.com to get the missing part. Sometimes small parts can get lost in packaging material. Do not throw away any packaging until the accessory is completely assembled and attached to your power tool. Check packaging for missing parts before contacting RIDGID.
ASSEMBLY ASSEMBLING THE LOWER FOOT MOVING THE CARRY HANDLE SPRING PIN See Figure 1. See Figures 2 and 3. NOTE: Only ONE spring pin is required at the carry handle end of the stand. This spring pin locks the legs in the set-up or tear-down position. Instructions to change the location of this spring pin are described later in the “Assembly” section of this manual.
ASSEMBLY WORK STAND SET-UP n At the wheel end of the stand firmly grab the lift handle and with the other hand pull the spring pin knob near the right front wheel. See Figures 4, 5, 6 and 7. Before you start n Remove any workpieces from the tool. CAUTION: n If the tool is already assembled to the stand, make sure that it is securely attached to the stand per the instructions in this manual. Do not lift by any part of the miter saw that is attached to the workstand.
ASSEMBLY WORK STAND FOLD DOWN NOTE: You may need to adjust the speed at which you bring up the table in order to get them to unlatch. See Figures 8, 9, 10 and 11. Before you start n From the other end of the stand, pull the spring pin knob and lift stand into the upright position. Push the legs until they lock into place against the bottom of the table. n Remove any workpieces from the tool.
ASSEMBLY SET-UP POSITION MOUNTING POWER TOOLS WARNING: Failure to unplug the tool could result in accidental starting causing possible serious personal injury. Before you start RIDGID TS2400 table saw bolts directly onto this work stand. Most other tools, including miter saws, will need additional supports to aid in attaching a tool to work stand. The hardware and mounting materials shown in this manual are the minimum size recommended for safe attachment of a power tool to this work stand.
ASSEMBLY SEE BOLT VIEW A SEE BOLT VIEW B n Temporarily attach the mounting blocks to work stand with the supplied bolts or 1/4-20 bolts at least 2-1/2 in. long. Secure with washers, lockwashers and nuts. n Locate and drill holes in 2 x 6 mounting blocks and 1 x 4 cross pieces, as shown. Plywood 3/4 in. thick, 24 in. x 27 in. may be used in place of the 1 x 4 s. n Loosen 2 x 6 mounting blocks from work stand table. Attach two 1 x 4 cross pieces to the mounting blocks with 1/4-20 carriage bolts at least 2.
EXPLODED VIEW/REPAIR PARTS 34 * Lubricate if 35 1 Necessary 33 36 32 37 20 30 29 22 21 8 10 * 19 20 9 39 23 38 7 12 4 2 17 13 27 3 11 15 41 15 31 26 24 37 5 14 16 24 6 * 18 25 38 36 * 40 28 Work-N-Haul IT Two Wheel Work Stand Model AC9930 RIDGID parts are at www.ridgidparts.
OPERATOR’S MANUAL Work-n-Haul IT Two Wheel Work Stand TM AC9930 For Use With Ridgid TS2400 Table Saw And Ridgid Miter Saws Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. When ordering repair parts, always give the following information: AC9930 Model No.