SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 1 OWNERS MANUAL WD1850 16 U.S. GALLONS/ 13 CDN. GALLONS PROFESSIONAL WET/DRY VAC For Your Safety: Read all instructions carefully Save this manual for future reference FOR QUESTIONS OR INFORMATION CONTACT US AT 1-800-4-RIDGID (1-800-474-3443) OR www.ridgid.com MAXIMIZE MAXIMIZE VACUUM PERFORMANCE PERFORMANCE WITH WITH A A NEW FILTER FILTER $500rd Gift Ca es Sweepstak Part No. SP6528 Logon to . . . www.ridgidvacs.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 2 Table of Contents Section Page Table of Contents. . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . 2 Safety Signal Words . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking and Checking Carton Contents . . . . . . . . . . . . . . . . . . . . 4 Tools Required . . . . . . . . . . . . . . . . . . . . . 4 Carton Contents List . . . . . . . . . . . . . . . .
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM • Keep cord away from heated surfaces. • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. • Do not use with damaged cord, plug or other parts. • Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. • Do not run Wet/Dry Vac over cord. • Do not handle plug or the Wet/Dry Vac with wet hands.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 4 wear ear protectors when using the vac for extended hours or when using it in a noisy area. For dusty operations, wear dust mask. Use only extension cords that are rated for outdoor use. Extension cords in poor condition or that are too small in wire size can pose fire and shock hazards. When using an extension cord, be sure it is in good condition. Using any extension cord will cause some loss of power.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 5 Carton Contents List Key A B* C* D* E* F G H J K L M N Description Qty Wet/Dry Vac Assembly.................1 Filter Nut ......................................1 High Efficiency Filter ....................1 Filter Cage ...................................1 Float .............................................1 Tug-A-Long Hose.........................1 Utility Nozzle ................................1 Wet Nozzle...................................1 Crevice Nozzle.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 6 Replacement Filter Assembly 1. Carefully slide the filter over the filter cage, sliding it over the center ring covering the 3 slots until the filter stops against the lid. Filter Nut Filter Nut Lever Filter 2. Place filter nut onto threaded stud and tighten it down. Finger tighten only. NOTE: Lever of filter nut should be away from plate as shown.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 7 Drum/Caddy Assembly If any parts are missing or damaged contact Customer Service. Caddy Right Do not assemble until you have all the parts. 1. Insert caddy left and caddy right into the bottom of drum as shown. Light taps with a mallet or hammer may be needed to fully seat both caddies. Caddy Left Drain 2. Install (4) #10 x 1-3/4” screws into matching holes on both right and left side of caddy, securing them to the bottom of the drum.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 8 Drum/Caddy Assembly (continued) 4. Slide open end of axle through caddy left making sure the leg slot lines up with the cradle hole. Slide all the way through the caddy right. Light taps with a mallet may be required to fully insert axle. 5. Install second wheel onto axle with smooth portion of wheel facing outward. Mallet 6. Install the second cap nut. Tap gently until cap nut is firmly seated Wheel Cap 7.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 9 Installing Tool Holder 2. As an alternative storage solution, the tool holder may hang on a wall. Two wall mounting hooks (not provided) must be secured to the wall as shown (sold separately). 1. Install tool holder as shown with extension wand holders facing unit. Tote Snaps Tote Straps (4) Grommet Handle Wall Mount Hook Extension Wand Storage Locations Wall Wet/Dry Vac Assembly 1.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 10 Operation WARNING To reduce the risk of fire or explosion, do not operate this vac in areas with flammable gases, vapors or explosive dust in the air. Flammable gases or vapors include but are not limited to; lighter fluid, solvent type cleaners, oilbase paints, gasoline, alcohol or aerosol sprays. Explosive dusts include but are not limited to; coal, magnesium, grain or gun powder.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 11 Operation (continued) Vacuuming Liquids IMPORTANT: 1. When picking up small amounts of liquid the filter may be left in place. 2. When picking up large amounts of liquid we recommend that the filter be removed. If the filter is not removed, it will become saturated and misting may appear in the exhaust. 3. After using the vac to pick up liquids, the filter must be dried to reduce the risk of possible mildew and damage to the filter. 4.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Blowing Feature Your vac features a blowing port. It can blow sawdust and other debris. Follow the steps below to use your vac as a blower. Page 12 4. Turn vac on and you are ready to use your vac as a blower. WEAR YOUR FORESIGHT IS WARNING: Always wear safety goggles complying with ANSI Z87.1 (or in Canada, CSA Z94.3) before using as a blower.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 13 Maintenance Wet Filter Filter After filter is removed, run water through the filter from a hose or spigot. Take care that water pressure from the hose is not strong enough to damage filter. Remember: To dry a filter quickly, reinstall the filter on the vac and allow the unit to run for approximately 10 minutes. The clean air rushing through the filter will dry it.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 14 Filter Replacement Which Replacement Filter Meets Your Needs? Filter System with Filter System with Microban ¨ Choosing a filter is as easy as 1, 2, 3...
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 15 MAXIMIZE VACUUM PERFORMANCE WITH A NEW FILTER Typical Replacement Frequency is 2 Times Per Year Log on to www.ridgidvac.com/filterclub to Join Our Filter Club and/or Enter Our $500 Home Depot Gift Card Sweepstakes.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 16 Repair Parts 16 Gallon Professional Wet/Dry Vac Model Number WD18500 RIDGID parts are available on-line at www.ridgidparts.com Always order by Part Number - Not by Key Number Key No. Part No.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 17 RIDGID parts are available on-line at www.ridgidparts.com WARNING SERVICING OF DOUBLE-INSULATED WET/DRY VAC In a double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a doubleinsulated Wet/Dry Vac requires extreme care and knowledge of the system, and should be done only by qualified service personnel.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 18 Repair Parts Parts List for Wet/Dry Vac Cart RIDGID parts are available on-line at www.ridgidparts.com Always order by Part Number - Not by Key Number Key No. Part No.
SP6528-2 16Gallon.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 22 Indice Sección Página Sensor de rendimiento del filtro . . . . . . . . . . . 31 Vaciado del tambor . . . . . . . . . . . . . . . . . . . . 31 Traslado de la aspiradora para mojado/seco . . 31 Dispositivo de soplado . . . . . . . . . . . . . . . . . . 32 Accesorios y almacenamiento. . . . . . . . . . . . . . . 32 Enrollado del cordón . . . . . . . . . . . . . . . . . . . 32 Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Filtro . . . . .
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM • No desenchufe la aspiradora tirando del cordón. Para desenchufarla, agarre el enchufe, no el cordón. • No utilice la aspiradora si tiene dañado el cordón, el enchufe u otras piezas. • No tire del cordón ni lleve la aspiradora por el cordón, no utilice el cordón como asa, no cierre una puerta sobre el cordón ni tire del cordón alrededor de bordes afilados o esquinas afiladas. • No utilice la aspiradora para mojado/seco sobre el cordón.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 24 Para operaciones que generan polvo, use una máscara antipolvo. Utilice únicamente cordones de extensión que tengan capacidad nominal para uso a la intemperie. Los cordones de extensión que estén en malas condiciones o cuyo tamaño de alambre sea demasiado pequeño pueden conllevar peligros de incendio y sacudidas eléctricas. Cuando utilice un cordón de extensión, asegúrese de que esté en buenas condiciones.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 25 Lista del contenido de la caja de cartón Clave A B* C* D* E* F G H J K L M N Descripción Cant. Ensamblaje de la aspiradora para mojado/seco ..................................1 Tuerca del filtro ..........................................1 Filtro de alta eficacia...................................1 Jaula del filtro ...........................................1 Flotador .....................................................1 Manguera arrastrable ...............
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 26 Ensamblaje de un filtro de reemplazo 1. Deslice cuidadosamente el filtro sobre la jaula del filtro, deslizándolo sobre el anillo central que cubre las 3 ranuras hasta que el filtro se detenga contra la tapa. Tuerca del Filter Nutfiltro Palanca de Filter Nut laLever tuerca del filtro Filtro Filter 2. Coloque la tuerca del filtro en el espárrago roscado y apriétela hacia abajo. Apriétela solamente con los dedos.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 27 Ensamblaje del tambor/base de soporte Si cualquiera de las piezas falta o está dañada, póngase en contacto con Servicio al Cliente. Base de Caddy soporte Right derecha No monte la aspiradora hasta que tenga todas las piezas. 1. Introduzca la base de soporte izquierda y la base de soporte derecha en la parte inferior del tambor, de la manera que se muestra en la ilustración.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 28 Ensamblaje del tambor/base de soporte (continuación) 4. Deslice el extremo abierto del eje a través de la base de soporte izquierda, asegurándose de que la ranura de la pata se alinee con el agujero de la cuna. Deslice dicho extremo completamente a través de la base de soporte derecha. Es posible que se requieran golpes ligeros con un mazo para introducir completamente el eje. Mazo Mallet 5.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 29 Instalación del portaherramientas 2. Como solución alternativa de almacenamiento, el portaherramientas puede colgar de una pared. Se deben sujetar firmemente a la pared dos ganchos de montaje (no suministrados) de la manera que se muestra en la ilustración (los ganchos se venden por separado). 1. Instale el portaherramientas de la manera que se muestra en la ilustración, con los portatubos extensores orientados hacia la unidad.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 30 Funcionamiento ADVERTENCIA Para reducir el riesgo de incendio o explosión, no utilice esta aspiradora en áreas en las que haya gases o vapores inflamables, ni polvo explosivo en el aire. Los gases o vapores inflamables incluyen pero no están limitados a: líquido encendedor, limpiadores tipo disolvente, pinturas a base de aceite, gasolina, alcohol o rociadoras de aerosol.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 31 Funcionamiento (continuación) 6. Para ajustar las barras indicadoras de vuelta a la posición original completamente verde, oprima el botón de restablecimiento del sensor. NOTA: No oprima el botón de restablecimiento del sensor mientras la aspiradora para mojado/seco esté en marcha. Esto podría dañar el sensor de rendimiento del filtro. 7. Oprima el botón de restablecimiento del sensor hasta que se vean todas las barras verdes.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 32 Dispositivo de soplado 4. Encienda la aspiradora y estará lista para utilizarse como soplador. La aspiradora cuenta con un orificio de soplado. Puede soplar aserrín y otros residuos. Siga los pasos que se indican a continuación para usar la aspiradora como soplador. ADVERTENCIA: Use siempre anteojos de seguridad que cumplan con la norma ANSI Z87.1 (o en Canadá, con la norma CSA Z94.3) antes de utilizar la aspiradora como soplador.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 33 Mantenimiento Filtro Filtro mojado Después de quitar el filtro, haga pasar agua a través de él usando una manguera o desde una espita. Tenga cuidado de que la presión del agua procedente de la manguera no sea lo suficientemente fuerte como para dañar el filtro. Recuerde: Para secar rápidamente un filtro, reinstale el filtro en la aspiradora y deje que la unidad funcione durante aproximadamente 10 minutos.
SP6528-2 16Gallon.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 35 MAXIMICE EL RENDIMIENTO DE LA ASPIRADORA CON UN FILTRO NUEVO La frecuencia típica de reemplazo es de 2 veces al año Sorte o de de Re Tarjetas g 500 d alo de ólare s Conéctese a www.ridgidvac.com/filterclub para hacerse miembro de nuestro Club de Filtros y/o inscribirse en nuestro Sorteo de Tarjetas de Regalo de Home Depot por valor de US$ 500.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 36 Piezas de repuesto Aspiradora para mojado/seco profesional de 16 galones Número de modelo WD18500 Las piezas RIDGID se encuentran disponibles en línea conectándose a www.ridgidparts.com Pida siempre por número de pieza —no por número de clave No. de clave No.
SP6528-2 16Gallon.qxd 6/15/07 02:05 PM Page 37 Las piezas RIDGID se encuentran disponibles en línea conectándose a www.ridgidparts.com ADVERTENCIA SERVICIO DE AJUSTES Y REPARACIONES DE UNA ASPIRADORA PARA MOJADO/SECO CON AISLAMIENTO DOBLE En una aspiradora para mojado/seco con aislamiento doble se proporcionan dos sistemas de aislamiento en vez de conexión a tierra.
SP6528-2 16Gallon.