User manual

44
fig. 14
[EN] L-N Polarisation is recommended
Blu=Blue / Marrone=Brown / Nero=Black / Rosso=Red/ Bianco=White /
Viola=Violet /
Grigio=Grey
A = 24V Low voltage ambient thermostat jumper
B = Gas valve
C = Ignition/Detection electrode
D = Fuse 3.15A F
MP Control board
P1 Potentiometer to select off - summer - winter . reset / temperature
heating
P2 Potentiometer to select domestic hot water set point
P3 Potentiometer to select temperature regulation curve
JP1 Bridge to enable knobs for calibration
JP2 Bridge to reset the heating timer and log maximum electrical heating
in calibration
JP3 Bridge to select MTN - LPG
JP4 Absolute domestic homt water thermostat selector
LED Led 1 (green) to indicate operation status or temporary stop
Led 2 (yellow) to indicate preheating is ON (not used)
Led 3 (red) to indicate permanent lockout status
CN1-CN12 Connectors (CN4 not used - CN6 external probe/instrument
panel kit – CN7 local valve kit)
F1 Fuse 2A T
F External fuse 3.15A F
M3 Terminal board for external connections
T.A. Ambient thermostat
TRX Remote ignition transformer
VFan
P.F. Air pressure switch
S.R. Primary circuit temperature probe (NTC)
T.L. Limit thermostat
OPE Gas valve operator
P Pump
FL Domestic hot water flow switch
S.S. Domestic hot water circuit temperature probe (NTC)
PA Heating pressure switch (water)
MOD Modulator
[F] “ L-N ” Il est conseillé d’utiliser la polarisation “ L-N ”.
Bleu= Blu/ Marron=Marrone/ Noir=Nero/ Rouge=Rosso/ Blanc=Bianco/
Violet=Viola/
Gris=Grigio/
A = Jumper du thermostat dans un environnement de 24V
B = Soupape gaz
C = Électrode d’allumage/détection
D = Fusible 3.15A F
MP Carte de commande
P1 Potentiomètre de sélection off - été - hiver – réarmement/température
chauffage
P2 Potentiomètre de sélection point de consigne sélection point de
consigne sanitaire
P3 Potentiomètre de sélection courbes de régulation thermique
JP1 Shunt activation poignées au réglage
JP2 Shunt mise à zéro minuterie chauffage et mémorisation du chauffage
électrique maximum en réglage
JP3 Shunt sélection MTN - GPL
JP4 Sélecteur des thermostats absolus sanitaire
LED Led 1 (verte) signalisation de l’état fonctionnement ou arrêt provisoire
LED 2 (jaune) signalisation de préchauffage ON (non utilisé)
LED 3 (rouge) signalisation état de blocage définitif
CN1÷CN12 Connecteurs de branchement (CN4 non utilisé - CN6 kit sonde
extérieure/tableau de commande – CN7 kit robinet de zone)
F1 Fusible 2A T
F Fusible externe 3.15A F
M3 Bornier pour branchements externes
T.A. Thermostat d’ambiance
TRX Transformateur d’allumage à distance
V Ventilateur
P.F. Pressostat air
S.R. Sonde (NTC) de température du circuit primaire
T.L. Thermostat limite
OPE Opérateur soupape gaz
P Pompe
FL Fluxostat sanitaire
S.S. Sonde (NTC) de température du circuit sanitaire
PA Pressostat chauffage (eau)
MOD Modulateur
A
B
C
D