Need to speak to an expert? 1 (201) 379-4900 · RIF6.com/support · support@RIF6.
TABLE OF CONTENTS 04 08 14 15 Important Safety Instructions Operating Instructions Specifications Contact Us 06 12 15 Description of Parts Troubleshooting Warranty Information
IMPORTANT SAFETY INSTRUCTIONS • Make sure the record player is properly ventilated and air circulates freely around the unit. Do not place the unit on a thick carpet, bed, or any place where ventilation holes may be obstructed. Leave at least 4 inches of clearance around the unit.
IMPORTANT SAFETY INSTRUCTIONS FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
DESCRIPTION OF PARTS 1 2 3 4 5 16 6 17 7 8 DC 12V 19 9 LP BT AUX BTT MODE 12 15 14 RCA OUT AUX IN AUX OUT 18 11 10 13 RECORD PLAYER | 6 22 20 21 23
DESCRIPTION OF PARTS 1 Turntable Platter 13 Bluetooth-In Indicator 2 45rp Record Adapter – Use it when playing a 45rpm record with a cut out center 14 Mode Knob 3 Tonearm – Press to select a source: LP, Bluetooth In (BT), and Aux In if available 4 Tonearm Lift Lever – Press and hold for 2-3 seconds to select Bluetooth Output (BTT) 5 LP Auto Stop On / Off Selection 6 Speed Selection: 33.
OPERATING INSTRUCTIONS Initial Setup 1. 2. 3. Place the unit on a flat and level surface that is stable and free from vibration. Remove the cable tie that is holding the tonearm. Connect the AC adapter to the power jack of the unit. Note: • This product should only be operated by the type of power source indicated on the rating label. • Plug the AC power adapter to a power outlet after assembly is completed. Before turning the power on, check that all the connections are correct.
OPERATING INSTRUCTIONS Playing a Record 1. 2. 3. 4. 5. Press and hold the Power Volume Knob (11) for 2-3 seconds to turn the unit on. Press the Mode Knob (14) to set the unit to LP mode. The mode indicator will light up. Set the Speed Switch to your desired speed. Place a record on the turntable. If necessary, use the 45 RPM adapter. Remove the stylus protector from the stylus assembly.
OPERATING INSTRUCTIONS Connecting to a Bluetooth Device 1. 2. 3. 4. 5. Press and hold the Power Volume Knob (11) for 2-3 seconds to turn on the power. Press the Mode Knob (14) and select Bluetooth Mode (BT). The Bluetooth indicator will start flashing. Turn on the Bluetooth feature of your audio device. Search for "RIF6 Record Player" and start pairing with the unit. Once your device is successfully paired with the unit, you will hear a short confirmation sound from the unit.
OPERATING INSTRUCTIONS RCA Jack The RCA Jack connects directly to a pair of active/powered speakers or the appropriate input for a stereo system. To connect the RCA Jack, make sure the red plug is connected to the right channel and the white plug is connected to the left channel. Note: The RCA Jack is not designed to be connected directly to the passive/underpowered speakers. If connected to the passive speakers, the volume level will be very low.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION General No power No sound output from the built-in speakers The unit fails to respond No power at the outlet Try another power outlet The power adapter is not connected correctly Connect the power adapter to the unit and wall outlet correctly The POWER ON/OFF knob is on the "Power Off" position Press and hold the POWER knob for 2-3 Seconds to turn the unit on Wrong power adapter Ensure that you are using the correct Power Adapter that was included
TROUBLESHOOTING PROBLEM Noise or sound is distorted POSSIBLE CAUSE SOLUTION The speed selector is set incorrectly Set the speed at 33 1/3, 45, or 78 rpm The stylus is abraded after long time usage Replace it with the spare stylus The volume is set too high on the RIF6 Record speakers Lower the volume on the RIF6 Record speakers The volume is set too high in Aux-In or Bluetooth mode Turn down the playback volume of the sound source The quality of the sound file (mp3) is poor Try another sound fi
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Bluetooth-Out / BTT Cannot connect or pair with Bluetooth speakers This unit does not choose "BTT" Bluetooth output mode Ensure the unit is set to BTT mode This BT mode is selected Exit the Bluetooth Input "BT" mode.
WARRANTY INFORMATION RIF6 offers a one-year warranty on all of our products purchased new and unused from RIF6 or an authorized reseller, with an original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faulty manufacturing, parts or workmanship during the one-year warranty period.
learn more at rif6.