RIGOL Quick Guide DP800A Series Programmable Linear DC Power Supply Oct. 2012 RIGOL Technologies, Inc.
RIGOL Guaranty and Declaration Copyright © 2012 RIGOL Technologies, Inc. All Rights Reserved. Trademark Information RIGOL is a registered trademark of RIGOL Technologies, Inc. Publication Number QGH03102-1110 Notices RIGOL products are protected by patent law in and outside of P.R.C. RIGOL reserves the right to modify or change parts of or all the specifications and pricing policies at company’s sole decision. Information in this publication replaces all previously corresponding material.
RIGOL Safety Requirement General Safety Summary Please review the following safety precautions carefully before putting the instrument into operation so as to avoid any personal injuries or damages to the instrument and any product connected to it. To prevent potential hazards, please use the instrument only specified by this manual. Use Proper Power Cord. Only the power cord designed for the instrument and authorized by local country could be used. Ground The Instrument.
RIGOL Do Not Operate in Wet Conditions. In order to avoid short circuiting to the interior of the device or electric shock, please do not operate in a humid environment. Do Not Operate in an Explosive Atmosphere. In order to avoid damages to the device or personal injuries, it is important to operate the device away from an explosive atmosphere. Keep Product Surfaces Clean and Dry. To avoid the influence of dust and/or moisture in air, please keep the surface of device clean and dry.
RIGOL Safety Terms and Symbols Terms in this Manual. These terms may appear in this manual: WARNING Warning statements indicate the conditions or practices that could result in injury or loss of life. CAUTION Caution statements indicate the conditions or practices that could result in damage to this product or other property. Terms on the Product. These terms may appear on the Product: DANGER WARNING CAUTION indicates an injury or hazard may immediately happen.
RIGOL General Care and Cleaning General Care: Do not store or leave the instrument in where the instrument will be exposed to direct sunlight for long periods of time. Cleaning: Clean the instrument regularly according to its operating conditions. To clean the exterior surface, perform the following steps: 1. Disconnect the instrument from all power sources. 2. Clean the loose dust on the outside of the instrument with a lint- free cloth (with a mild detergent or water).
RIGOL Document Overview This manual is used to guide users to quickly understand the front panel, rear panel, user interface and basic operating methods of DP800A series programmable linear DC power supply. You can download the newest version of this manual from www.rigol.com. Format Conventions in this Manual 1 Buttons The function key at the front panel is denoted by the format of “Button Name (Bold) + Text Box” in the manual, for example, Utility denotes the “System Auxiliary Function Setting” key.
RIGOL Contents Guaranty and Declaration .........................................................................I Safety Requirement ................................................................................ II General Safety Summary ........................................................................... II Safety Terms and Symbols ....................................................................... IV General Care and Cleaning .................................................................
RIGOL Quick Start General Inspection 1. Inspect the shipping container for damage Keep the damaged shipping container or cushioning material until the contents of the shipment have been checked for completeness and the instrument has passed both electrical and mechanical tests. The consigner or carrier shall be liable for the damage to instrument resulting from shipment. RIGOL would not be responsible for free maintenance/rework or replacement of the unit. 2.
RIGOL Appearance and Dimensions 2 Figure 1 Front View Unit: mm Figure 2 Side View Unit: mm DP800A Quick Guide
RIGOL Front Panel 1 11 DP800A Quick Guide 2 10 9 8 7 3 6 Figure 3 DP831A Front Panel 4 5 3
RIGOL 1. LCD 3.5 inches TFT display. It is used to display system parameter settings, system output state, menu options, prompt messages, etc. 2. Channel Selection and Output Switch Press this key to select CH1 and set the parameters of this channel, such as voltage, current and overvoltage/overcurrent protection. Press this key to select CH2 and set the parameters of this channel, such as voltage, current and overvoltage/overcurrent protection.
RIGOL 3. Parameter Input Area The parameter input area is as shown in the figure below. This area includes the direction keys (unit selection keys), numeric keyboard and knob. (1) Direction keys and unit selection keys Direction keys: move the cursor. Unit selection keys: when using the numeric keyboard to input parameters, the keys are used to enter the voltage units V and mV and the current units A and mA. (2) Numeric Keyboard Ring-type numeric keyboard: include numbers 0-9 and the decimal point.
RIGOL 4. Preset 5. OK 6. Back Restore all the settings of the instrument to default values or recall the user-defined channel voltage/current configurations. Confirm the parameter setting. Press and hold this key to lock the front panel keys; at this point, the front panel keys are not available. Press and hold this key again to unlock the front panel keys. When the keyboard lock password is enabled, users need to input the correct password (2012) to unlock the front panel keys.
RIGOL 7. Output Terminals (1) (2) (3) (4) (1) Output the voltage and current of CH1. (2) This terminal is connected to the instrument chassis and ground wire (power cord ground terminal) and is in grounded state. (3) Output the voltage and current of CH2. (4) Output the voltage and current of CH3. Connection methods of the output terminal: B A Method 1: Connect the test lead to A of the output terminal.
RIGOL 8. Function Menu Area Press this key to enter the display parameter setting interface. Users can set the luminosity, contrast and display mode. Press this key to enter the file store and recall interface. You can save, read, delete, copy and paste files. The file types available for storage include state file, record file, timer file and delayer file. The instrument supports internal and external storage and recall. Wherein, external storage supports FAT32 file management system.
RIGOL 9. Display Mode Switch Key Switch between the current display (normal or waveform) mode and dial display mode. 10. Menu Keys The menu keys correspond to the menus above them. Press any menu key to select the corresponding menu. 11. Power Switch Key Turn on or off the instrument.
RIGOL Rear Panel 1 10 2 3 4 9 Figure 4 DP831A Rear Panel 5 6 8 7 Table 1 DP831A Rear Panel Explanation No.
RIGOL To Connect to Power 1. Input power requirement DP800A series power supply can accept three kinds of AC power supplies: 50Hz–60Hz frequency; 100V, 115V and 230V voltages. 2. Check the voltage selector at the rear panel Before connecting to power, make sure that the setting voltage of the voltage selector at the rear panel matches the input voltage. 3. Check the fuse When the instrument leaves factory, proper fuse is installed.
RIGOL To Replace the Fuse To replace the fuse, follow the steps below. 1. Turn off the instrument and remove the power cord. 2. Insert a small straight screwdriver into the slot at the power socket and prize out the fuse seat gently. Fuse Seat Fuse 3. Adjust the power voltage selector manually to select the correct voltage scale. 4.
RIGOL Display Mode DP800A series power supply provides three kinds of display modes (normal, waveform and dial). In the following part, DP831A is taken as an example for illustration. 1. Normal Display Mode After start-up, the instrument enters the normal display mode by default as shown in the figure below. This mode displays the voltages, currents and powers of all channels in number format.
RIGOL 2. Waveform Display Mode Press Display Mode “Wave” to set the display mode to waveform display mode as shown in the figure below. This mode displays the voltage, current and power of the currently selected channel in both number and waveform formats. You can set the voltage, current and overvoltage/overcurrent protection parameters of the channel currently selected. You can also enable or disable the track function if the current channel supports the track function.
RIGOL 3. Dial Display Mode Press Display Mode “Dial” to set the display mode to dial display mode as shown in the figure below. This mode displays the voltage, current and power of the currently selected channel in both number and dial formats and you can directly view the values and variations of the voltage, current and power of the channel currently selected. In this mode, you can set the voltage and current of the channel currently selected using the numeric keyboard or knob.
RIGOL User Interface 8 9 10 11 1 2 3 4 5 6 7 Figure 8 DP831A User Interface Table 1 2 3 4 5 6 7 8 9 10 11 2 DP831A User Interface Explanation Voltage and current setting values Overvoltage and overcurrent protection setting values Actual output voltage Actual output current Actual output power Channel output mode Menu bar Channel number Channel output status Channel currently selected Status bar, display the system status indicators. : over-temperature protection is enabled.
RIGOL To Use the Built-in Help System The built-in help system provides help information for any front panel key (except the parameter input area) and menu keys for users to quickly obtain the function prompts of the function keys or menus. Obtain the help information of any key Press Help to illuminate it and press the desired key to get the corresponding help information; at the same time, the backlight of Help goes off. Press exit the help system.
RIGOL Troubleshooting The commonly encountered failures and their solutions are listed below. When you encounter those problems, please solve them following the corresponding steps. If the problem remains still, please contact RIGOL and provide your device information (Utility SysInfo). 1. The instrument can not start up. (1) Check whether the power is correctly connected. (2) Check whether the power switch at the front panel is really on.
