User Manual

ManualsBrandsRigol ManualsLaboratory EquipmentRigol DS1202Z-E Digital 200 MHz 2-channel 1 GS/s 24000 KP 8 Bit

131

132

133

134

135

136

137

138

139

140

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Notices and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- Care and Cleaning
- Environmental Considerations
DS1000Z-E Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Parameter Setting Method
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Waveform Invert
- Vertical Scale
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sin(x)/x
- Sample Rate
- Memory Depth
- Anti-aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurement
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Protocol Decoding
- Parallel Decoding
- RS232 Decoding
- I2C Decoding
- SPI Decoding
Chapter 8 Reference Waveform
- To Enable REF Function
- To Select REF Source
- To Adjust REF Waveform Display
- To Save to Internal Memory
- To Set the Color
- To Reset the Reference Waveform
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 9 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- Test and Output
- To Save the Test Mask
- To Load the Test Mask
Chapter 10 Waveform Record
- Common Settings
- Playback Option
- Record Option
Chapter 11 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
Chapter 12 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 13 Accessibility Setting
- Remote Interface Configuration
  - LAN Configuration
  - USB Device
- System-related
Chapter 14 Remote Control
- Remote Control via USB
- Remote Control via LAN
Chapter 15 Troubleshooting
Chapter 16 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL Chapter 6 MATH and Measurement

6-28 DS1000Z-E User Guide

Voltage Parameters

Figure 6-5 Voltage Parameters

1. Vmax: the voltage value from the highest point of the waveform to the GND.

2. Vmin: the voltage value from the lowest point of the waveform to the GND.

3. Vpp: the voltage value from the highest point to the lowest point of the

waveform.

4. Vtop: the voltage value from the flat top of the waveform to the GND.

5. Vbase: the voltage value from the flat base of the waveform to the GND.

6. Vamp: the voltage value from the top of the waveform to the base of the

waveform.

7. Vupper: the actual voltage value corresponding to the threshold maximum

value.

8. Vmid: the actual voltage value corresponding to the threshold middle value.

9. Vlower: the actual voltage value corresponding to the threshold minimum

value.

10. Vavg: the arithmetic average value on the whole waveform or on the gating

area. The calculation formula is as follows:

Average=



(6-2)

Wherein,

is the measurement result of the

th point,

is the number of

points being measured.

11. Vrms: the root mean square value on the whole waveform or the gating area.

The calculation formula is as follows.

Preshoot

Overshoot

Vamp

Vbase

Vmax

Vmin

Vpp

Vtop

Vupper

Vmid

Vlower