User Manual

ManualsBrandsRigol ManualsLaboratory EquipmentRigol DS1202Z-E Digital 200 MHz 2-channel 1 GS/s 24000 KP 8 Bit

181

182

183

184

185

186

187

188

189

190

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Notices and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- Care and Cleaning
- Environmental Considerations
DS1000Z-E Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Parameter Setting Method
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Waveform Invert
- Vertical Scale
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sin(x)/x
- Sample Rate
- Memory Depth
- Anti-aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurement
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Protocol Decoding
- Parallel Decoding
- RS232 Decoding
- I2C Decoding
- SPI Decoding
Chapter 8 Reference Waveform
- To Enable REF Function
- To Select REF Source
- To Adjust REF Waveform Display
- To Save to Internal Memory
- To Set the Color
- To Reset the Reference Waveform
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 9 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- Test and Output
- To Save the Test Mask
- To Load the Test Mask
Chapter 10 Waveform Record
- Common Settings
- Playback Option
- Record Option
Chapter 11 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
Chapter 12 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 13 Accessibility Setting
- Remote Interface Configuration
  - LAN Configuration
  - USB Device
- System-related
Chapter 14 Remote Control
- Remote Control via USB
- Remote Control via LAN
Chapter 15 Troubleshooting
Chapter 16 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

Chapter 11 Display Control RIGOL

DS1000Z-E User Guide 11-3

3. Infinite

In this mode, the oscilloscope displays the waveform newly acquired without

clearing the waveforms acquired formerly. The waveforms acquired formerly will

be displayed in relatively low-brightness color and the waveform newly acquired

will be displayed in normal brightness and color. Infinite persistence can be used

to measure noise and jitter and to capture incidental events.

To Set the Waveform Intensity

Press Display  Intensity or turn in non-menu operation to adjust the

waveform brightness of the channel. The default is 60% and the range available is

from 0% to 100%.

To Set the Screen Grid

Press Display  Grid to set the screen grid type.

 : turn the background grid and coordinate on.

 : turn the background grid off.

 : turn the background grid and coordinate off.

To Set the Grid Brightness

Press Display  Brightness to set the brightness of the screen grid. Turn to

adjust the grid brightness. The default is 50% and the range available is from 0% to

100%.