User Manual

ManualsBrandsRigol ManualsLaboratory EquipmentRigol DS1202Z-E Digital 200 MHz 2-channel 1 GS/s 24000 KP 8 Bit

201

202

203

204

205

206

207

208

209

210

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Notices and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- Care and Cleaning
- Environmental Considerations
DS1000Z-E Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Parameter Setting Method
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Waveform Invert
- Vertical Scale
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sin(x)/x
- Sample Rate
- Memory Depth
- Anti-aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurement
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Protocol Decoding
- Parallel Decoding
- RS232 Decoding
- I2C Decoding
- SPI Decoding
Chapter 8 Reference Waveform
- To Enable REF Function
- To Select REF Source
- To Adjust REF Waveform Display
- To Save to Internal Memory
- To Set the Color
- To Reset the Reference Waveform
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 9 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- Test and Output
- To Save the Test Mask
- To Load the Test Mask
Chapter 10 Waveform Record
- Common Settings
- Playback Option
- Record Option
Chapter 11 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
Chapter 12 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 13 Accessibility Setting
- Remote Interface Configuration
  - LAN Configuration
  - USB Device
- System-related
Chapter 14 Remote Control
- Remote Control via USB
- Remote Control via LAN
Chapter 15 Troubleshooting
Chapter 16 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL Chapter 13 Accessibility Setting

13-2 DS1000Z-E User Guide

Remote Interface Configuration

DS1000Z-E provides two remote control interfaces: USB Device (TMC and SICD static

image capture devices share this interface) and LAN. The USB Device interface takes

precedence over the LAN interface. You can press Utility  IO Setting 

RemoteIO to select the desired communication interface according to the particular

condition.

 When the USB Device interface is connected and press Utility  IO Setting 

USB Device  "Computer", the system will select the USB Device interface

automatically as the only valid interface no matter whether the LAN interface is

connected or not. In the RemoteIO menu, the state of the TMC (USB Device) is

"ON", and the state of the LAN is "OFF". The states of the interfaces are not

allowed to be changed.

 When only the LAN interface is connected, the system will automatically detect

the LAN interface. In the RemoteIO menu, the state of the LAN is "ON" by

default, and you can press LAN softkey to turn "OFF" or "ON" the LAN interface.

The state of the TMC (USB Device) is "OFF", and it is not allowed to make any

change.

LAN Configuration

Press Utility  IO Setting  LAN Conf. to turn on the LAN setting interface. You

can view the network connection status and configure the network parameters.

Figure 13-1 LAN Setting Interface

Network Status

Current IP

Config Type

MAC Address

VISA Address

IP Config Type

Status