User Manual

ManualsBrandsRigol ManualsLaboratory EquipmentRigol DS1202Z-E Digital 200 MHz 2-channel 1 GS/s 24000 KP 8 Bit

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Notices and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- Care and Cleaning
- Environmental Considerations
DS1000Z-E Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Parameter Setting Method
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Waveform Invert
- Vertical Scale
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sin(x)/x
- Sample Rate
- Memory Depth
- Anti-aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurement
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Protocol Decoding
- Parallel Decoding
- RS232 Decoding
- I2C Decoding
- SPI Decoding
Chapter 8 Reference Waveform
- To Enable REF Function
- To Select REF Source
- To Adjust REF Waveform Display
- To Save to Internal Memory
- To Set the Color
- To Reset the Reference Waveform
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 9 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- Test and Output
- To Save the Test Mask
- To Load the Test Mask
Chapter 10 Waveform Record
- Common Settings
- Playback Option
- Record Option
Chapter 11 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
Chapter 12 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 13 Accessibility Setting
- Remote Interface Configuration
  - LAN Configuration
  - USB Device
- System-related
Chapter 14 Remote Control
- Remote Control via USB
- Remote Control via LAN
Chapter 15 Troubleshooting
Chapter 16 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL

DS1000Z-E User Guide V

Measurement Category

DS1000Z-E series digital oscilloscopes can make measurements in Measurement

Category I.

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Measurement Category Definitions

Measurement category I is for measurements performed on circuits not directly

connected to MAINS. Examples are measurements on circuits not derived from

MAINS, and specially protected (internal) MAINS derived circuits. In the latter case,

transient stresses are variable. For that reason, the transient withstand capability of

the equipment is made known to the user.

Measurement category II is for measurements performed on circuits directly

connected to low voltage installations. Examples are measurements on household

appliances, portable tools and similar equipment.

Measurement category III is for measurements performed in building installations.

Examples are measurements on distribution boards, circuit-breakers, wiring

(including cables, bus-bars, junction boxes, switches and socket-outlets) in fixed

installations, equipment for industrial use and some other equipment. For example,

stationary motors with permanent connection to a fixed installation.

Measurement category IV is for measurements performed at the source of a

low-voltage installation. Examples are electricity meters and measurements on

primary overcurrent protection devices and ripple control units.