User Manual

ManualsBrandsRigol ManualsLaboratory EquipmentRigol DS1202Z-E Digital 200 MHz 2-channel 1 GS/s 24000 KP 8 Bit

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Notices and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- Care and Cleaning
- Environmental Considerations
DS1000Z-E Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Parameter Setting Method
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Waveform Invert
- Vertical Scale
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sin(x)/x
- Sample Rate
- Memory Depth
- Anti-aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurement
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Protocol Decoding
- Parallel Decoding
- RS232 Decoding
- I2C Decoding
- SPI Decoding
Chapter 8 Reference Waveform
- To Enable REF Function
- To Select REF Source
- To Adjust REF Waveform Display
- To Save to Internal Memory
- To Set the Color
- To Reset the Reference Waveform
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 9 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- Test and Output
- To Save the Test Mask
- To Load the Test Mask
Chapter 10 Waveform Record
- Common Settings
- Playback Option
- Record Option
Chapter 11 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
Chapter 12 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 13 Accessibility Setting
- Remote Interface Configuration
  - LAN Configuration
  - USB Device
- System-related
Chapter 14 Remote Control
- Remote Control via USB
- Remote Control via LAN
Chapter 15 Troubleshooting
Chapter 16 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL Chapter 5 To Trigger the Oscilloscope

5-12 DS1000Z-E User Guide

(a) (b)

Figure 5-5 Trigger Level Information Display

Note: Under the "Slope" trigger menu, you can also press down the trigger level

knob continuously to switch the vertical window.

During the adjustment of trigger level, two orange trigger level lines and two trigger

marks ( and ) appear on the screen and move up and down with the rotation

of the knob. At the same time, the current trigger level information is displayed at the

lower right corner of the screen according to different slope condition settings. After

stopping turning the knob, the trigger level lines and trigger level information

disappear in about 2 s.

Trigger Mode:

Press Sweep to open the trigger mode list and select auto, normal or single. For the

details, please refer to "Trigger Mode". The corresponding status light of the

current trigger mode turns on.

Trigger Setting:

Press Setting to set the trigger parameters (trigger holdoff and noise rejection)

under this trigger type.