User Guide

ManualsBrandsRIGOL ManualsDigital OscilloscopesDigital Oscilloscope

251

252

253

254

255

256

257

258

259

260

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Terms and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- General Care and Cleaning
- Environmental Considerations
DS2000 Series Overview
Document Overview
1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
2 To Set the Vertical System
- To Enable the Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Waveform Invert
- Vertical Scale
- Vertical Expansion
- Amplitude Unit
- Channel Label
- Delay Calibration
3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
- Horizontal Scale
- Horizontal Reference
4 To Set the Sample System
- Acquisition Mode
- Sample Mode
- Sample Rate
- Memory Depth
- Antialiasing
5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
6 To Make Measurements
- Math Operation
- Auto Measurement
- Cursor Measurement
7 Protocol Decoding
- Parallel Decoding
- RS232 Decoding (Option)
- I2C Decoding (Option)
- SPI Decoding (Option)
8 Reference Waveform
- To Enable REF Function
- To Set the Color
- To Select REF Source
- To Save to Internal Memory
- To Adjust REF Waveform Display
- To Export to Internal or External Memory
- To Import from Internal or External Memory
9 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- Test and Ouput
- To Save the Test Mask
- To Load the Test Mask
10 Waveform Record
- Waveform Record
- Record Constant On
- Waveform Playback
- Waveform Analysis
  - Analysis Based on Trace
  - Analysis Based on Pass/Fail Mask
11 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
- To Set the Menu Display
12 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
13 System Function Setting
- Remote Interface Configuration
- System-related
14 Remote Control
- Remote Control via USB
- Remote Control via LAN
- Remote Control via GPIB
15 Troubleshooting
16 Specifications
17 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
- Appendix C: Any Question or Comment?
Index

16 Specifications RIGOL

DS2000 User’s Guide

16-5

Data Type H, L

Setup Time 2 ns to 1 s

Hold Time 2 ns to 1 s

RS232/UART Trigger

Polarity Negative, Positive

Trigger Condition Start, Error, Check Error, Data

Baud Rate 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600

bps, 115200 bps, User

Data Bits 5 bit, 6 bit, 7 bit, 8 bit

I2C Trigger

Trigger Condition Start, Restart, Stop, Missing ACK, Address, Data, A&D

Address Bits 7 bit, 10 bit

Address Range 0 to 127, 0 to 1023

Byte Length 1 to 5

SPI Trigger

Trigger Condition Timeout

Timeout Value 100 ns to 1 s

Data Bits 4 bit to 32 bit

Data Line Setting H, L, X

USB Trigger

Signal Speed Low Speed, Full Speed

Trigger condition SOP, EOP, RC, Suspend, Exit Suspend

Measure

Cursor

Manual Mode

Voltage Deviation between Cursors (

△

Time Deviation between Cursors (

△

Reciprocal of

△

T (Hz) (1/

△

Track Mode Voltage and Time Values of the Waveform

Point

Auto Mode Allow to display cursors during auto

measurement

Auto Measurement

Measurements of Maximum, Minimum, Peak-Peak Value, Top

Value, Bottom Value, Amplitude, Average, Mean Square

Root, Overshoot, Pre-shoot, Frequency, Period, Rise Time,