Information

ManualsBrandsRIGOL ManualsLaboratory Test EquipmentDSA705Spectrum Analyser, Frequency Fange ,Bandwidth (RBW) 100 Hz - 1 MHz

Chapter 5 Specifications RIGOL

User’s Guide for DSA700 Series

5-1

Chapter 5 Specifications

Specifications are valid under the following conditions: the instrument is within the

calibration period, is stored for at least two hours at 0℃ to 50℃ temperature and

is warmed up for 40 minutes. Unless otherwise noted, the specifications in the

manual include the measurement uncertainty.

Typical (typ.): characteristic performance, which 80 percent of the measurement

results will meet at room temperature (approximately 25℃). This data is not

warranted and does not include the measurement uncertainty.

Nominal (nom.): the expected mean or average performance or a designed

attribute (such as the 50Ω connector). This data is not warranted and is measured

at room temperature (approximately 25℃).

Measured (meas.): an attribute measured during the design phase which can be

compared to the expected performance, such as the amplitude drift variation with

time. This data is not warranted and is measured at room temperature

(approximately 25℃).

Note: All charts in this manual are the measurement results of multiple instruments at room

temperature unless otherwise noted.

Summary of content (10 pages)

PAGE 1
Chapter 5 Specifications RIGOL Chapter 5 Specifications Specifications are valid under the following conditions: the instrument is within the calibration period, is stored for at least two hours at 0℃ to 50℃ temperature and is warmed up for 40 minutes. Unless otherwise noted, the specifications in the manual include the measurement uncertainty. Typical (typ.): characteristic performance, which 80 percent of the measurement results will meet at room temperature (approximately 25℃).
PAGE 2
RIGOL Chapter 5 Specifications Technical Specifications Frequency Frequency DSA705 DSA710 Frequency range 100 kHz to 500 MHz 100 kHz to 1 GHz Frequency resolution 1 Hz Internal Reference Frequency DSA705 Reference frequency Accuracy Initial calibration accuracy Temperature stability Aging rate DSA710 10 MHz ±[ (time since last calibration × aging rate) + temperature stability + calibration accuracy] <1 ppm 0℃ to 50℃, reference to 25℃ <2 ppm <2 ppm/year Frequency Readout Accuracy Marker resolutio
PAGE 3
RIGOL Chapter 5 Specifications SSB Phase Noise Carrier offset DSA705 DSA710 20℃ to 30℃, fc = 500 MHz 20℃ to 30℃, fc = 1 GHz 10 kHz <-80 dBc/Hz 100 kHz <-100 dBc/Hz (typ.) Residual FM 20℃ to 30℃, RBW = VBW = 1 kHz DSA705 Residual FM DSA710 <50 Hz (nom.) Bandwidths Set "Auto SWT" to "Accy" DSA705 DSA710 Resolution bandwidth (-3 dB) 100 Hz to 1 MHz, in 1-3-10 sequence RBW uncertainty <5% (nom.
PAGE 4
RIGOL Chapter 5 Specifications Displayed Average Noise Level (DANL) DSA705 Frequency PA off PA on DSA710 attenuation = 0 dB, RBW = VBW = 100 Hz, sample detector, trace average ≥ 50, 20℃ to 30℃, input impendence = 50 Ω 100 kHz to 1 MHz <-90 dBm, <-110 dBm (typ.) 1 MHz to 500 MHz <-100 dBm, <-110 dBm (typ.) 500 MHz to 1 GHz 100 kHz to 1 MHz <-110 dBm, <-130 dBm (typ.) 1 MHz to 500 MHz <-120 dBm, <-130 dBm (typ.) 500 MHz to 1 GHz <-90 dBm, <-110 dBm (typ.) <-100 dBm, <-110 dBm (typ.
PAGE 5
RIGOL Chapter 5 Specifications Absolute Amplitude Uncertainty DSA705 DSA710 fc = 50 MHz, peak detector, preamplifier off, attenuation = 10 dB, input signal level = -10dBm, 20℃ to 30℃ Uncertainty <0.4 dB RBW Switching Uncertainty relative to 1 kHz RBW Uncertainty <0.1 dB Reference Level Range Resolution -100 dBm to +20 dBm, in 1 dB step log scale 0.01 dB linear scale 4 digits Preamplifier DSA705 (standard) Gain 100 kHz to 500 MHz 20 dB (nom.) 500 MHz to 1 GHz DSA710 (standard) 20 dB (nom.
PAGE 6
RIGOL Chapter 5 Specifications Distortion Second Harmonic Intercept DSA705 Second harmonic intercept (SHI) DSA710 fc ≥ 50 MHz, input signal level = -20 dBm, attenuation = 10 dB +40 dBm Third-order Intercept DSA705 Third-order intercept (TOI) DSA710 fc ≥ 50 MHz, two -20 dBm tones at input mixer spaced by 200 kHz, attenuation = 10 dB +10 dBm 1dB Gain Compression 1dB compression of input mixer (P1dB) fc ≥ 50 MHz, attenuation = 0 dB >0 dBm Spurious Response DSA705 Spurious response, inherent DSA710
PAGE 7
RIGOL Chapter 5 Specifications Sweep Sweep Sweep time Sweep time uncertainty DSA705 DSA710 span ≥ 100 Hz 10 ms to 500 s 10 ms to 1000 s zero span 20 μs to 500 s 20 μs to 1000 s span ≥ 100 Hz 5% (nom.) zero span (sweep time setting value > 1 ms) Sweep mode 5% (nom.) continuous, single Trigger Trigger Trigger source free run, video, external External trigger level 5 V TTL level SSC-DSA (Option) Signal Seamless Capture (SSC) Measurement bandwidth User’s Guide for DSA700 Series 1.
PAGE 8
RIGOL Chapter 5 Specifications Input /Output Front Panel Connectors RF input impedance 50 Ω (nom.) connector N female Internal/ External Reference Internal reference External reference frequency 10 MHz output level +3 dBm to +10 dBm, +8 dBm (typ.) impedance 50 Ω (nom.) connector BNC female frequency 10 MHz ± 5 ppm input level 0 dBm to +10 dBm impedance 50 Ω (nom.) connector BNC female External Trigger Input External trigger input impedance 1 kΩ (nom.
PAGE 9
RIGOL Chapter 5 Specifications General Specifications Display Type TFT LCD Resolution 800 x 480 pixels Size 8 inch Colors 64k Printer Supported Protocol PictBridge Mass Memory flash disk (internal), Mass memory USB storage device (not supplied) Power Supply Input voltage range, AC 100 V to 240 V (nom.) AC supply frequency 45 Hz to 440 Hz Power consumption 35 W (typ.), max.
PAGE 10
RIGOL Chapter 5 Specifications Electromagnetic Compatibility and Safety in line with EN61326-1:2006 IEC 61000-4-2:2001 IEC 61000-4-3:2002 IEC 61000-4-4:2004 EMC IEC 61000-4-5:2001 IEC 61000-4-6:2003 ±4.0 kV (contact discharge), ±4.0 kV (air discharge) 3 V/m (80 MHz to 1 GHz), 3 V/m (1.4 GHz to 2 GHz), 1 V/m (2.0 GHz to 2.7 GHz) 1 kV power lines 0.5 kV (phase to neutral), 0.5 kV (phase to PE), 1 kV (neutral to PE) 3 V, 0.