Datasheet

20
RIGOL
Trigger Type
Trigger Type
Zone Trigger
Trigger in the rectangle area drawn manually, supporting trigger zone A and trigger zone B. The trigger
conditions can be "Intersect" or "Not intersect"
Source channel: CH1~CH4; only one analog channel is triggered each time
Trigger Type
Standard: Edge trigger, Pulse trigger, Slope trigger, Video trigger, Pattern trigger, Duration trigger, Timeout
trigger, Runt trigger, Window trigger, Delay trigger, Setup/Hold trigger, and Nth Edge trigger
Option: RS232, UART, I2C, SPI, CAN, FlexRay, LIN, I2S, and MIL-STD-1553
Edge
Trigger on the threshold of the specified edge of the input signal. The edge types can be Rising, Falling, or
Either.
Source channel: CH1~CH4, D0~D15, or AC Line
Pulse
Trigger on the positive or negative pulse with a specified width. The pulse width is greater or smaller than a
certain value or within a certain time range.
Source channel: CH1~CH4, D0~D15
Slope
Trigger on the positive or negative slope of the specified time (800 ps~10 s). The slew time is greater or
smaller than a certain value or within a certain time range.
Source channel: CH1~CH4
Video
Trigger on all lines, specified line, add field, or even field that conforms to the video standards. The supported
video standards include NTSC, PAL/SECAM, 480P, and 576P.
Source channel: CH1~CH4
Pattern
Identifies a trigger condition by searching for a specified pattern. The pattern is a combination of multiple
selected channel sources. The logic pattern of each channel is H, L, X, Rising, or Falling.
Source channel: CH1~CH4, D0~D15
Duration
Trigger when the specified pattern meets the specified duration condition. The pattern is a combination of
multiple selected channel sources. The logic pattern of each channel is H, L, X. The duration is greater or
smaller than a certain value, or within a certain time range, or outside a certain time range.
Source channel: CH1~CH4, D0~D15
Timeout
Trigger when duration of a certain event exceeds the specified time (16 ns~10 s). The event can be specified
as Rising, Falling, or Either.
Source channel: CH1~CH4, D0~D15
Runt
Trigger when the pulses pass through one threshold but fail to pass through another threshold. The channel
only supports analog channels
Source channel: CH1~CH4
Window
Trigger in a specified window state when the rising edge of the signal crosses the upper threshold or the falling
edge crosses the lower threshold. The window state can be Enter, Exit, or Time.
Source channel: CH1~CH4
Delay
Trigger when the time difference between the specified edges of Source A and Source B meets the preset
time. The duration is greater or smaller than a certain value, or within a certain time range, or outside a certain
time range.
Source channel: CH1~CH4, D0~D15
Setup/Hold
When the setup time or hold time between the input clock signal and the data signal is smaller than the
specified time (8 ns~1 s).
Source channel: CH1~CH4, D0~D15
Nth Edge
Trigger on the Nth edge that appears after the specified idle time. The edge can be specified as Rising or
Falling.
Source channel: CH1~CH4, D0~D15
RS232/UART (Option)
MSO5000-COMP option
Trigger on the Start, Error, Check Error, or Data frame of the RS232/UART bus (up to 20 Mb/s).
Source channel: CH1~CH4, D0~D15
I2C (Option)
MSO5000-EMBD option
Trigger on the Start, Stop, Restart, MissedACK, Address (7 bits, 8 bits, or 10 bits), Data, or Address Data of the
I2C bus.
Source channel: CH1~CH4, D0~D15
SPI (Option)
MSO5000-EMBD option
Trigger on the specified pattern of the specified data width (4~32) of SPI bus. CS and Timeout are supported.
Source channel: CH1~CH4, D0~D15
CAN (Option)
MSO5000-AUTO option
Trigger on the start of a frame, end of a frame, Remote ID, Overload, Frame ID, Frame Data, Data&ID, Frame
Error, Answer Error, Check Error, Format Error, and Random of the CAN signal (up to 5Mb/s). The supported
CAN bus signal types include CAN_H, CAN_L, TX/RX, and DIFF.
Source channel: CH1~CH4, D0~D15
FlexRay (Option)
MSO5000-FLEX option
Trigger on the specified position (TSS End, FSS_BSS End, FES End, DTS End), frame (Invalid, Syn, Start, All),
symbol (CAS/MTS and WUS), error (Head CRC Err, Tail CRC Err, Decode Err, and Random Err.) of the FlexRay
signal (up to 10 Mb/s).
Source channel: CH1~CH4, D0~D15
LIN (Option)
MSO5000-AUTO option
Trigger on the Sync, ID, Data (length settable), Data&ID, Wakeup, Sleep, and Error of the LIN bus signal (up to
20 Mb/s).
Source channel: CH1~CH4, D0~D15
I2S (Option)
MSO5000-AUDIO option
Trigger on 2's complement data of audio left channel, right channel, or either channel (＝, ≠, ＞, ＜, ＜＞, ＞
＜). The available alignment modes include I2S, LJ, and RJ.
Source channel: CH1~CH4, D0~D15 (only available for the MSO5XX4 model or the model installed with the
MSO5000-4CH option)