0” Woodworking Bandsaw Owner’s Manual Model: 10-300 Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: For more information: www.rikontools.com or info@rikontools.com For Parts or Questions: techsupport@rikontools.
TABLE OF CONTENTS Safety Instructions...............................................................................................................................................3-4 Carton Contents.....................................................................................................................................................5 Hardware Package Contents.................................................................................................................................
SAFETY INSTRUCTIONS General Safety Warnings KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications, work capabilities, and its Always Ground All Tools. If your tool is equipped with a three-pronged plug, you must plug it into a three-hole electric receptacle. If you use an adapter to accommodate a two-pronged receptacle, you must attach the adapter plug to a known ground. Never remove the third prong of the plug. Always Avoid Dangerous Environments.
Never Overreach. Keep your proper footing and balance at all times. Never Stand on Tools. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Always Disconnect Tools. Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters. Always Avoid Accidental Staring. Make sure switch is in “OFF” position before plugging in cord. Never Leave Tools Running Unattended. Always Check for Damaged Parts.
CARTON CONTENTS CARTON CONTENTS The model 10-300 10” Bandsaw is shipped complete in one box. Item A B C D E Unpacking and Checking Contents a. Separate all parts from carton and check each item with “Table of Carton Contents” to make sure all items are accounted for, before discarding any packing material. Description Q’ty. Main Machine..................................................................1 Table.......................................................................... .................
ASSEMBLY Initial Assembly The machine is supplied partly assembled. Prior to use, the following items have to be installed: bandsaw table, star knob (blade tensioning) and rip fence. WARNING: To avoid injury, do not attempt to run or use this machine until all parts are assembled and working properly. Installing the Table a. Place table on to the upper table trunnion, taking care when passing the saw blade through the slot in the table (See Fig. 1).
Mounting the Bandsaw For maximun stability during use, it is strongly recommended that the bandsaw be mounted on a sturdy bench or worktable. It should be bolted down utilizing the 1/4” holes in the bandsaw base plate. (See Fig. 6) Dust Collection The bandsaw has a 2-1/2” dust extraction port (See Fig. 7) included. It is recommended that when in use, the bandsaw is connected to a suitable dust collector. Fig.
Installing/Changing and Setting the Saw Blade Cont. h. Replace leveling wing nut and screw to table. i. Close and lock both bandsaw wheel doors before reconnecting the power supply. Wing Nut Tracking Knob Tracking the Bandsaw Blade Set the tracking of the blade before setting the blade guides. Once the blade is installed and tensioned, track the blade by adjusting the tracking knob by hand (See Fig. 10). The blade should run in the center of the bandsaw wheel as shown in (See fig. 9).
OPERATION 1. The blade cuts on a continuous down-stroke. 2. Check all the necessary settings and adjustments, and ensure that all the recommended safety procedures are in place. 3. Start the bandsaw by placing the switch towards the ‘on’ position. 4. Wait for the saw to come to full speed before starting to cut. Never start the saw with the workpiece in contact with the saw blade. Fig.15 5. Slowly feed the workpiece towards the blade, putting only light pressure on it. 6.
MAINTENANCE WARNING: To avoid injury due to unexpected starting, before cleaning or carring out maintenance work, switch off and disconnect the bandsaw from the power source. Changing Drive Belt 1. Release saw blade tension by turning star knob on the top of upper bandsaw cabinet counter-clockwise. Never use water or other liquids to clean the bandsaw. Use a dry brush. 2. Using a 6mm hexagonal wrench to release socket head cap screw on motor mounting flange. (See Fig.
TROUBLE SHOOTING Problem Diagnosis Remedy The machine does not work when switched on. 1. No power supply. 2. Defective switch. 1. Check the cable for breakage. 2. Check the fuse or breaker. 3. Contact you local dealer for repair parts. The blade does not move with the motor running. 1. The blade tension knob has not been tightened. 2. The blade has come off one of the wheels. 3. The saw blade has broken. 4. The drive belt has snapped. 1. Switch off the motor, tighten the blade tension knob. 2.
Eletrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided.
Parts List Key No.
Parts Explosion 14
Notes 15
Warranty 2-Year Limited Warranty RIKON Power Tools/Richen Enterprise, Inc. (“Seller”) warrants to only the original retail consumer/ purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail. This warranty may not be transferred.
For more information: 400 West Cummings Park, Suite 1000 Woburn, MA 01801 877-884-5167/781-933-8400 techsupport@rikontools.com www.rikontools.com Copyright Richen Enterprise, Inc.
