6” X 48”Belt & 10”Disc Sander Owner’s Manual Model: 50-120 Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: For more information: www.rikontools.com or info@rikontools.com For Parts or Questions: Part # 50-120M2 techsupport@rikontools.
Operator Safety: Required Reading IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. There are certain applications for which this tool was designed. We strongly recommend that this tool not be modified and/or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.
ALWAYS DISCONNECT TOOLS. Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters. ALWAYS AVOID ACCIDENTAL STARTING. Make sure switch is in “OFF” position before plugging in cord. NEVER LEAVE TOOLS RUNNING UNATTENDED. ALWAYS CHECK FOR DAMAGED PARTS. Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure that it will operate properly and perform its intended function.
Table of Contents Safety Warnings..................................................................................................................................2-3 Sander Safety Rules ..........................................................................................................................3 Specifications ........................................................................................................................................4 Contents of Package ............................
Contents of Package When unpacking, check to make sure the following parts are included. If any parts are missing or broken, please call RIKON Power Tools at the number on the cover of this manual as soon as possible.
Assembly Securing Sander Base Assembly to Workbench The sander base must be secured before using. Attach a large C-Clamp to each side of the sander and the workbench. Or, permanently mount following the instructions below: 1. Place the sander on the workbench in its final operating location. 2. Place a pencil through the mountong holes of the sander base (42) and mark the hole locations on workbench. Fig. 01 3. Remove sander and drill four 3/8 inch holes through the workbench. 4.
Installing the Disc Table Assembly Warning: To avoid jamming the workpiece or fingers between the table and sanding surface, the table edge should be a maximum of 1/16 in from sanding surface. 1. Use two M6x16 pan head screws to fasten the table support mount to the front of sander. 2. Place the support table w/scale onto the table support mount. Fig. 04 3. Put a 6mm flat washer on the table lock knob, and place the knob into the tilt scale plate and mount. Hand tighten it only at this time. (See Fig.
Installing the Sanding Belt Warning: To avoid injury from accidental start, make sure tool is unplugged before making any adjustments. On the under side of the sanding belt, you will find a “direction arrow”. The sanding belt must run in the direction of this arrow so that the splice does not come apart. Fig. 08 1. Slide tension lever to the right to release the belt tension. (See Fig. 08) 2. Place the sanding belt over the drums with the direction arrow pointing in the proper direction. (See Fig.
Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided.
Operation Bevel Sanding The work table can be tilted from 0 to 45 degrees for bevel sanding. Loosen the table lock knob and tilt the worktable to desired angle as shown. (See Fig. 12) Retighten table lock knob. Warning: To avoid jamming the workpiece or fingers between the table and sanding surface, the table should repositioned on the table support to retain a maximum of 1/16” distance between sanding surface and table. Fig.
End Sanding on the Sanding Belt To sand the end of a long workpiece, it is recommended to sand with the belt in the vertical position. 1. To raise the belt to the vertical position, follow the instructions in “Positioning Belt Bed” on the previous page. 2. Install the worktable assembly. 3. Move the work evenly across the sanding belt. (See Fig. 16) Fig. 16 Sanding Curved Edges Always sand inside curves on the idler drum as shown.(See Fig.
Maintenance Warning: For your safety, remove the plug from power source outlet before adjusting, maintaining, of lubricating your belt and disc sander. 1. Apply a light coat of paste wax to the worktable to make feeding stock easier, and reduce rust. 2. Use compressed air to frequently blow out dust and debris from sander and motor. (See Fig. 20) Warning: To avoid electrocution or fire, any repairs to electrical systems should be done only by qualified service technicians.
Troubleshooting SYMPTOM PROBABLE CAUSE REMEDY Sander does not operate 1. Not plugged into wall outlet. 2. Locking key is not inserted. 3. Power switch defective. 4. Motor or wiring problem. 1. Plug into wall outlet. 2. Insert locking key. 3. Replace power switch. 4. Take to a qualified technician. Motor slows when sanding 1. Timing belt is too tight. 2. Applying too much pressure on work piece. 1. Decrease tension. 2. Apply less pressure to work piece when sanding. Sanding Belt runs off drums 1.
Parts List Key No. 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 Key No. Description Part No.
Parts Explosion 15
Notes 16
Warranty 2-Year Limited Warranty RIKON Power Tools/Richen Enterprise, Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail. This warranty may not be transferred.
For more information: 110 Cummings Park Woburn, MA 01801 877-884-5167/781-933-8400 techsupport@rikontools.com www.rikontools.com Copyright Richen Enterprise, Inc.
