2” x 16” Mini Lathe Owner’s Manual Model: 70-050 Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: For more information: www.rikontools.com or info@rikontools.com For Parts or Questions: Part # 70-050M1 techsupport@rikontools.
Safety Warning IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. 7KHUH DUH FHUWDLQ DSSOLFDWLRQV IRU ZKLFK WKLV WRRO ZDV GHVLJQHG :H VWURQJO\ UHFRPPHQG WKDW WKLV WRRO QRW EH PRGL¿HG DQG or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.
ALWAYS DISCONNECT TOOLS. ALWAYS DISCONNECT TOOLS.and when changing accessories such as blades, bits, and cutters. Disconnect tools before servicing Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters. ALWAYS AVOID ACCIDENTAL STARTING. ALWAYS STARTING. Make sureAVOID switch ACCIDENTAL is in “OFF” position before plugging in cord. Make sure switch is in “OFF” position before plugging in cord. NEVER LEAVE TOOLS RUNNING UNATTENDED.
Table of Contents Safety Warnings.....................................................................................................................................................2 Lathe Safety Rules................................................................................................................................ ............... 3 Specifications.....................................................................................................................................................
Contents of Package Unpacking and Checking Contents Unpack your lathe from its carton and check to see that you have all of the following items. Do not turn your machine ON if any of these items are missing. You may cause injury to yourself or damage to your machine. Item Description Q'ty A Lathe 1 B Wrench 1 C Knockout Bar 1 D Knockout Bar for Live Center Point 1 E Manual 1 For more information: For Parts or Questions: www.rikontools.com or info@rikontools.
Getting to Know Your Lathe 1 2 3 4 6 5 7 8 11 10 9 Item Description Item 1 2 3 4 5 6 7 Handwheel Headstock Face plate Spur center Tool rest Live center Tailstock 8 9 10 11 12 13 14 12 13 14 Description Tailstock handwheel Switch Tool rest seat locking lever Tailstock locking lever Tailstock spindle locking arm Tool rest base Motor Assembly The machine must not be plugged in and the power switch must be in the OFF position until assembly is complete.
Attaching Spur Center On the Headstock Insert spur center, with a No.2 Morse Tapper shank, into the headstock spindle. (See Fig.02) Fig.02 Knockout Bar The knockout bar is used to remove the spur center from the headstock spindle. Insert knockout bar into hole at opposite side from spur center. (See Fig.04) Fig.03 Tailstock spindle Attaching Live Center On the Tailstock Live center Insert the live center, with a No. 2 Morse Taper shank into the tailstock spindle. (See Fig.04) Fig.
Adjustments and Operations Tool rest Adjusting the Tool Rest The tool rest base can be easily moved along the lathe bed. Loosen locking lever counter clockwise, slide tool rest base to new position, and tighten locking lever clockwise. To adjust the height of the tool rest, loosen locking arm, raise or lower tool rest, tighten locking arm. (See Fig.07) Tool rest base Locking arm Locking lever Fig.07 Note: Position the tool rest as close to the work piece as possible.
Changing Spindle Speeds The lathe features a six step motor and spindle pulleys to provide different spindle speeds. The lathe Model#70-050VS features a three step motor and spindle pulleys to provide different spindle speeds. Access cover With access covers open, loosen locking arm. Raise lever to release tension on motor pulley and tighten locking arm. Check speed and belt position chart inside access cover to determine spindle speed required. Move drive belt to desired pulley combination.
41 46 42 Maintenance 43 45 CAUTION! BEFORE CLEANING OR CARRYING OUT MAINTENANCE WORK, DISCONNECT THE MACHINE FROM THE POWER SOURCE (WALL SOCKET). NEVER USE WATER OR OTHER LIQUIDS TO CLEAN39 THE MACHINE. USE A BRUSH. REGULAR MAINTENANCE OF THE MACHINE WILL PREVENT UNNECESSARY PROBLEMS. 44 Keep the lathe bed casting clean and lubricated. Keep the outside of the machine clean to ensure accurate operation of all moving parts and prevent 68(3) excessive wear.
Eletrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided.
13 12 Troubleshooting
54 16 53 52 50 49 13 20 19 6 4 23 58(4) 72(2) 73(2) 24 74 59(4) 22(2) 21(2) 3 2 75 25 1 "# "pdfFactory Pro" $#%&'( ) www.fineprint.com.
Parts List KEY No. Description 70-050-1 70-050-2 70-050-3 70-050-4 70-050-5 70-050-6 70-050-7 70-050-8 70-050-9 70-050-10 70-050-11 70-050-12 70-050-13 70-050-14 70-050-15 70-050-16 70-050-17 70-050-18 70-050-19 70-050-20 70-050-21 70-050-22 70-050-23 70-050-24 70-050-25 70-050-26 70-050-27 70-050-28 70-050-29 70-050-30 70-050-31 70-050-32 70-050-33 70-050-34 70-050-35 70-050-36 70-050-37 70-050-38 70-050-39 70-050-40 Center point Faceplate Spindle Bearing Pan head screw Retaining ring Hex.
Warranty 2-Year Limited Warranty RIKON Power Tools Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail. This warranty may not be transferred. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear.
For more information: 16 Progress Rd Billerica, MA 01821 877-884-5167 / 781-933-8400 techsupport@rikontools.com www.rikontools.com Copyright RIKON Power Tools, Inc.
