Air Filtration System Owner’s Manual Model: 6 - 00 Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: For more information: www.rikontools.com or info@rikontools.com For Parts or Questions: techsupport@rikontools.
Safety Warning IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. 7KHUH DUH FHUWDLQ DSSOLFDWLRQV IRU ZKLFK WKLV WRRO ZDV GHVLJQHG :H VWURQJO\ UHFRPPHQG WKDW WKLV WRRO QRW EH PRGL¿HG DQG or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.
ALWAYS DISCONNECT TOOLS. Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters. ALWAYS AVOID ACCIDENTAL STARTING. Make sure switch is in “OFF” position before plugging in cord. NEVER LEAVE TOOLS RUNNING UNATTENDED. ALWAYS CHECK FOR DAMAGED PARTS. Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure that it will operate properly and perform its intended function.
Table of Contents Safety Warnings......................................................................................................................................2-3 Dust Collection Safety Rules....................................................................................................................... 3 Specifications.........................................................................................................................................................
Contents of Package Unpacking and Checking Contents Unpack your air filtration system from its carton and check to see that you have all of the following items. Do not turn your machine ON if any of these items are missing. You may cause injury to yourself or damage to your machine. A . Air Filtration B . Warranty Card C . Spare Parts Bag D . Remote Device E .
Getting to Know Your Air Filtration System 3 1 2 Item Description 1 Air filtration body 2 Control plate 3 Power cord Assembly The machine must not be plugged in and the power switch must be in the OFF position until assembly is complete. Tools Required for Assembly Item Description #2 Phillips Screwdriver 10mm Wrench Unpacking and Clean-up 1. Carefully finish removing all contents from shipping carton.
Assembly 1. Remove all packing and hardware from inside of the unit by removing the outer filter and inner filters. A 2. The air filtration unit can be hung from the ceiling. Hang the unit using four eyebolts (A, Fig.01). Fig.01 Four angle brackets can also be used for mounting to the ceiling, or wall. 1. Place one end of bracket underneath the lip of the cabinet. 2. Attach the bracket (A, Fig.02) with two hex cap screws (B, Fig.02) and two lock washers (C, Fig.02). 3.
Operation Remote Control: 1. The on/off button (Fig.04) turns the unit on and off. Pressing this button will start the fan on the low speed. 2. Time button (Fig.04) controls the three different settings. 2H will light up on the back of the unit with one press of the time button. The air filtration system will operate for 2 hours then shut off. 4H will light up on the back of the unit by pressing the time button twice. The air filtration system will operate for 4 hours then shut off.
Maintenance Changing the Filters ! WARNING ! To reduce the risk of injury disconnect the air cleaner from the power source (unplug) before servicing or changing filters. Failure to comply may cause serious injury! There are two filters that need to be changed. A The outer filter can be removed by disengaging the two fliter clips (A, Fig.06). Pull the filter out, or use a screwdriver to pry out the filter. Fig.06 The inner filter (Fig.07) can now be pulled out of the unit.
Notes Use this section to record maintenance, service and any calls to Technical Support: Wiring Diagram WARNING:This machine must be grounded. Replacement of the power supply cable should only be done by a qualified electrician.
Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided.
Explosion Diagram 12
Parts List KEY No. Description Part No.
Warranty 5-Year Limited Warranty RIKON Power Tools Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our SURGXFWV WKDW HDFK SURGXFW EH IUHH IURP GHIHFWV LQ PDWHULDOV DQG ZRUNPDQVKLS IRU D SHULRG RI ¿YH (5) years from the date the product was purchased at retail. This warranty may not be transferred. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs, alterations, lack of maintenance or normal wear and tear.
For more information: 16 Progress Rd Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com www.rikontools.com Copyright RIKON Power Tools, Inc.