Floodlight Wired Smart Lighting
For your safety... WARNING: Risk of electrical shock. Disconnect power at the fuse or circuit breaker before installing. Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240 VAC 50/60 Hz power source. Properly ground fixture. Always follow code standards when installing wired connections. 2 CAUTION: Risk of fire. Do not install near combustible or flammable surfaces. NOTICE: Do not connect this light fixture to a dimmer switch or timer.
1. Set up your Floodight. Download the Ring app. The app walks you through setting up and managing your Floodlight Wired. Download it on your iOS or Android device. 4 Set up your Ring Bridge. The Bridge connects your Ring Smart Lights to the Ring app and other compatible Ring devices. To set up your Bridge, follow the instructions in the Ring app or Bridge user manual.
Before you begin. Check out all the stuff in the box. Screwdriver & Reversible Bit Use to install the mounting hardware. Bag o’ Screws Find the right ones to attach the mounting hardware to your junction box without running to the hardware store. Metal Mounting Bracket Screw this into your junction box to secure the Plastic Mounting Plate. Foam Gasket Attach this to the back of the Plastic Mounting Plate to keep water and debris out of your junction box.
Shut power off at the breaker! You’ll be working with electrical wires during the install process. For safety’s sake, shut off power to your floodlight at the circuit breaker. If you don’t know where your breaker is or how to turn off power to your floodlight circuit, consult with a licensed electrician.
10 Remove your existing floodlight. Remove the bracket. With power off at the breaker, remove your existing floodlight from the junction box it’s attached to and disconnect the wires. If there is a metal bracket attached to your junction box, remove that as well. Floodlight Wired must be installed on a 4” round UL listed junction box. If you don’t have an existing junction box, you’ll need to hire a licensed electrician to install one. Be sure to comply with your local building codes.
2. Install your Floodlight. Secure the ground wire. With power turned off at the breaker, attach the ground wire from your home to the ground screw inside the junction box. The included metal mounting bracket has a hole marked “GND”. DO NOT attach the ground wire to the metal mounting bracket. Attach it to your junction box as shown here. 12 Choose your screws. Select a set of screws from the bags marked “A” through “E” that fit your junction box to secure the metal mounting bracket.
Attach the metal mounting bracket. With the screws you selected in the previous step, secure the mounting bracket to your junction box using either pair of screw holes. Be sure to align the bracket so that the “FRONT” text faces outwards.
16 Attach the foam gasket. Expose the wires. Remove the tape from the foam gasket. Press the adhesive side firmly against the rear of the plastic mounting plate, making sure to align the center screw hole and wire slot on the foam gasket with the screw hole and wire slot on the plastic mounting plate. Before securing the plastic mounting plate to your junction box, guide the wires coming from your home through the slot in the bottom of the plate to access them during installation.
Secure the plastic mounting plate. Center the plastic mounting plate over the metal mounting bracket and secure it through the center screw hole with one of the screws from the bag marked “F.” Ensure the “UP” arrow on the plastic mounting plate points upwards for wall mounting, and away from the direction you want your motion sensor and lights to point for eave and overhang mounting.
To mount on an eave or overhang... You’ll have to rotate the motion sensor in order to optimize it for horizontal motion detection. If you’re mounting vertically on a wall, skip ahead to page 24. Rotate the Motion Sensor. A Push the motion sensor to the right, then rotate it counter-clockwise 180°. B The motion sensor will now be facing the light heads, and “ring” will be upside down. You may need to hold the motion sensor’s locking collar in place while rotating to keep it from unlocking.
Complete installation. Follow the rest of the instructions in this manual or the Ring app. Once you’ve installed your Floodlight Wired should look like the image on the next page. If you need a little extra help with eave or overhang mounting, visit: ring.
Hang it up. Use the provided hook to hang your Floodlight from the installed plastic mounting plate to make wiring easier. Put one end of the hook into one of the mounting holes on your Floodlight, and the other into the slot on the plastic mounting plate.
Connect the power wires. The white wire on your Floodlight is a neutral wire. Use a wire nut from the bag marked “G” to connect the white wire from your Floodlight to the white (or neutral) wire coming from your junction box. The black wire on your Floodlight is a hot wire. Use another wire nut from the bag marked “G” to connect the black wire from your Floodlight to the black (or hot) wire from your junction box.
Mount your Floodlight. Lift the Floodlight off of the hook, and remove the hook from the mounting plate. Push the wires through the slot in the plastic mounting plate and back into the junction box. Slide your Floodlight over the posts on the mounting plate. Grab a couple of screws from the bag marked “H” and use them to mount your Floodlight.
Switch power back on. You’re all set! Feel free to turn the power back on at the breaker. Your Floodlight will flash twice (and you may hear a “click”) to let you know it’s in Setup Mode. 30 Set up your Floodlight Wired in the Ring app. In the app, tap Set Up a Device. When prompted, select Smart Lighting and follow the in-app instructions.
For additional help, visit: ring.com/help Or give us a call… US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents © 2019 Ring LLC or its affiliates. Ring, Alexa, Always Home, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.