Spotlight Cam Wired
Smart Security at Every Corner of Your Home Your new Spotlight Cam lets you extend the Ring of Security around your entire property. Now, you’ll always be the first to know when someone’s on your yard, and you can watch over your home from anywhere. Monitor your home, prevent crime and protect your property – all from your phone, tablet or PC.
Contents 1. In-app Setup 2. Physical Installation 3. Features 4.
1. Set up your Spotlight Cam in the Ring app.
Download the Ring app The Ring app will walk you through setting up and managing your Spotlight Cam. Search for “Ring” in one of the app stores below, or visit: ring.com/app. Download from Windows Store Grab your Wi-Fi password It’s required for the in-app setup.
Plug your Spotlight Cam into a power outlet Plug your Spotlight Cam into an outlet in the same room as your Wi-Fi router to set it up.
Set up your Spotlight Cam in the Ring app In the Ring app, select Set Up Device. When prompted, select Spotlight Cam Wired and follow the in-app instructions.
Try it out! After setup, select the Live View button to see video from the camera in the Ring app.
White light flashing? If the light on the bottom of your Spotlight Cam is flashing after setup, it’s updating its internal software. The light will stop flashing when the update is completed. This update can take up to a few minutes.
Test video quality outside Now, unplug your Spotlight Cam and take it outside to where you want to install it. Plug Spotlight Cam into an outdoor outlet and test video quality again. Everything look good? Continue to the next section. Something not right? Jump ahead to the troubleshooting section.
2. Install your Spotlight Cam on the wall.
Before you begin This is everything you’ll need to install your Spotlight Cam. Screwdriver Use the screwdriver handle to hold the provided bit. Phillips Bit Use the Phillips bit for installing the mounting bracket and tightening the security screw. Drill Bit Use this to pre-drill holes if installing on a masonry surface, such as stucco or brick. Mounting Bracket Attach this to the wall first, then slot Spotlight Cam into the mounting bracket. It also features a built-in level.
Install Screws (5) Use these to install the mounting bracket on your wall. Wall Anchors (16) Use these to attach the mounting bracket and the cable clips to your wall, if installing on a masonry surface, such as stucco or brick. Cable Clips (11) Use these to attach the power cable to your wall.
How it all fits together Setup Button Lights 14 Motion Detector
Install Screws Mounting Bracket Security Screw Wire Clip 15
Select an install height When mounted at 9 feet off the ground, with the motion detector parallel to the ground, the motion sensor is optimized to detect humansized objects at up to 30 feet.
Parallel to ground 9 feet (3 Meters)
Install the mounting bracket Use the built-in level to make sure your Spotlight Cam will be level before marking your holes. If installing on a masonry surface, first drill holes using the provided drill bit. Insert the wall anchors before installing the screws. If installing on a wood surface, use the install screws to screw the mounting bracket directly into your wall.
Attach the base of Spotlight Cam to the mounting bracket Slot the base down to lock it to the mounting bracket.
Tighten the security screw Using the Phillips end of the screwdriver bit, tighten the security screw on the right until your Spotlight Cam is secure.
Secure the cable Use the provided cable clips to secure the cable on your wall. Use the included drill bit to predrill holes in the wall and insert the provided anchors first if installing on a masonry surface, like stucco or brick. The power cable can be painted to match the wall.
Plug Spotlight Cam in If Spotlight Cam is not already plugged into a power outlet, plug it in now. If you’ve already completed the inapp setup, wait about a minute for Spotlight Cam to power up and come back online.
Adjust the camera angle To ensure accurate motion detection, position the camera with the motion detector parallel to the ground. Tighten the side screw on the left to secure the camera position.
3. Check out all the exciting features.
After setup, select your Spotlight Cam in the Ring app This will bring you to the Device Dashboard, where you can change settings and access various features.
Manually switch the lights on or off. Turn notifications on or off for motion events. Trigger the siren to scare away intruders. Tap to see live video from Spotlight Cam. From here, you can see, speak and hear visitors, and control the siren and lights.
View a log of all the events captured by your Spotlight Cam in Event History. Visit Device Health to diagnose any problems you run into. Select Motion Settings to customize motion detection settings. Adjust the areas that trigger the lights, change the brightness of the lights and set a timer for lights to stay on in Light Settings.
Motion Detection To detect motion, you will need to set up Motion Zones, which are customizable areas you want your Spotlight Cam to monitor and receive alerts about. To set up a Motion Zone, select Motion Settings. On this screen, create up to three Motion Zones. You will need at least one Motion Zone to be active to get alerts.
Notifications If your phone is locked when the camera captures a live event, you will receive a notification on your home screen. If your phone has a passcode, you’ll need to enter it to access the live event.
Live Events A live event begins when motion is detected or when selecting Live View. During live events, you can access these features: Two-way Talk – Speak to visitors and hear what they have to say. Siren – Activate the siren. Lights – Turn the lights on and off. Ring Neighborhoods – Share suspicious events with neighbors.
Ring Video Recording This optional feature saves recordings of every event your Spotlight Cam captures, allowing you to share it with others. You can access these events on any device running the Ring app or by logging into your account at: ring. com/activity. Learn more at: ring.com/video-recording Your new Spotlight Cam includes a free trial of Ring Video Recording for you to enjoy. Watch your email inbox for important announcements about this service.
Select Motion Settings to customize your motion preferences 38
Adjust the amount of alerts you receive. Choose People Only to get motion alerts triggered by humans only. Draw up to three custom areas where you’d like to receive motion alerts and trigger the lights at night. Schedule times when you don’t want to receive motion alerts.
Select Light Settings to set a schedule for your lights to stay on.
Select Advanced Settings on the Light Settings screen to customize the areas that will trigger the lights and set how long they stay on after motion is detected.
4.
Spotlight Cam is not powering up. See if there is a light switch controlling power to the outlet Spotlight Cam is plugged into. If so, make sure it is switched on and stays switched on. I’m having trouble completing the in-app setup When the in-app setup fails, look at the light on the bottom of your Spotlight Cam. The light color indicates the issue. Flashing red means your Wi-Fi password was entered incorrectly.
Why can’t I find the temporary Ring network on my phone? Sometimes your phone fails to pick up the temporary Ring network. If this happens, go to your phone settings, turn off your Wi-Fi connection, wait 30 seconds and turn it back on. If the Ring network still fails to appear, check that your Spotlight Cam is connected to power. If none of the above helped… Perform a hard reset on your Spotlight Cam by holding down the setup button for 15 seconds, waiting 30 seconds and repeating the setup process.
Why can’t visitors hear me on my Ring when I talk through the app? If you’re on an iPhone or iPad, check the microphone permission on your device. Select Settings, find Ring and select it. Also make sure that the switch next to Microphone is toggled on. If you’re on an Android device, go to Settings > Application/Apps > Application Manager > Ring > Permissions. Ensure everything here is on. Spotlight Cam lights up, but I can’t complete the in-app setup.
Why is my video and/or audio quality poor? First, determine the cause. Remove your Spotlight Cam and bring it inside near your router. Open the Ring app, and press the Live View button, or trigger a motion event to see live video. If you get good video quality near the router, you need to extend your Wi-Fi signal. We recommend Ring Chime Pro to boost the signal to your Spotlight Cam. Learn more at: ring.
For additional help, visit: ring.com/help Or give us a call… US 1 800 656 1918 UK 01727 263045 FR +80087009781 DE +80087009781 AU 1 300 205 983 NZ +64 9 887 9871 Mexico (D.F) 52 55 8526 5445 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.