Installation Guide

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
For best results, use type Li-Ion batteries. Install only new
batteries of the same type in your product. Failure to insert
batteries in the correct polarity, as indicated in the battery
compartment, may shorten the life of the batteries or cause
batteries to leak. Do not mix old and new batteries. Do not
mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel
Cadmium) or (Nickel Metal Hydride) batteries. Do not dispose of
batteries in fire. Batteries should be recycled or disposed of as
per state and local guidelines.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Hereby, Bot Home Automation, declares that this consumer
electronic is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC. The declaration
of conformity may be consulted at www.ring.com/DoC.pdf.
Protect the device from direct sunlight. Install the device at dry
locations and protect it against rain and humidity. The device
may not get contact to salt water or other conductive liquids. The
device must be charged only within a building in a dry state.
Step 6
Connect the wires (optional)
Connect the wires coming out of
your wall to the screws on the
bracket. Note that it doesn’t matter
which wire connects to which screw.
The wiring must be connected
to a transformer with a voltage
of 8VAC – 24VAC and an internal
doorbell or resistor.
DC transformers and (therefore)
most intercoms are not supported.
If you have a digital doorbell,
connecting the diode the wrong way
won’t do any harm. If your doorbell
doesn’t ring, just reverse the diode.
Learn more at ring.com/diode
How and when to
use the diode
If your doorbell is digital (i.e. plays a
melody), attach the included diode to
the two screws on your bracket.
If it’s mechanical (i.e. goes “ding-
dong”), DO NOT use the diode.
First, make sure the
security screws are
loose.
Step 7
Attach Ring Doorbell to the bracket
Line up the holes in your Ring
Doorbell with the slots on the
bracket. Push firmly towards the wall
and then down until you feel a click.
Step 8
Secure your Ring Doorbell
Use the star-shaped end of your Ring
screwdriver to tighten the security
screws on the bottom of
your Ring Doorbell.
Then, restore
power at the
breaker.
Ring Light Patterns
The front light on your Ring Doorbell
uses a number of patterns to
communicate messages.
Here are some common ones:
Blue
Spinning
Front Button
Pushed
White
Solid
Wired
Charge
Percentage
Charging
White
Spinning
In Setup
Mode
White
Flashing
Updating
Software
Blue
Solid
Ring Speaker
Enabled
Answering Your Door
When someone is at your door, you
can perform the following actions:
Turning alerts on or off:
Disable/enable your
microphone
Mute/unmute your speaker
Zoom in/out
Access the Ring Plus menu
You can toggle
alerts for Rings or
Motions on or off
in the Ring app.
© 2016 Bot Home Automation, Inc.
RING, ALWAYS HOME, and CHIME are trademarks
of Bot Home Automation, Inc.
1523 26th St.
Santa Monica, CA
90404
Last updated: 01/19/18
Need Help?
For additional help, visit:
ring.com/help
For immediate assistance, we’re
available 7 days a week at:
[e-mail]
US 1 800 656 1918
UK 01727 263045
AU 1 300 205 983
NZ [phone]
Mexico (D.F) 52 55 8526 5445
Worldwide [phone]
For a list of all our customer support
numbers, visit: ring.com/callus
Installing the mounting bracket
(continued)
Drive the screws into the anchors
or directly into the wall until they’re
flush with the mounting
bracket and the bracket
is flat against the wall.
If the wall isn’t flat,
make sure you don’t
screw the bracket in so
tightly that it bends.
10 11 12 13 14 15 16 17 18