User Guide

ManualsBrandsRing ManualsBridge Proring Amazon Sidewalk Bridge Pro

Amazon Sidewalk Bridge Pro by Ring Setup Guide

copy

Welcome to the setup and installation instructions for Amazon Sidewalk Bridge Pro by Ring – the professional-grade bridge

for

businesses, municipalities, universities, and public services that helps extend connectivity to compatible Amazon Sidewalk

devices in communities.

This device must be installed by a professional installer or licensed electrician. Please follow the instruction below very

carefully.

Overview

Hardware

●

Base Unit Package

Antenna Package

Additional Equipment/Tools Checklist

Site Survey Checklist

Installation

Pre-Wiring

Install Antenna

Install Antenna Cable Connection

Install Base Unit

Hardware

Base Unit Package

1 Base Unit (with a grounding connector screw attached on the bottom)

2 Base Unit Mounting Bracket

Draft

Summary of content (10 pages)

PAGE 1
Amazon Sidewalk Bridge Pro by Ring Setup Guide copy Welcome to the setup and installation instructions for Amazon Sidewalk Bridge Pro by Ring – the professional-grade bridge for businesses, municipalities, universities, and public services that helps extend connectivity to compatible Amazon Sidewalk devices in communities. This device must be installed by a professional installer or licensed electrician. Please follow the instruction below very carefully.
PAGE 2
1 Screw Pack (P6.035L+Anchor D1043L+FM3*17.5L), 2 Bracket Clamp Hose 1 Waterproof Gasket 1 Cable Gland Antenna Package Antenna Mounting Bracket 1 Screw Pack (P6.
PAGE 3
Additional Equipment/Tools Checklist (Not Included) In order to complete the installation, you'll need the following items. They must be purchased separately. ● 1 x PoE+ Injector ○ 802.3at compliant ○ For PoE+ connection, use only UL listed L.T.E. with PoE+ output ○ A waterproof box to install the PoE+ injector inside if the PoE+ injector has to be placed outdoors.
PAGE 4
reach both sides. This device is powered through PoE+, the installer should locate the power source on the building roof or inside the building. If the purchased PoE+ injector is not waterproof or identified for outdoor usage, please install it indoors. This device should connect grounding wires to the local grounding terminal. The installer should locate the grounding terminals on the building roof or inside the building.
PAGE 5
ft ra 1. Pre-Wiring ● Prior to wiring, lay down the Ethernet cable from the mounting pole to the building power source. ● Crimp the RJ 45 connector on Ethernet cable’s remote end (close to the building power source). D ● Follow the below process to make the RJ 45 connector at the Ethernet cable’s local end (close to the mounting pole) with the waterproof gasket and cable gland provided in the base unit package. ● Figure A: Remove the waterproof gasket from cable gland and packaging.
PAGE 6
○ Don’t plug in the Ethernet cable’s local RJ 45 connector in the base unit port until all installation work is finished. ft ○ Don’t plug the PoE+ adapter connector into the building power source until all installation work is finished. ra ● Figure D: Lay down the five (5) grounding wires between the mounting pole and the building grounding terminal. ● Figure D: Crimp the five (5) grounding connectors on each of the grounding cables at the remote end (close to the building grounding terminal).
PAGE 7
○ Figure F: Pass the 3-foot antenna cable through the hole one by one. ○ Figure G: Connect the cable to the four (4) antenna connectors using the installation steps. ○ Figure J: Put the antenna cover on. ft ○ Figure H: Fix the antenna mounting bracket on the mounting pole and tighten the two(2) pipe clamps. ○ Figure K: Tighten the four (4) screws with an H2.5 screwdriver. ra 3. Antenna Cable Connection Orders ○ Figure L: Use a 12-gauge or smaller wire gauge to connect the connectors.
PAGE 8
4. Install the Base Unit ○ Figure M: Disassemble the grounding screw from the bottom of the base unit. ○ Figure N: Crimp the connector on the grounding wire. ○ Figure N: Attach the connector to the grounding wire on the bottom of the base unit. D ra ft ○ Figure P: Tighten the grounding screw. ● Figure Q: Fix the base unit bracket on the mounting pole. ● Figure R: Tighten the two pipe clamps. ● Figure S: Fix the base unit into its mounting bracket, aligning the mounting holes.
PAGE 9
D ra ft ● Figure U & X: Crimp and connect the grounding wires on each RF lighting arrestor. ● Figure Y: Connect the POE+ cable with the cable gland to the device’s Ethernet port (the base unit should be automatically powered on from here). ● Figure Z: After connecting, tighten the cover of the cable gland.
PAGE 10
APPENDIX Ring Help URL: https://support.ring.com/hc/en-us/articles/8704165001236 Anchor Links: ● Hardware: https://support.ring.com/hc/en-us/articles/8704165001236#hardware ● Base Unit Package: https://support.ring.com/hc/en-us/articles/8704165001236#basepackage ● Antenna Package: https://support.ring.com/hc/en-us/articles/8704165001236#antennapackage ● Additional Equipment/Tools Checklist: https://support.ring.com/hc/en-us/articles/8704165001236#extraequipment ● Site Survey Checklist: https://support.