Video Doorbell 3 1
1. Charge the provided battery. Plug the battery in. First, fully charge the battery by plugging it into a power source using the provided orange cable. The small light on top will glow green once fully charged.
Insert the battery. After charging, insert the battery in the bottom of your Video Doorbell until it clicks into place. 4 2. S et up your Video Doorbell in the Ring app.
Download the Ring app. Set up your Video Doorbell near your Wi-Fi router. The Ring app walks you through setting up and managing your Video Doorbell. In the Ring app, select Set Up a Device. Search for “Ring” in one of the app stores below, or visit: ring.com/app When prompted, select Doorbells, and follow the in-app instructions. Download from Windows Store Grab your Wi-Fi password It’s required for the in-app setup.
Try it out! After setup, push the button on the front of your Video Doorbell to see video from the camera in the Ring app. Smile, you’re on camera! 8 3. Install your Video Doorbell.
Select your install height. Install Video Doorbell approximately four feet (1.20 metres) above the ground for optimal performance. If you’re connecting to existing doorbell wiring that’s higher than four feet, thus limiting where you can install your new Doorbell, use the provided wedge mount to angle your Doorbell down. Camera field of view Motion detection range 4 feet (1.
Steps for wiring to an existing doorbell Remove your existing doorbell. (optional) If replacing an existing doorbell, shut off power at the breaker. Then remove it from the wall and disconnect the wires. Your Video Doorbell is compatible with doorbell systems supplying 8-24 volts AC at 50 or 60Hz, 40VA max. Do not wire your Video Doorbell to a DC-powered intercom system or other DC power source. Do you have an in-home chime? If desired, the chime can ring when the button on your Ring Doorbell is pressed.
Steps for wiring to an existing doorbell Install the anchors. (optional) Connect the wires. (optional) If installing on stucco, brick, or concrete, mark 4 drill holes. Use the provided masonry drill bit to drill holes in your wall, then insert the included anchors. Connect the wires coming out of your wall to the screws on the back of your Video Doorbell. Either wire can connect to either screw. The order doesn’t matter.
Steps for wiring to an existing doorbell Attach the wire extensions. (optional) If you have trouble connecting the wires coming out of your wall to the back of your Video Doorbell, use the provided wire extensions and wire nuts. 16 Screw it in. Feed all the wires (and the wire nuts, if you used them) into your wall and secure your Video Doorbell on the wall using four screws.
Install the faceplate. Secure the faceplate. Place one of the provided faceplates on your Video Doorbell by slotting it in at the top and clicking it into place. Lastly, insert one of the provided security screws into the bottom, and tighten with the starshaped end of the screwdriver bit. That’s it! Your Video Doorbell is now ready to use.
For additional help, visit: ring.com/help Or give us a call… US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 AU 1 300 205 983 NZ +64 9 887 9871 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. © 2020 Ring LLC or its affiliates. Ring and all related logos are trademarks of Ring LLC or its affiliates.
User Guide Video Doorbell 3
1. Charge the battery. Plug in the battery. Insert the battery. First, fully charge the battery by plugging it into a power source using the provided orange cable. After charging, insert the battery in the bottom of your Video Doorbell until it clicks into place. The small light on top will glow green once fully charged.
2. Set up your Video Doorbell. Download the Ring app. Set up your Video Doorbell near your wifi router. The Ring app walks you through setting up and managing your Video Doorbell. In the Ring app1 select Set Up a Device. Search for "Ring" in one of the app stores below1 or visit ring.com/ app When prompted 1 select Doorbells, and follow the in-app instructions. ~ GET ITON ,,. ./ Google Play Try it out.
3. Install your Video Doorbell. Set your install height. Install your Video Doorbell approximately four feet (1.20 metres) above the ground for optimal performance. I. If you're connecting to existing doorbell wiring that's higher than four feet and want to angle your Video Doorbell down for a better view, you can purchase a Wedge Kit online at ring.com/ accessories. I Camera field of view '-....... Motion detection range ..............
Steps for wiring to an existing doorbell Remove your existing doorbell. (optional) Insert the included mini-level. If replacing an existing doorbell, shut off power at the breaker. Then remove it from the wall and disconnect the wires. This helps to ensure the camera is parallel to the ground when you install your Doorbell. Your Video Doorbell is compatible with doorbell systems supplying 8-24 volts AC at 50 or 60Hz, 40VA max. 0 Do not wire you• Vdf'o Doorbc to a DC-powered 1'1tE'rc.om <:.
Steps for wiring to an existing doorbell Install the anchors. (optional) Connect the wires. (optional) If installing on stucco, brick, or concrete, mark 4 drill holes. Use a 1/4" masonry drill bit to drill holes in your wall, then insert the included anchors. Connect the wires coming out of your wall to the screws on the back of your Video Doorbell. If you're installing on wood, skip this step. 10 It doesn't matter which wire goes to each screw, as long as both screws are connected.
Steps for wiring to an existing doorbell Attach the wire extensions. (optional) Screw it in. If you have trouble connecting the wires coming out of your wall to the back of your Video Doorbell, use the provided wire extensions and wire nuts. Feed all the wires (and the wire nuts, if you used them) into your wall and secure your Video Doorbell on the wall using the provided screws.
Install the faceplate. Secure the faceplate. Place the faceplate on your Video Doorbell by slotting 1t in at the top and clicking it into place. Lastly, insert one of the provided security screws into the bottom, and tighten with the included screwdriver. Your Video Doorbell is now ready to use. - - I I I I ·I ~ ....
Review, share and download. Your new device comes with a free 30-day trial of Ring Protect video recording service. To continue your subscription and save your videos, please visit: ring .
• ring What is Ring Protect? Ring Protect is a subscription service that stores videos from your Ring devices. For additional help, visit: ring.com / help Or give us a call: Why do I want it? us 1 800 656 191 8 Ring lets you interact with visitors and monitor your property in real time, while Ring Protect allows you review and share those videos anytime. ..
Quick Start 1. Remove battery. Charge before use. 2. Open the Ring app and select Set Up Device. Then follow the in-app instructions. 3. Scan this code. This identifies your Ring device to make setup fast and easy. I!] i I!] • ~ 77865 • For additional help, visit ring.
Optional Wedge and Corner Mounts Need to angle your Ring towards your walkway? Is your door up a staircase or hill, or facing a street? Install the Corner Mount. Install the Wedge Mount.. II, Wedge and Corner Mounts can be painted to match your home.
Setup Steps ... 1. Download t he Ring app. Open the Ring app) create an account, and select Set Up a Device. 2. Scan this code. This identifies your Ring to make setup fast and easy. 76012 3. Complete your setup. Continue setup in the Ring app) then install your Ring Doorbell following the supplied instructions .
Get the most from your Ring. Your Ring Video Doorbell 3 comes with a free 30 day trial of our Ring Protect video recording service. It's great for keeping track of what happens at your doorstep. Sign up today. Your first 30 days are still free . To extend your subscription and save your videos, visit: ring.
Q: What is Ring Protect? Ring Protect is a subscription service that stores videos of every event your Ring products capture. Videos are stored for up to 60 days and can be downloaded for long-term storage. Q: Why do I want it? Out of the box1 your Ring lets you interact with visitors and monitor your property in real time. 1 If you d like to be able to review your Ring videos anytime and share them with anyone1 Ring Protect is for you.
• 1523 26th St. Santa Monica) CA 90404 & IMPORTANT PRODUCT INFORMATION SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. Your device can withstand outdoor use and has been tested to withstand water projected thr\)ugh a 6.3mm nozzle at a volume of 12.5 liters per minute and a pressure of 30 kPa at a distance of 3 meters for at least 3 minutes. However, your device is not intended for underwater use.
For Consumers in the USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
For Consumers in Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a maJor failure.
Important Product Information IMPORTANT PRODUCT INFORMATION & SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. Your device can withstand outdoor use and has been tested to withstand water projected through a 6.3mm nozzle at a volume of 12.5 liters per minute and a pressure of 30 kPa at a distance of 3 meters for at least 3 minutes. However, your device is not intended for underwater use.
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there Is no guarantee that interference will not occur in a particular installation.
At Ring, our mission is to reduce crime in neighborhoods. Let every visitor know your home is protected by Ring with this sticker. Connect with us and share pictures of where you stick it at: 0 0 twitter.com/ring @ instagram.com/ring facebook.
