Setup Guide Doorbell Pro 2
Included installation hardware. Download the Ring App. Bag The Ring App walks you through setting up and managing your Ring Doorbell. Hardware A (2) 1-3/8" Long Mounting Screws Search for “Ring” in one of the app stores below, or visit ring.com/app (2) Wall Anchors B C D (2) 3/16" Security Screws Set up your Ring Doorbell. (2) 5/8" Short Mounting Screws In the Ring app, select Set Up a Device and follow the in-app instructions.
Turn off power at the breaker. Grab the included Pro Power Kit. This is essential to keeping you and your new Ring Doorbell safe. The Pro Power Kit ensures that your Ring Doorbell gets the power it needs, and must be installed before you install your Ring Doorbell. If you’re not sure which breaker controls your doorbell chime, turn off the master breaker for your home, or contact an electrician. Your Ring Doorbell is compatible with doorbell systems supplying 16–24 volts AC at 50 or 60Hz, 40VA max.
Remove the cover from your doorbell chime. After you’ve turned off power at the breaker, remove the cover from your chime and set it aside for now. Loosen the “Front” and “Trans” terminal screws. Connect the Pro Power Kit wires. Connect one wire from the Pro Power Kit to the “Front” terminal, and the other to the “Trans” terminal. It doesn’t matter which wire you connect to which terminal. Then re-tighten the terminal screws. Make sure to keep the existing doorbell wires in place.
Uninstall your existing doorbell button. Install the included Corner Mount. (optional) Remove your doorbell from the wall. Disconnect the wires. Make sure they don’t fall back inside your wall so you can access them later. The Corner Mount can angle your Ring Doorbell to improve motion detection and provide a better view. Remove the faceplate. Grasp the bottom of the faceplate and pull to remove. Mark two mounting holes on your wall through the slots on your Corner Mount (fig 1).
Install the anchors. (optional) On stucco, brick, or concrete, use a 1/4" masonry bit to drill holes in your wall, then insert the included wall anchors. (If you’re installing on wood or siding, you can skip this step.) Screw in the Corner Mount. Using the long mounting screws, secure the Corner Mount to the wall through the slots (fig. 3). If you’re re-using existing holes, secure it with the adjacent screw holes (fig. 4). fig.
Connect the doorbell wires. Loop one doorbell wire around each of the screw terminals on the rear of your Ring Doorbell then tighten the terminals to secure. If your doorbell wires are too short to reach your new Ring Doorbell, you can attach the included wire extenders using the included wire nuts. 12 Mount your Ring Doorbell to the Corner Mount. Secure your Ring Doorbell to the Corner Mount with the two included short mounting screws. Be sure to feed any excess wiring back into the wall first.
Mark the screw holes. DO NOT USE any screw other than the included short mounting screws when securing your Ring Doorbell. 5/8" Short mounting screw Using your Ring Doorbell as a template, mark the location of the two mounting holes on your wall.
Install the anchors. (optional) On stucco, brick, or concrete, use a 1/4" masonry bit to drill holes in your wall, then insert the included wall anchors. (If you’re installing on wood or siding, you can skip this step.) 16 Connect the doorbell wires. Loop one doorbell wire around each of the screw terminals on the rear of your Ring Doorbell then tighten the terminals to secure.
Screw in your Ring Doorbell. Restore power at the breaker. Mount your Ring Doorbell with the two included long mounting screws. It may take a moment for your Ring Doorbell to power on. You’ll know it’s ready once it lights up and speaks to you. Be sure to feed any excess wiring back into the wall first. If you used the wire nuts, push them through the hole as well. DO NOT USE any screw other than the included long mounting screws when securing your Ring Doorbell.
Secure your Ring Doorbell. Free Ring Protect Plan for 30 days. Re-attach the faceplate, then use the included screwdriver to drive the small security screw into the bottom of your Ring Doorbell. Your new device comes with a free, 30-day trial of Ring Protect. This comprehensive subscription service lets you review, save, and share your video and photo history anytime so you never miss a moment.
For additional help, visit ring.com/help Or give us a call: US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit ring.com/callus For information on our warranty, theft protection, and Ring Protect Plans, see ring.com/legal © 2022 Ring LLC or its affiliates. Ring and all related marks are trademarks of Ring LLC or its affiliates.