Setup Guide Doorbell Pro
Quick Start Included installation hardware. Bag 1. Open the Ring app and select Set Up Device. Then follow the in-app instructions. 2. Scan this code. This identifies your Ring device to make setup fast and easy. A Hardware (3) 1" Mounting Screws (3) Wall Anchors B C (2) 3/16" Security Screws (2) 1-1/4" Short Bracket Screws QR+FR (2) 1-1/2" Medium Bracket Screws (2) 2" Long Bracket Screws (2) Wall Anchors D For additional help, visit ring.
Download the Ring App. Turn off power at the breaker. The Ring App walks you through setting up and managing your Ring Video Doorbell Pro. This is essential to keeping you and your new Ring Doorbell safe. Search for “Ring” in one of the app stores below, or visit ring.com/app If you’re not sure which breaker controls your doorbell chime, turn off the master breaker for your home, or contact an electrician. Set up your Ring Doorbell.
Grab the included Pro Power Kit. The Pro Power Kit ensures that your Ring Doorbell gets the power it needs, and must be installed before you install your Ring Doorbell. Your Ring Doorbell is compatible with doorbell systems supplying 16–24 volts AC at 50 or 60Hz, 40VA max. Remove the cover from your doorbell chime. After you’ve turned off power at the breaker, remove the cover from your chime and set it aside for now. Loosen the “Front” and “Trans” terminal screws.
Connect the Pro Power Kit wires. Connect one wire from the Pro Power Kit to the “Front” terminal, and the other to the “Trans” terminal. It doesn’t matter which wire you connect to which terminal. Then re-tighten the terminal screws. Uninstall your existing doorbell button. Remove your doorbell from the wall and disconnect the wires. Make sure they don’t fall back inside your wall so you can access them later. Remove the faceplate.
Install the included Corner or Wedge Mount. (optional) Install the anchors. (optional) The Corner and Wedge Mounts can angle your Ring Doorbell to improve motion detection and provide a better view. On stucco, brick, or concrete, use a 1/4" masonry bit to drill holes in your wall, then insert the included wall anchors. First, position your chosen mount on your wall, and feed your doorbell wires through the center hole.
Screw in the Corner or Wedge Mount. Connect the doorbell wires. Using the short bracket screws, secure the Corner or Wedge Mount to the wall. You’ll use the 1" mounting screws to attach your Doorbell to the bracket later. Loop one doorbell wire around each of the screw terminals on the rear of your Ring Doorbell then tighten the terminals to secure. If your doorbell wires are too short to reach your new Ring Doorbell, you can attach the included wire extenders using the included wire nuts.
Mount your Ring Doorbell to the Corner or Wedge Mount. Secure your Ring Doorbell to the Corner or Wedge Mount with two of the included 1" mounting screws. Mark the screw holes. Using your Ring Doorbell as a template, mark the location of the two mounting holes on your wall. Be sure to feed any excess wiring back into the wall first. If you used the wire nuts, push them through the hole as well. Once you’re done, skip ahead to page 18.
Install the anchors. (optional) On stucco, brick, or concrete, use a 1/4" masonry bit to drill holes in your wall, then insert the included wall anchors. (If you’re installing on wood or siding, you can skip this step.) 16 Connect the doorbell wires. Loop one doorbell wire around each of the screw terminals on the rear of your Ring Doorbell then tighten the terminals to secure.
Screw in your Ring Doorbell. Restore power at the breaker. Mount your Ring Doorbell with two of the included 1" mounting screws. It may take a moment for your Ring Doorbell to power on. You’ll know it’s ready once it lights up and speaks to you. Be sure to feed any excess wiring back into the wall first. If you used the wire nuts, push them through the hole as well. DO NOT USE any screw other than the included 1" mounting screws when securing your Ring Doorbell.
Secure your Ring Doorbell. Free Ring Protect Plan for 30 days. Re-attach the faceplate, then use the included screwdriver to insert and tighten one of the 3/16” Security Screws. Your new device comes with a free, 30-day trial of Ring Protect. This comprehensive subscription service lets you review, save, and share your video and photo history anytime so you never miss a moment.
For additional help, visit ring.com/help Or give us a call US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit ring.com/callus For information on our warranty, theft protection, and Ring Protect Plans, visit ring.com/legal © 2022 Ring LLC or its affiliates. Ring and all related marks are trademarks of Ring LLC or its affiliates.
