User Manual

IMPORTANT PRODUCT INFORMATION
SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
BATTERY SAFETY
Keep the battery and its power adapter in a well-ventilated area and away from heat sources, especially when in use or charging. Do
not charge your battery near water or in extremely humid conditions. Do not open, disassemble, bend, deform, puncture or shred the
battery. Do not modify, attempt to insert foreign objects into the battery or immerse or expose to water or other liquids. Do not expose
the battery to fire, explosion or other hazard. Promptly dispose of used batteries in accordance with applicable laws and regulations. If
dropped and you suspect damage, take steps to prevent any ingestion or direct contact of fluids and any other materials from the battery
with skin or clothes.
For best results, use type Li-Ion batteries. Install only new batteries of the same type in your product. Failure to insert batteries in the
correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause batteries to leak. Do not mix old
and new batteries. Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) batteries.
Always remove old, weak, or worn out batteries promptly and recycle or dispose of them in accordance with Local and national disposal
regulations.
If a battery leaks, remove all batteries and recycle or dispose of them in accordance with battery manufacturer’s recommendations. If fluid
from the battery comes into contact with skin or clothes, flush with water immediately.
Protect the device from direct sunlight. Install the device at dry locations and protect it against rain and humidity. The device may not get
contact to salt water or other conductive liquids. The device must be charged only within a building in a dry state.
Safely Connecting Your Ring Video Doorbell 3 to your Home’s Electrical Wiring
If you install the Ring Video Doorbell 3 where a doorbell is already in use and you connect the Ring Video Doorbell 3 to your home’s
doorbell electrical wiring, you must turn off the existing doorbell’s power source at your home’s circuit breaker or fuse and test that the
power is off BEFORE removing the existing doorbell, installing the Ring Video Doorbell 3, or touching electrical wires. Failure to turn off
circuit breaker or fuse so could result in FIRE, ELECTRIC SHOCK, or OTHER INJURY or DAMAGE.
More than one disconnect switch may be required to turn off the equipment before servicing.
To test whether you have successfully de-energized your existing doorbell’s power source, press your doorbell several times to confirm
that the power is off.
If the electrical wiring in your home does not resemble any of the diagrams or instructions provided with Ring Video Doorbell 3, if you
encounter damaged or unsafe wiring, or if you are unsure or uncomfortable in performing this installation or handling electrical wiring,
please consult a qualified electrician in your area.
Only use accessories that are recommended by the manufacturer. Use of third-party accessories may lead to damage to your Ring Video
Doorbell 3 or the accessory and may cause fire, electric shock, or injury.
Product Specifications
Model Number: 5AT3S9
Electrical Rating: Can connect to a doorbell system supplying 8-24 VAC for continuous charging and internal doorbell control
Temperature Rating: -20°C to 50°C
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by
inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form available at https://www.fcc.gov/oet/
ea/fccid.
The party responsible for FCC compliance is:
Ring LLC
1523 26th Ave
Santa Monica, CA USA
90404
Device Name: Video Doorbell 3
Model: 5AT3S9
1523 26th St.
Santa Monica, CA 90404
RVD3_Insert_legal_cert.indd 1 10/8/19 12:44 AM