Video Doorbell 3 1 RVD3_manual_NO-DIODE.
RVD3_manual_NO-DIODE.indd 3 2 1. Charge the provided battery. = Charging 3 10/8/19 12:31 AM If you can’t wait to play with your Video Doorbell, go ahead and set it up. But, we recommend fully charging it before installation. = Charged The small light on top will glow green once fully charged. First, fully charge the battery by plugging it into a power source using the provided orange cable. Plug the battery in.
RVD3_manual_NO-DIODE.indd 5 4 After charging, insert the battery in the bottom of your Video Doorbell until it clicks into place. Insert the battery. 2. Set up your Ring Video Doorbell 3 in the Ring app.
RVD3_manual_NO-DIODE.indd 6-7 Your Wi-Fi password It’s required for the in-app setup. Write it down below so it’s handy when you need it: Grab your Wi-Fi password Search for “Ring” in one of the app stores below, or visit: ring.com/app The Ring app walks you through setting up and managing your Video Doorbell. Download the Ring app. 6 When prompted, select Doorbells, and follow the in-app instructions. In the Ring app, select Set Up a Device. Set up your Video Doorbell near your Wi-Fi router.
RVD3_manual_NO-DIODE.indd 9 8 Smile, you’re on camera! After setup, push the button on the front of your Video Doorbell to see video from the camera in the Ring app. Try it out! 3. Install your Ring Video Doorbell 3.
RVD3_manual_NO-DIODE.indd 11 Motion detection range If you’re connecting to existing doorbell wiring that’s higher than four feet, thus limiting where you can install your new Doorbell, use the provided wedge mount to angle your Doorbell down. Install Video Doorbell approximately four feet above the ground for optimal performance. Select your install height.
RVD3_manual_NO-DIODE.indd 13 12 Do not wire your Video Doorbell to a DC-powered intercom system or other DC power source. If wiring directly to a doorbell transformer, connect a 25 ohm, 50W wirewound resistor in series with one of the doorbell wires to protect your Video Doorbell. This enhances performance and extends battery life. If your doorbell transformer supplies 8-24 volts AC, we suggest wiring in your Video Doorbell. If replacing an existing doorbell, shut off power at the breaker.
RVD3_manual_NO-DIODE.indd 15 14 If you’re installing on wood, skip this step and toss the anchors in that drawer of stuff you never use. 15 10/8/19 12:31 AM Connect the wires coming out of your wall to the screws on the back of your Video Doorbell. If installing on stucco, brick, or concrete, mark 4 drill holes. Use the provided masonry drill bit to drill holes in your wall, then insert the included anchors. Either wire can connect to either screw. The order doesn’t matter. Connect the wires.
RVD3_manual_NO-DIODE.indd 17 16 If you have trouble connecting the wires coming out of your wall to the back of your Video Doorbell, use the provided wire extensions and wire nuts. Attach the wire extensions. (optional) Steps for wiring to an existing doorbell Feed all the wires (and the wire nuts, if you used them) into your wall and secure your Video Doorbell on the wall using four screws. Screw it in.
RVD3_manual_NO-DIODE.indd 19 18 Lastly, insert one of the provided security screws into the bottom, and tighten with the starshaped end of the screwdriver bit. Place one of the provided faceplates on your Video Doorbell by slotting it in at the top and clicking it into place. That’s it! Your Video Doorbell is now ready to use. Secure the faceplate. Install the faceplate.
For additional help, visit: ring.com/help Or give us a call… US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. © 2019 Ring LLC or its affiliates. Ring and all related logos are trademarks of Ring LLC or its affiliates. RVD3_manual_NO-DIODE.
1523 26th St. Santa Monica, CA 90404 IMPORTANT PRODUCT INFORMATION SAFETY INFORMATION FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. BATTERY SAFETY Keep the battery and its power adapter in a well-ventilated area and away from heat sources, especially when in use or charging. Do not charge your battery near water or in extremely humid conditions. Do not open, disassemble, bend, deform, puncture or shred the battery.
FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
