Customer Operation & Installation Manual Electric Panel Heater MODELS: EPH10MW / EPH15MW / EPH22MW For safe and reliable operation and optimum performance this appliance must be operated, installed and maintained in accordance with these instructions. Read these instructions thoroughly before attempting installation and operation. Keep these instructions handy for future reference.
Congratulations on the purchase of your Rinnai Electric Panel Heater. BEFORE PROCEEDING WITH THE OPERATION OR INSTALLATION OF YOUR NEW HEATER, PLEASE READ THIS MANUAL THOROUGHLY AND GAIN A FULL UNDERSTANDING OF THE REQUIREMENTS, FEATURES AND OPERATION OF YOUR NEW APPLIANCE.
WARRANTY, FEATURES & SPECIFICATIONS WARRANTY The benefits to the consumer given by this warranty are in addition to all other rights and remedies of the consumer under a law in relation to the goods or services to which the warranty relates. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other loss or damage.
This page intentionally blank Rinnai Australia iii Operation Manual
TABLE OF CONTENTS WARRANTY, FEATURES & SPECIFICATIONS ...................................................................................... ii WARRANTY............................................................................................................................................................ii FEATURES ............................................................................................................................................................. ii SPECIFICATIONS ................
SAFETY & IMPORTANT POINTS UNPACKING THE APPLIANCE If any damage is evident DO NOT INSTALL or OPERATE and contact your supplier for advice. WHAT’S IN THE BOX The package should contain: Heater fitted with flexible cord and plug. A plastic bag containing the Operating and Installation Instructions and mounting screws. Two plastic bags containing four castors, two castor brackets and two clips.
HOW TO OPERATE THE HEATER HEATER LAYOUT 10 6 A 1 9 8 A 2 3 4 3 4 5 7 6 5 A Control panel console 1 MAIN POWER switch 2 Heating control dial 3 Heater operation indicator (Red) 4 Heating level (MIN,1,2,3,4,5,6,7,8,MAX) 5 Comfort Zone Settings* 6 Louvre, warm air discharge 7 240 Volt power cord & plug 8 Air inlet Grille 9 Castors for floor mounting (see “INSTALLATION” on pages 5 & 6 for installation options) 10 Mounting bracket for wall installation (see “INSTALLATION” on pages
HOW TO OPERATE THE HEATER HEATER OPERATION 10 6 A 1 9 8 A 2 3 4 3 4 5 7 6 5 To turn the heater on and set the heating level: Ensure heater is plugged in and the power socket outlet is switched on. 1. Turn the main power switch 1 located on the right hand side of the appliance, to the ON ‘I’ position. 2. Adjust the heating dial 2 to the desired numeric heating level 4 . The heating operation indicator 3 will illuminate to indicate the heater is now in operation.
CARE AND MAINTENANCE CARE OF THE HEATER Due to the ‘natural convection’ operating principle it is normal that some dust and fluff may build up at the air inlet and air outlet louvres over time. This will reduce operating effectiveness and may result in the appliance overheating if left for too long without cleaning. DO NOT use solvents to clean any parts. To remove dust and clean the appliance: 1. Unplug the electric plug of the heater from the socket outlet before commencing cleaning. 2.
INSTALLATION GENERAL This heater is suitable for Do It Yourself installation. It can be either wall mounted (fixed installation) or freestanding by mounting castors in accordance with these instructions. A phillips head screwdriver is required for fixed installation. For wall installation other tools and hardware may be required, depending on the wall material. WALL INSTALLATION The clearance from the sides, front and top of the heater must be at least 100mm as shown in the diagram below.
INSTALLATION 4. Secure the mounting bracket to the wall with the 4 mounting screws. For masonry walls use the plastic plugs with screws provided. For plaster walls obtain suitable plasterboard fasteners from a building hardware supplier. 5. Re-attach the heater to the mounting bracket and secure in place with the locking latch. 6. Remove the cable tie from the flexible cord and insert the 2 pin plug of the heater into the power socket outlet.
CONTACT INFORMATION Australia Pty. Ltd. Internet: www.rinnai.com.au E-mail: enquiry@rinnai.com.au ABN 74 005 138 769 Head Office National Help Lines 10-11 Walker Street, Braeside, Victoria 3195 P.O. Box 460 Tel: (03) 9271 6625 Fax: (03) 9271 6622 Sales & Service Tel: 1300 555 545* Fax: 1300 555 655* Spare Parts & Technical Info Tel: 1300 366 388* Fax: 1300 300 141* *Cost of a local call Higher from mobile or public phones.
