Technical data

ManualsBrandsRinnai ManualsHome building and DecorFS35 ETR

Flame Fire ETR

Electronic Timer and Remote

Operating and Installation Instructions

Freestanding Royale ETR (Australia)

Timberflame FS35 ETR (New Zealand)

Table of Contents

Customer Instructions

Control Panel Layout 2

Operation 3

Setting the Clock 5

Operating the Timers 6

Error Codes 7

Safety Points 8

Troubleshooting 9

Installation Instructions

Location 10

Flueing 11

Gas Connection 11

Log Installation 12

Testing & Commissioning 13

Technical Data 14

Service Contact Points 14

Wiring Diagram 15

Installation Checklist 16

Installer Details 16

IMPORTANT

This appliance shall be installed in accordance with:

•

Manufacturers Installation Instructions.

• Local Gas fitting regulations.

• Municipal Building codes.

• Gas Installation Code AG5601 / AG601 - NZ 5261.

• Any other relevant statutory regulation.

• This appliance must only be installed, serviced and removed by an

authorised person.

• For Australian installation, this appliance must be installed with

the supplied wire dressguard.

Summary of content (16 pages)

PAGE 1
Flame Fire ETR Electronic Timer and Remote Operating and Installation Instructions Freestanding Royale ETR (Australia) Timberflame FS35 ETR (New Zealand) Table of Contents IMPORTANT Customer Instructions Control Panel Layout Operation Setting the Clock Operating the Timers Error Codes Safety Points Troubleshooting 2 3 5 6 7 8 9 Installation Instructions Location Flueing Gas Connection Log Installation Testing & Commissioning Technical Data Service Contact Points Wiring Diagram Installation Checklist Ins
PAGE 2
CONTROL PANEL LAYOUT TIME/TEMP. Display Shows either the time of day, temperatures or coded error messages. LOCK Button Indicates lock function CLOCK ADJUSTMENT AND TIMER INDICATORS Indicates that clock or dual timer programme is being set. Flame Function Med. High heat setting and overides thermostat TIMER Indicator Indicates that TIMER 1 or TIMER 2 has been selected to operate. TIME / TEMP. Adjustment Increases or decreases the temperature setting as well as changing hours or minutes.
PAGE 3
OPERATION • TO OPEN THE CONTROL PANEL Lift lightly in the centre of the lid where there is a catch. The control panel lid will then open backward to an angle. • TURNING ON Press the ON/OFF button to operate the heater. The ON indicator will glow green. The spark generator will be heard before the burner ignites and the ON indicator glows red, indicating that the heater is alight. When the heater warms up, the fan will automatically start.
PAGE 4
• OVERRIDE This function is intended to be used to manually override the current operation of the heater. For example; If the heater is in standby mode (ie. between finishing time and starting time of a Timer), and the OVERRIDE button is selected, then the heater will begin to operate and heat the room. To operate the OVERRIDE simply press the OVERRIDE button. The OVERRIDE indicator will flash. To manually deactivate the OVERRIDE simply press the OVERRIDE button again.
PAGE 5
SETTING THE CLOCK pTR • SETTING THE CLOCK When the appliance is first plugged in or after a power failure, the Digital Display will show --:-- As an example, let’s set the clock to 10:35 am: Press the SET TIMES button once, the Clock indicator will flash. Press and hold the “▲“ button; the minutes will begin to change first, then the time will change by whole hours. Release the button when AM 10:00 shows on the Digital Display.
PAGE 6
OPERATING THE TIMERS • OPERATING THE TIMERS Before operating the Timer(s), the clock time must be correct and a starting time and finishing time for the Timer(s) must be programmed. See page 5. The two Timers operate in the same way. This heater does not commence operation at the programmed starting time. It will attempt to heat a room by the programmed starting time. See Pre-heat page 6, for further explanation. To select the Timer(s) to commence heating.
PAGE 7
ERROR CODES • ERROR CODE MESSAGE The Flame Fire ETR has the ability to check its own operation continuously. If a fault occurs, an Error Message will flash on the Digital Display of the control panel. This assists with diagnosing the fault, and may enable you to overcome a problem without a service call. Please quote the code displayed when enquiring about service. Error Code Probable Cause Comments 11 Ignition Failure Check gas is turned on. Service call if repeated.
PAGE 8
SAFETY POINTS Do not restrict the warm air discharge by placing articles in front of the heater. This appliance must not be used for any purpose other than heating. Do not spray aerosols whilst the heater is operating. Most aerosols contain butane gas, and can be a fire hazard if used near the heater when it is in use. Young children should be supervised at all times. Hand or body contact with the louvres should be avoided.
PAGE 9
TROUBLESHOOTING SOLUTION SYMPTOM CAUSE Burner will not light No power present Ensure power cord is plugged in and turned on No gas present Ensure gas supply is turned on Power cut Air in gas pipe Re-ignite after power is restored Purge air (installer) Ignition Failure Repeat lighting procedure (refer page 3) Smell of gas Leaking gas Turn gas off at meter and call installer Fan not working Heat switch not activated Allow heater to run on HIGH for 15 minutes minimum.
PAGE 10
LOCATION When positioning the heater, the main points governing the location are: 1. Flueing. 2. Warm air distribution. 3. The heater must not be installed where curtains or other combustible materials could come into contact with it. In some cases, curtains may need restraining. See below for minimum clearances required. 4. The heater is not designed to be built into bookcases or shelves or any combustible opening. 5. Check that room ventilation complies with local regulations. 6.
PAGE 11
FLUEING • This heater requires a minimum 3m. flue. • Position the heater. • Suspend a plumbline from the ceiling to the centre of the flue socket. • Mark the centre of the flue in the ceiling. • Make a small hole in the ceiling and double check that the flue system will be at least 25 mm clear of combustible materials. • Cut the hole for the flue. • Fit the ceiling plate, flue and decorative cover. The decorative cover must be able to slide up to give access to the flue spigot.
PAGE 12
LOG INSTALLATION The logset is packed inside the heater and the packaging must be removed prior to installing the logset in its correct position. • Open both side panels. • Remove fastenings on both sides of the top glass retainer. Lift retainer away from heater. • Loosen screws on bottom glass retainer. Carefully lift glass out of bottom channel. • Carefully remove log packaging.
PAGE 13
TESTING & COMMISSIONING Comple • TESTING PROCEDURE Turn gas supply on and plug the unit into the power supply. (Caution 240V.) • TO CHECK BURNER PRESSURE • Refer to Data Plate. • Remove the wiring cover panel. • Remove test point screw and attach manometer to test point. The test point is on the front side of the gas valve. • Light heater, turn to High heat setting and check pressure. • If adjustments are necessary, the regulator is situated on the front of the gas control.
PAGE 14
Comple TECHNICAL DATA Model: FGL35ETRBN (NG) Australia FGL35ETRBL (LP) Australia FS35ETRN (NG) New Zealand FS35ETRL (Propane) New Zealand Rinnai Inbuilt Radiant/Convector, glass-fronted, ceramic log space heater with forced convection and natural draught flue system. 35 MJ/h Natural Gas and Propane. Rinnai Electronic Control Valve. Ceramic Logs, Ember Bed and Heat Burner. 15mm. Copper Flare Connection. Natural Gas 0.95 kPa; Propane 2.40 kPa. Natural Draught. An approved 100mm.
PAGE 15
WIRING DIAGRAM 15
PAGE 16
INSTALLATION / COMMISSIONING CHECKLIST (To be completed by certified Gas Installer) Model: ____________________ NO YES 1. Was a fireplace inspection carried out? (ie. clearances, combustibles etc.) 2. Was chimney inspected? 3. Did chimney require flue liner system to be installed? If NO, did chimney meet specified criteria as per manual? 4. Has specified gas pressure been set? 5. Are decorative logs located correctly on pins? 6. Have ember granules been placed and free of dust and powder? 7.