Use and Care Manual

ManualsBrandsRinnai ManualsCommercial HeatingSE ceramic heater 1-Stage Blk 50k LP

HVAC Guideline Specifications

SE Series

Packaged High Intensity Infrared Radiant Gas Heater

Outdoor/Indoor Commercial/Industrial Applications

Size Range: 35,000 and 50,000 Btuh Input Rating

Models:

Description

Part # NG

Part # LPG

Input (Btuh)

RSE1S35BP/N

RSE1S35SP/N

S/S Enclosure; Aluminum Egg Crate

screen

RSE1S35BN

RSE1S35BP

35,000

RSE1S50BP/N

RSE1S50SP/N

S/S Screen; Aluminized Covers

RSE1S50BN

RSE1S50BP

50,000

Part 1 — General

1.01 SYSTEM DESCRIPTION

Outdoor / Indoor approved overhead mounted, electrically controlled patio and high intensity infrared

radiant heating unit utilizing gas combustion as supplied by Rinnai.

1.02 QUALITY ASSURANCE

A. Heater will be tested, approved, and certified by CSA International in accordance with ANSI

Z83.19b / CSA 2.35b High Intensity Gas-Fired Heaters (indoor use), and additionally in

accordance with ANSI Z83.26 / CSA 2.37 Outdoor Gas-Fired Patio Heaters (outdoor use).

B. Each heater will be subjected to run testing on the assembly line.

C. The heater will be warranted by the manufacturer for defects in material and workmanship for a

period of 3 years on the burner assembly and ceramic tiles that comprise the burner panel, and 1

year on all other parts and components.

1.03 DELIVERY, STORAGE, AND HANDLING

Heater will be stored to secure against damage and handled per manufacturer’s recommendations.

Part 2 — Product

2.01 EQUIPMENT (STANDARD)

A. General:

Factory assembled, single-piece infrared radiant heating unit for overhead mounted patio, space or

area heating application. Supplied with the heater will be all necessary factory installed wiring,

piping, and controls required prior to field installation and start-up.

B. Heater Enclosure Construction:

a. Exterior sheet metal enclosure components, and all interior sheet metal components

exposed to direct heat from the burner will be constructed of 409 grade stainless steel.

b. An interior sheet metal divider in the control compartment, and control mounting bracket

will be constructed of high grade aluminized steel.

c. All exposed surfaces of exterior sheet metal components will have a coating of high

temperature flat black emissive coating.

C. Burner Construction and Emitting Surface:

1. General:

a. Burner body will be constructed of high grade aluminized steel

Summary of content (5 pages)

PAGE 1
HVAC Guideline Specifications SE Series Packaged High Intensity Infrared Radiant Gas Heater Outdoor/Indoor Commercial/Industrial Applications Size Range: 35,000 and 50,000 Btuh Input Rating Models: Description Part # NG Part # LPG Input (Btuh) RSE1S35BP/N RSE1S35SP/N S/S Enclosure; Aluminum Egg Crate screen RSE1S35BN RSE1S35BP 35,000 RSE1S50BP/N RSE1S50SP/N S/S Screen; Aluminized Covers RSE1S50BN RSE1S50BP 50,000 Part 1 — General 1.
PAGE 2
b. c. d. e. f. g. The radiant surface will be comprised of a panel of porous ceramic burner tiles with indentation surface technology creating 372 indentations in the tile radiating surface that increases the emitting surface area by 50%. Ceramic tiles will have a homologous grid of approximately 3400 needled perforations that differ not more than +/- 0.001 inch (0.03 mm) in diameter to create a homogeneous radiant surface.
PAGE 3
b. The gas control will have an inlet pressure tap and an outlet pressure tap to facilitate measurement of gas supply and manifold pressures during servicing. c. Heater will be complete with a ½” pipe nipple and ½” union with ½” female NPT for connection to the gas supply. 4. Heater Zone Temperature Control: a. Space Heating: Each heater zone will be controlled by a 24 Vac infrared set-back thermostat (refer Part 4.01), or other 24 Vac thermostat as supplied by the manufacturer b.
PAGE 4
2. Models RSE1S50BP, RSE1S50BN, RSE1S50SP, RSE1S50SN (50,000 Btuh input): a. When installed outdoors a minimum required clearance to combustibles for will not exceed 16” above the heater when oriented in a horizontal mounting position, and will not exceed 20” above the heater when angle oriented up to 30° from horizontal mounting position b.
PAGE 5
status. A switching mechanism within the thermostat will allow for disabling of the temperature setback feature. d. The thermostat mounting plate will attach to a standard 4” x 4” octagonal electrical box. e. Electrical rating: 24 Vac 4.02 Heater Control: Outdoor Patio Heating Application A. GENERAL A Patio Control Panel will provide individual On/Off control for each heater or each heater zone.