Operating instructions

ManualsBrandsRinnai ManualsDomestic AppliancesSymmetry RDV3610

Table Of Contents

Symmetry

Heat Transfer Kit

Customer Informaon and Installaon Instrucons

It is best to install the Rinnai Heat Transfer Kit at the same time as the Rinnai Symmetry as

unrestricted access to the side of the unit is needed. One kit will heat one room.

The Rinnai Heat Transfer Kit must not be mounted in areas subject to direct splashing—

relevant to underoor installations that could be exposed to water.

The Rinnai Symmetry gas replace must be turned on for the heat transfer system to work

(wall switch to operate).

Installation can be completed by a skilled DIY homeowner, however a licensed electrician is

required to install the wall switch.

Please retain this manual for future reference.

Up to two additional rooms can be warmed through the heat from the transfer system using either a

oor or ceiling outlet.

Suitable for use with the Rinnai Symmetry RDV3610 and RDV3600

Summary of content (12 pages)

PAGE 1
Symmetry Heat Transfer Kit Customer Information and Installation Instructions Up to two additional rooms can be warmed through the heat from the transfer system using either a floor or ceiling outlet. Suitable for use with the Rinnai Symmetry RDV3610 and RDV3600 It is best to install the Rinnai Heat Transfer Kit at the same time as the Rinnai Symmetry as unrestricted access to the side of the unit is needed. One kit will heat one room.
PAGE 2
Limited Warranty Rinnai brings you peace of mind with a 2 year minimum warranty. TERMS AND CONDITIONS 1. During the 24 month period from date of purchase and subject to clauses 2 and 3 below, Rinnai New Zealand Limited (“Rinnai”) will, at its own discretion, either replace or repair any defective product at no charge to the customer. 2. This warranty covers manufacturing defects only.
PAGE 3
Contents About the heat transfer kit 4 Installer information 5 Kit contents 6 Fitting the spigot plate 7 Attaching the 6 m duct 8 Installing and wiring the fan and switch 9 Fitting the ceiling or floor outlets 10 Testing 11 Some wording in these instructions have been written verbatim from the Weiss Heat Transfer System 1 Room to 1 Room instruction sheet (INS601 r05:010702). This wording is denoted with a (W) at the end of the sentence.
PAGE 4
About the heat transfer kit Traditional fires heat one part of the house, but with the Rinnai Symmetry’s innovative heat ducting, heat can be transferred to an additional room in your home. This feature helps you make the most of the heat that is being generated. The fire’s flexible heat ducting can be run horizontally and vertically through a wall or through the floor to distribute warm air to another area without the need for a second heat source.
PAGE 5
Installer information Before installation • Check for damage—do not install any damaged items • Check all components have been supplied, refer kit contents on following page • Read these instructions to get an overview of the steps required before starting General guidelines regarding installation 3m 6 m (cannot be cut) 6 m (cannot be cut) 3m All duct bends to be kept as smooth as possible The heat transfer kit has been specifically designed and tested as a 9 m kit.
PAGE 6
Kit contents The Symmetry Heat Transfer Kit (R3626) comes packaged in one box and contains the following: 1 2 5 6 3 4 7 8 Not included, ordered separately 9 10 Component 11 Quantity 1 Ceiling outlet 1 2 Duct 3 m (150 mm inner diameter) 1 3 Duct 6 m (150 mm inner diameter) 1 4 Spigot plate 1 5 Fan* 1 6 Wall switch 7 High temperature duct tape 1 8 Hanging chain 2 m 1 9 Fastener pack 1 10 Spigot adaptor 1 1 roll Floor outlet (ordered separately) 11 Floor outlet and t
PAGE 7
Fitting the spigot plate 1. Remove the cover panel(s) on the side of the heater and discard. The position of the cover panel will differ according to the model installed. Rinnai Symmetry DV3610: Rinnai Symmetry DV3600: top of unit (as pictured below) bottom of unit 2. Fit the heat transfer spigot adaptor(s) to the side of the fireplace with the screws removed from the cover panel, do not over tighten. When positioned correctly it will be mounted at an angle.
PAGE 8
Attaching the 6 m heat duct 1. Tape the inner duct to the spigot plate. This ensures a secure attachment. 2. Tape the outer duct to the spigot plate. This keeps the outer duct from bunching and touching the side of the fireplace.
PAGE 9
Installing and wiring the fan and switch 1. Install the fan using the hanging chain included in the kit. The fan is designed to be suspended as this helps reduce noise and vibration. Positioning the fan as far away as possible from the outlet will also help to reduce fan noise. Note the direction of air through the fan is correct, this is indicated with an arrow on the side of the fan housing. For ease of servicing, the fan is supplied with the 3-pin plug.
PAGE 10
Fitting the ceiling or floor outlets 1. Check position of ceiling or floor outlet to ensure a 450 mm clearance (for a smooth bend in the duct) and that no ceiling or floor joists are in the way. 2. Scribe with a pencil the position of the ceiling or floor outlet. 3.
PAGE 11
Testing With the fireplace operating and the fan switched on, observe that there is a steady flow of warm air coming from the outlets. The ducting will look inflated, and where there are bends, these should be as smooth as possible. Rinnai New Zealand Ltd.
PAGE 12
Address: 105 Pavilion Drive, Mangere, Auckland PO Box 53177, Auckland Airport, Auckland 2150 0800: Phone: 0800 RINNAI (746 624) (09) 257 3800 Fax: (09) 257 3899 Email: Website: info@rinnai.co.nz www.rinnai.co.nz All Rinnai appliances meet or exceed the safety standards required by New Zealand gas and electrical regulations. Rinnai is constantly improving its products and as such information and specifications are subject to change or variation without notice.