Operation guide Symmetry RDV3611
Important: The Symmetry RDV3611 is recommended for a new build installation into a false (mock) chimney. It is not suitable for retrofitting into an existing masonry fireplace. Appliance must be installed with a Rinnai approved flue system. This appliance shall be installed in accordance with: -- Manufacturer’s installation instructions -- AS/NZS 5601 -- Local regulations and municipal building codes Installation, servicing and repair shall be carried out only by authorised personnel.
: s t n e cont Introduction................................................................4 Safety...........................................................................5 Clearances...................................................................6 General information....................................................7 Wireless controller......................................................8 Wireless controller display..........................................9 Operation of your RDV3611............
Introduction Blending style with innovation Symmetry RDV3611 By installing a Rinnai Symmetry RDV3611 you can be confident that you are choosing an incredibly efficient and safe heating source for your home. Gas consumption 19-33 MJ/h (low to high) Output 3.8-7.5 kW Efficiency 80% 7.
Safety Important WARNING This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Clearances The appliance must not be installed where curtains or other combustible materials could come into contact with the heater. In some case curtains may need restraining. The clearances listed below are minimum clearances unless otherwise stated. Due to the number of different sized Symmetry frames, all dimensions are taken from the edge of the glass.
General information Before operation please read these instructions to get an overview of how to operate, maintain and service your Rinnai gas fire. Cladding and finishes The Symmetry RDV3611 comes in two framing options; framed and frameless. Framed is best suited to a dry wall/plaster finish. The frameless option suits cladding with a finished edge, such as, tiles, brick, or polished granite. With a framed and frameless installation the fire is a permanent fixture.
Wireless controller Your wireless controller is designed to be wall mounted on a bracket, supplied with the controller, within 10 m of the fire. How it operates The controller houses the thermostat that senses the room temperature and communicates information back to the Symmetry RDV3611 via radio frequency. It needs to be positioned in the same room as the Symmetry RDV3611 and the area that requires heating—a place not subject to temperature fluctuation.
Wireless controller display Transmit indicator Indicates the wireless controller is transmitting to the receiver. The symbol will appear for in the LCD for one second. Battery indicator Symbol will flash when batteries need replacing. The wireless controller will remain functional for approximately five days before shutting off. Temperature display Displays the current room temperature. Flame indicator Indicates flame height.
Operation of your RDV3611 Your controller has a built-in child lock function that requires pressing two buttons simultaneously. This function cannot be overridden. To turn the controller on, press PWR and OK at the same time. Pressing PWR will switch the controller off. Fan On start-up, the fan will start approximately four minutes after the heater is switched on. This delay is to reduce the amount of cold air being pushed out into the room.
Modes of operation Manual Automatic Flame control -- Temperature can be set at any level. -- Temperature is regulated to a programmed level and time. -- Time and day of week does not need to be set. -- Time and day of week needs to be set. Allows you to set your preferred flame setting and override the set temperature—your heater will not automatically turn itself off (unless the room exceeds 40 °C).
Programming your controller The clock must be set before the programmed timers will operate. Each day of the week can be programmed for four periods, making a total of 28 programmed periods. Setting the clock 1. With the controller (heater) off, press T for two seconds. 2. Using the UP and DOWN buttons adjust to the correct time. Ensure you have the correct time of the day (AM/ PM). Press OK to accept. 3. Repeat process to adjust the minutes and day of the week.
Operation using the controller The wireless controller will be factory set so synchronising will only be necessary if there is an error, or if the controller has been purchased separately. Synchronising involves the wireless controller sending a signal to the fire so that it can memorise the certified frequency that it operates on.
Operation without the controller If you lose your controller, or the batteries go flat, you can still operate your unit using the control panel on the appliance. Models with the control panel on the lower right hand side Press and release the ON/OFF button. This will start the electronic spark and the Power LED will be permanently illuminated. The pilot will ignite first and then automatically go to the high setting (stage four modulation). Pressing the ON/OFF button again will turn the unit off.
Troubleshooting During installation there will be an initial burning in period where some smoke and smell may be experienced. This is a normal part of the operation. The appliance is fitted with an overheat safety switch. Under overheating conditions this switch will shut off the appliance. If the appliance shuts off repeatedly servicing may be required.
Abnormal flame pattern Each Rinnai Flame Fire has a distinct flame pattern. This should look the same every time you start your fire, after an initial warm up period of approximately 20 minutes. Abnormal flame performance and/ or pattern can indicate a problem with your fire, such as blocked gas injectors, or that the log set (burn media) has shifted from when the fire was first installed. There are some warning signs that could indicate a problem.
Maintenance and servicing All external surfaces of the heater can be cleaned using a soft damp cloth and mild detergent. DO NOT use solvents and do not attempt to clean the heater while it is hot or operating. Rinnai has a maintenance/ service and spare parts network with personnel who are fully trained and equipped to give the best advice on your Rinnai appliance.
Commissioning The installer must complete the installation and commissioning checklist below and make sure this guide is left with you. They must also instruct you in the use and care of the Symmetry, and make sure you understand the safety instructions and operation of the appliance. Checklist FF Appliance positioned in a suitable location (clearances etc.). FF Rinnai flue system installed and tested to ensure effective draw. FF Uprating kit installed if an LPG installation with a vertical termination.
Limited Warranty Rinnai brings you peace of mind with a: 2 Year minimum warranty Terms and conditions 1. During the 24 month period from date of purchase and subject to clauses 2 and 3 below, Rinnai New Zealand Limited (“Rinnai”) will, at its own discretion, either replace or repair any defective product at no charge to the customer. 2. This warranty covers manufacturing defects only.
Experience our innovation Rinnai.co.nz 0800 746 624 http://www.youtube.
