Ripmax Ltd. 241 Green Street, Enfield, EN3 7SJ United Kingdom Tel: +44 (0) 20 82827500 Email: mail@ripmax.com Website: www.ripmax.com Ripmax GmbH Futaba RC - Service Stuttgarter Straße 20/22 75179 Pforzheim Tel: +49(0)7231 46 94 10 Email: info@ripmax.de Website: www.ripmax.de This manual my be subject to errors, omissions and technical changes. Irrtum und technische Änderungen vorbehalten.
General |Notices Wot Trainer Instructions Wot Trainer Anleitung Make sure you read this safety information and the instructions before building your model. Follow exactly the recommended procedures and settings given in the instructions. If you are operating a radio-controlled model aircraft, helicopter, car, multicopter or boat for the first time, we recommend that you enlist the help of an experienced modeler to guide you.
Wot Trainer Instructions | Wot Trainer Anleitung Chris Foss The Designer / Der Designer The fascination of flight captured Chris's imagination early on in his life when he started building, from kits and plans, simple free flight gliders and rubber powered models. By his early teens, Chris was already experimenting with his own designs, several of which have been featured as constructional plans in various aeromodelling magazines.
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Stage 1 / Schritt 1 Stage 6 / Schritt 6 Prepare your aileron servo by fitting the rubber grommets and brass ferrules supplied with the servo. Slide it into it ply mounting tray on the wing panel and mark the position of the mounting holes. Locate the aileron pushrods, plastic clevises and silicon tube retainers.
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Stage 11 / Schritt 11 Stage 16 / Schritt 16 Cut off any excess pushrod with a pair of side cutter or suitable pliers. Slide the wheel onto the axle and fit the collet to the axle, then tighten the wheel collet grub screw while checking the wheel still rotates freely. Schneiden Sie das überschüssige Gestänge mit einem Seitenschneider, oder einer passenden Zange ab.
Wot Trainer Instructions | Wot Trainer Anleitung Installing the undercarriage in trike format Montage des Fahrwerk für die Dreibein Version Stage 20 / Schritt 20 Running your finger over the bottom of the fuselage locate the furthest rearward captive nuts (300mm back from the firewall) and remove the covering from the holes using a sharp knife.
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Stage 29 / Schritt 29 Stage 34 / Schritt 34 Locate the slot in the fuselage for the fin and carefully trim away the covering as shown. Mark the positions of each servo's mounting holes, checking that the orientation of the outputs splines are the same as this image. Finden Sie den Schlitz im Rumpf für das Seitenleitwerk und entfernen Sie vorsichtig die Folie, wie gezeigt.
Wot Trainer Instructions | Wot Trainer Anleitung Stage 39 / Schritt 39 Bolt the horn through the elevator into the retaining plate in other side. Befestigen Sie das Horn durch das Höhenruder in die Trägerplatte auf der Unterseite. Wot Trainer Instructions | Wot Trainer Anleitung Stage 44 / Schritt 44 Now install the servo arm screw. Nun befestigen Sie die Servoarm Schraube.
Wot Trainer Instructions | Wot Trainer Anleitung The Wot Trainer can be built for electric power (using steps 49-59) and the option EP installation pack, or I/C power (using steps 60-77) and the option I/C installation pack. Der WOT Trainer kann mit Elektroantrieb gebaut werden (Schritte 49-59), und das optionales EP Einbau Set, oder als ein Nitro angetriebenes Modell (ab Schritte 60-77) und das optionale Einbau Set für Nitromotoren.
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Stage 58 / Schritt 58 Stage 63 / Schritt 63 Now screw the spinner to the back plate, you may have to loosen and re-align the propeller a few times to get the alignment correct. The spinner may also need trimming to suit your propeller.
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Stage 68 / Schritt 68 Stage 73 / Schritt 73 Tighten the screw in the connector at mid throttle position then screw the arm to the throttle servo. Using the end point adjustment in your radio adjust the high end and low throttle positions (carburettor open is full throttle). Secure the fuel tank to the battery tray with hook and loop or cable tie.
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Decals / Dekor Stage 77 / Schritt 77 Remove the propeller, spinner backplate and take the spacer off from the backplate. Reinstall the backplate, prop, washer and tighten the retaining nut. Now screw the spinner dome to the backplate to finish the installation. Apply the decals as shown right. Befestigen Sie das Dekor, wie rechts gezeigt.
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Flying The Wot Trainer / Den Wot Trainer Fliegen Control Throws / Ruderausschläge For initial flights, we recommend the following control throws - each measured at the widest point of the surface: Elevator: 9~15mm up Rudder: 45mm left 9~15mm down 45mm right Ailerons: 6~9mm up 6~9mm down Für die ersten Flüge empfehlen wir folgende Einstellungen - jede wird am weitesten Punkt der Oberfläche gemessen: Höhen
Wot Trainer Instructions | Wot Trainer Anleitung Wot Trainer Instructions | Wot Trainer Anleitung Notes / Notize n 27 28
