Instruction Manual Bauanleitung A-CF011 Ripmax Ltd. 241 Green Street, Enfield, EN3 7SJ United Kingdom Tel: +44 (0) 20 82827500 Email: mail@ripmax.com Website: www.ripmax.com This manual my be subject to errors, omissions and technical changes. © Ripmax 2018 Copying or reproduction, even in parts require written permission of Ripmax Ltd. Ripmax GmbH Futaba RC - Service Stuttgarter Straße 20/22 75179 Pforzheim Tel: +49(0)7231 46 94 10 Email: info@ripmax.de Website: www.ripmax.
CONTENTS INHALT PAGE / SEITE General Notices Wichtige Hinweise Contents Required to Complete Inhalt erforderliches Zubehör Stages Schritte Control Throws Pre-Flight Checks Spare Parts Ruderausschläge Vorflug Checks Ersatzteile 16 16 16 Flying the Phase 5 Completed Model Balancing Den Phase 5 Fliegen Fertiges Modell Schwerpunkt 17 17 17 2 / 3 4 4 5 - 15 Specification: Wingspan: 1880mm (74”) Length: 1168mm (46”) Flying weight: 1270g (2.
INSTRUCTIONS / ANLEITUNG General Notices INSTRUCTIONS / ANLEITUNG Wichtige Hinweise Make sure you read this safety information and the instructions before building your model. Follow exactly the recommended procedures and settings given in the instructions. Check your equipment regularly for damage and always replace damaged components with original spare parts. Don't re-use any equipment or devices which have been subject to crash or water damage.
INSTRUCTIONS / ANLEITUNG INSTRUCTIONS / ANLEITUNG Stage Schritt Contents / Inhalt Take a moment to identify each of the par ts supplied and read through these instructions before commencing assembly.
INSTRUCTIONS / ANLEITUNG Stage Schritt INSTRUCTIONS / ANLEITUNG Stage Schritt 4 8 Fit suitable 500mm extension lead to your aileron servo. It is a good idea to use a lead-lock, a turn of insulation tape or heat shrink tube over the joint for additional security. Carefully tie the end of the servo lead to the length of string installed in the wing. Remove the film from the pre-cut slot in the aileron.
INSTRUCTIONS / ANLEITUNG Stage Schritt Stage Schritt 12 Schneiden Sie das überschüssige Gestänge mit einem Seitenschneider ab. Wiederholen Sie dieses Verfahren auch für das zweite Querruder. Kleben Sie die Verdrehsicherungen wie gezeigt mit Epoxy vorne und hinten in die Flächen. Stage Schritt 13 17 Insert three hinges into the rudder, ensuring they are located mid-way in their slots.
INSTRUCTIONS / ANLEITUNG Stage Schritt INSTRUCTIONS / ANLEITUNG Stage Schritt 20 Locate the slots at the rear of the fuselage on the fin for the tailplane front joiner and carefully trim the covering away as shown. 24 Slide the pushrod through the connector on the servo arms. With the radio ‘ON’ and the servo in its neutral position, reposition the servo arm and secure using the included screw fit and hold the elevator at its neutral position while you tighten the elevator connector.
INSTRUCTIONS / ANLEITUNG Stage Schritt INSTRUCTIONS / ANLEITUNG Stage Schritt 28 32 Feed the control wires down the tubes in the fuselage and with the servo at its neutral position, reposition the servo arm and secure using the included screw with your servo as shown. Fit the brushless motor using the screws supplied into the captive nuts pre-fitted in the motor mount. Feed the motor wires through the bulkhead.
INSTRUCTIONS / ANLEITUNG Stage Schritt Stage Schritt 36 39 Locate the two tailplane halves and joining rods, then push the larger rod into the rear tube of one tailplane half and the smaller one in the front. Now slide the tailplane half through the fuselage and side the other tailplane on. This should be a tight fit, if not you can bow the front wire a small amount and then refit the tailplane, this should make a tighter fit. There are a series of cooling holes in the underside of the fuselage.
INSTRUCTIONS / ANLEITUNG Control T hrows / Ruderausschläge Flying the Phase 5 / Den Phase 5 Flie gen For initial flights, we recommend the following control throws each measured at the widest point of the surface. With experience these rates can be increased for high performance aerobatics.
Instruction Manual Bauanleitung A-CF011 Ripmax Ltd. 241 Green Street, Enfield, EN3 7SJ United Kingdom Tel: +44 (0) 20 82827500 Email: mail@ripmax.com Website: www.ripmax.com This manual my be subject to errors, omissions and technical changes. © Ripmax 2018 Copying or reproduction, even in parts require written permission of Ripmax Ltd. Ripmax GmbH Futaba RC - Service Stuttgarter Straße 20/22 75179 Pforzheim Tel: +49(0)7231 46 94 10 Email: info@ripmax.de Website: www.ripmax.
